Bacnet Binary Values - ABB FBVi-2U4-4T User Manual

BACNET BINARY VALUES

POINT SETPOINT OBJECTNAME
BLOCK
balanceModeLo
45 Yes
fanStatus
88 No
sliderEnable
95 Yes
occOvr
97 No
coolMode
113 No
heatMode
114 No
remoteZoneTempEnb
117 Yes
ventMode
118 No
occMode
120 No
UI1_ZoneTempFailure
124 No
fanAlarm
127 No
occSensorCmd
161 No
CBTStatStptEnb
164 Yes
intScheduleEnb
168 Yes
highCO2Alarm
194 No
lowZoneTempAlarm
196 No
reverseDO09
198 Yes
reverseDO10
200 Yes
reverseDO11
202 Yes
balanceModeHi
204 Yes
reverseAO14
205 Yes
reverseAO15
206 Yes
UI3_DischargeTempFailure
208 No
lowAirFlowAlarm
214 No
lowDischAirTempAlarm
217 No
airflowCalibrationAlarm
219 No
leakingDamperAlarm
221 No
©ABB 2021 All Rights Reserved.
Subject to change without notice
WWW.CYLON.COM
FBVi-2U4-4T |
DESCRIPTION
If set to TRUE, Flow will be recorded to
LO_KFactor
If set to FALSE, KFactor will be recorded to
LO_KFactor
If UI4 is set up for a fan status, displays
current fan status.
Enable the sliderSpanStpt (A138) to be used
for UI2.
When the occupied override is active.
Will be On if the unit is in cooling mode.
Will be On if the unit is in heating mode.
Enable the remoteZoneTemp as the active
zone temperature.
Will be On if the unit is in occupied mode.
If UI1 is being used as the active zone
temperature and the temperature reading is
out of range, the alarm will be enabled.
If UI4 is used as the fan status, and the fan is
commanded on and the fan status is open, the
alarm will be enabled.
If an input is set up for an occupancy sensor,
the active status of the occupancy sensor.
CBT-Stat lockout that prevents user
adjustment of setpoints. On = locked out.
Enable the internal BACnet schedule. Disables
occCmd (A269).
If the CO2Demand is above 50% for more than
10 minutes, enable the alarm.
If the active Zone Temperature is below the
active heating setpoint for more than 15
minutes, enable the alarm.
Reverse the operation of digital output DO09
Reverse the operation of digital output DO10
Reverse the operation of digital output DO11
If set to TRUE, Flow will be recorded to
HI_KFactor
If set to FALSE, KFactor will be recorded to
HI_KFactor
Reverse the operation of analog output AO14
Reverse the operation of analog output AO15
If UI3 is used as the active discharge air
temperature and the temperature reading is
out of range, the alarm will be enabled.
If the active airflow is more than 30% below
the active airflow setpoint for more than 5
minutes, enable the alarm.
If the discharge air temperature is more than
15 degrees below the discharge air
temperature setpoint for more than 10
minutes, enable the alarm.
If the active airflow is more than 10% higher
than the maximum cooling flow setpoint for
than 10 minutes, enable the alarm.
If the damper command is at 0% and the
active airflow is above the minHeatFlowStpt
(A230) for more than 10 min, enable the alarm.
APPENDIX: List of
ACTIVE INACTIVE DEFAULT VALUES
TEXT TEXT
IMP STG. MET STG.
On Off
0
On Off
0
Enable Disable
0
On Off 0
On Off
On Off
On Off 0
On Off
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
On Off 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
99