083: Wah-Ampsim (Wah/Auto Wah - Amp Simulation); 084: Deci-Ampsim (Decimator - Amp Simulation); 085: Deci-Comp (Decimator - Compressor) - Korg Karma Parameter Manual

083: Wah–AmpSim
(Wah/Auto Wah – Amp Simulation)
This effect combines a mono-type wah and an amp simula-
tion. You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Wah/Auto Wah
+
Wah
Right
Sweep Mode
Envelope
Auto
D-mod
D -mod
LFO
LFO
[WAH] Freq Btm (Frequency Bottom)
Sets the lower limit of the wah center frequency
a
Top (Frequency Top)
Sets the upper limit of the wah center frequency
Swp Mode (Sweep Mode)
Selects the control from auto-wah, modulation source, and LFO
b
Src (Source)
Selects the modulation source for the wah when Swp Mode=Dmod
lfoF (LFO Frequency)
c
Sets the LFO speed
Resonance
Sets the resonance amount
d
LPF (Low Pass Filter)
Switches the wah low pass filter on and off
[AMP] Amplifier Type
e
Selects the type of guitar amplifier
[Routing]
f
Switches the order of the wah and amp simulation connection
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
g
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
084: Deci–AmpSim
(Decimator – Amp Simulation)
This effect combines a mono-type decimator and an amp sim-
ulation. You can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Decimator
Resolution
+
Decimator
Pre LPF
Right
[DECI] Pre LPF
a Turn the harmonic noise caused by lowered sampling on and off
High Damp
b
Sets the ratio of high-range damping
Sampling Freq (Sampling Frequency)
c
Sets the sampling frequency
210
Routing
Amp Simulation
Amp Simulation Filter
Auto, Dmod, LFO
WAH → AMP, AMP → WAH
Dry, 1:99...99:1, Wet
Routing
Amp Simulation
Output Level
Amp Simulation Filter
High Damp
1.00k...48.00kHz
Resolution
d
Sets the data bit length
Level (Output Level)
e
Sets the decimator output level
[AMP] Amplifier Type
f
Selects the type of guitar amplifier
[Routing]
g
Switches the order of the wah and amp simulation connection
Wet / Dry
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
h
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
Wet / Dry
085: Deci–Comp
0...100
Fx:009
This effect combines a mono-type decimator and a compres-
0...100 sor. You can change the order of the effect connection.
Fx:009
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Fx:009,
Off...Tempo
+
0.02...20.00Hz
0...100
Right
Off, On
SS, EL84, 6L6
[DECI] Pre LPF
Turn the harmonic noise caused by lowered sampling on and off
a
High Damp
Sets the ratio of high-range damping
Sampling Freq (Sampling Frequency)
b
Sets the sampling frequency
Off...Tempo
Resolution
c
Sets the data bit length
–100...+100
Level (Output Level)
d
Sets the decimator output level
[CMP] Sensitivity
e
Sets the sensitivity
Attack
Sets the attack level
f
Level (Output Level)
Sets the compressor output level
[Routing]
g
Switches the order of the decimator and compressor connection
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
Wet / Dry
(Source)
h
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
Wet / Dry
Off, On
Fx:014
0...100%
(Decimator – Compressor)
Routing
Compressor
Decimator
Resolution Output Level
Decimator
Pre LPF High Damp
Envelope - Control
4...24
Fx:014
0...100
Fx:014
SS, EL84, 6L6
DECI→AMP, AMP→DECI
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
Comp
Output Level
Wet / Dry
Off, On
Fx:014
0...100%
1.00k...48.00kHz
4...24
Fx:014
0...100
Fx:014
1...100
Fx:002
1...100
Fx:002
0...100
Fx:002
DECI→CMP, CMP→DECI
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100