2: Ifx1 (Insert Effect1); 3: Ifx2 (Insert Effect2); 4: Ifx3 (Insert Effect3); 5: Ifx4 (Insert Effect4) - Korg Karma Parameter Manual

7.2–1c: UTILITY
I
"GM Initialize" (1.1–1b), "Solo Selected Track," "Set Loca-
tion," (SEQ 1.1–1d), "Copy Insert Effect," "Swap Insert
Effect," "DKit IFX Patch" (COMBI 7.1–1d), "Select by Cat-
egory" (PROG 7.2–1b)
7.2–2: IFX1
(Insert Effect1)
7.2–3: IFX2
(Insert Effect2)
7.2–4: IFX3
(Insert Effect3)
7.2–5: IFX4
(Insert Effect4)
7.2–6: IFX5
(Insert Effect5)
Sets the parameters for the effects selected for IFX 1–5 in the
Setup page ( p.168).
7.2–7: Route
(Routing)
7.2–7a
7.2–7a: Routing Map
This shows the status of the insert effects. This displays the
same contents as the 7.1: BUS, Routing page. ( 7.1–3a)
7.2–7b: UTILITY
I
"GM Initialize" (1.1–1b), "Solo Selected Track," "Set Loca-
tion," (SEQ 1.1–1d), "Copy Insert Effect," "Swap Insert
Effect," "DKit IFX Patch"(COMBI 7.1–1d)

S.PLAY 7.3: Master FX

For details on the master effects, refer to p.159 "7. Effect
Guide."
7.3–1: Setup
Here you can select the type of master effects, turn them on/
off, and make chain and master EQ settings.
This is the same as Program mode with the exception of
"MFX1 Control Ch," "MFX2 Control Ch," and "MEQ Con-
trol Ch." ( PROG 7.3: Ed-MasterFX)
7.3–1a
7.3–1b
7.3–1c
7.3–1a: Master FX Setup
MFX1 On/Off, MFX2 On/Off
Master Effect 1, 2
Rtn 1, 2 (Return 1, 2)
This is the same as in Program mode. Refer to "PROG 7.3–1:
Setup." However, unlike Program mode, the master effects
will be controlled by the MIDI channel specified by "MFX 1,
2 Control Ch." The control changes used are the same as in
Program mode.
MFX1, 2 Control Ch
Specifies the MIDI channel that will control dynamic modu-
lation (Dmod) for the master effects.
G ch: The effect will be controlled on the global MIDI chan-
nel "MIDI Channel" (GLOBAL 2.1–1a). Normally you will
leave this at Gch.
7.3–1b: Master FX Chain
7.2–7b
MFX Chain
Direction (Chain Direction)
Signal (Chain Signal)
Level (Chain Level)
This is the same as in Program mode. Refer to p.40 "PROG
7.3–1: Setup."
7.3–1c: MEQ Ctrl
MEQ Ctrl (MEQ Control Ch)
Specifies the MIDI channel that will control dynamic modu-
lation (Dmod) for the master EQ.
G ch: The effect will be controlled on the global MIDI chan-
nel "MIDI Channel" (GLOBAL 2.1–1a). Normally you will
leave this at Gch.
7.3–1d 7.3–1e
[Off, ON]
[000...089: name]
[000...127]
[Ch01...16, G ch]
[MFX1→MFX2, MFX2→MFX1]
[LR Mix, L Only, R Only]
[000...127]
[Ch01...16, G ch]
131