Page 1
BARCO PROJECTION SYSTEMS CM 100 Motorized 800-1000 series R9828870 (230V) R9828879 (120V) INSTALLATION MANUAL Motorized Ceiling Mount CM100 Date: 02/02/2000 Rev: 00 Art. No.: R5976122...
Page 2
Produced by BARCO NV,january 2000 All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visite Barco at the web : http://www.barco.com Printed in Belgium...
Necessary Tools ..................................20 Electrical connection ................................20 Electrical connection+Adjustment of the lift-up range ............... 21 Adjusting the lift-up range ..............................21 Electrical connection+Adjustment of the lift-up range ............... 22 Electrical diagram ................................... 22 BARCO 3 Projection Systems...
Safety CAUTION THIS SUPPORT IS DESIGNED FOR USE ONLY WITH THE BARCO 800 AND 1000 SERIES PROJECTORS. USE WITH OTHER APPLIANCES MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY CAUTION INSTALLING THE SUPPORT MOUNT SHOULD BE PERFORMED ONLY AFTER YOU ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND INSTALLATION GUIDELINES.
Z3499410 CD MNS SW HD 4G1.5 0.25 R3623758 SCR D933 M 8 X 20 SS Z3499411 CD MNSPINS 3G1 CEE R3631069 SCR Z933 M 3 X 10 SS R3631239 SCR Z933 M 4 X 10 SS Illustration BARCO 6 Projection Systems...
Attach the ceiling plate to the ceiling. TEST THE FIXATION TO THE CEILING FOR SAFETY AND RIGIDITY UN- DER MODERATE SIDE LOADS (SWAYING) AND TEST TO AT LEAST 800KG (1765LBS) PULL DOWNWARD FOR SAFETY; To be continued on next page. BARCO 8 Projection Systems...
Mounting the Ceiling Plate (Continued) Lay-out ceiling Following diagram shows the dimensions of the ceiling plate and also the position of the plate different fixation holes. BARCO 9 Projection Systems...
(see illustration below). Subtract the H value from the value CD to obtain the correct length of the rod. Rod Length ceiling screen BARCO 10 Projection Systems...
Put a nut M12 (A) on each rod (B) (to be used later to lock the inserted rod) Insert the four rods fully in the respective welded nut (C) on the ceiling plate Lock the position of the rods by tightening the provided nut (C) against the ceiling plate. BARCO 11 Projection Systems...
Slide the motor unit over the rods fully against the locking nuts of the rods. Put a nut M12 (D) on each rod (B) and turn it fully on the rod, tightening the motor unit. FRONT PROJECTOR REAR PROJECTOR BARCO 12 Projection Systems...
M12 (D) through the bracket and loop, and secure with a nut M12 (E). Put a nut M12 (F) on each rod, a few centimeter from the top (used later for securing the projector support). BARCO 13 Projection Systems...
Slide the projector on the support, as illustrated in drawing below, until the lock screws (B) fits the provided gap (C). Secure the position of the projector on the support by tightening a nut (D) on both lock screws. BARCO 14 Projection Systems...
Attention: for safety reasons, both nuts must be turned fully on the rods. Turn the nuts (D) fully against the support without tightening and proceed to the alignment of the motorized ceiling mount assembly. BARCO 15 Projection Systems...
(turning clockwise lifts up the projector, counterclockwise lowers the projector) Secure the position of the projector/support by fastening the safety-nuts (C). Illustrations Nut 1 Nut 2 Nut 3 BARCO 16 Projection Systems...
Loosen the safety-nut (C) on top and rear of the projector support. Adjust the adjustable screw (A) clock- or counterclock wise until the projector axis is perpendicular on the screen. Secure the position of the projector/support by fastening the safety-nuts (C). Illustrations BARCO 17 Projection Systems...
This product should be operated from an AC power source: done Art. No: r9828870 from a 230V AC power source Art. No: r9828879 from a 120V AC power source If you are not sure of the type of AC power available, consult your dealer or local power company before ordering.
Check the adjusted range, using the commander, and if correct, put back the yellow protection cap (A) on top of the pulley motor. WIRING DIRECTION OF ROTATION brown wire white button black wire yellow button BARCO 21 Projection Systems...
Electrical connection+Adjustment of the lift-up range Electrical The diagram below shows the electrical interconnection of the motor, mains suply and diagram commander. CEE 7 ANSI C73.11 BARCO 22 Projection Systems...