Sw1/2 Assign; Sw1, Sw2 Assign List - Korg Karma Parameter Manual

SW1/2 Assign

The following functions can be assigned to the [SW1] or
[SW2] keys.
• For a Program, Combination, Song, or Song Play mode
make the settings in 2.2: Ed-Ctrl/Controller page "SW1/
2 Assign" (2.2–1b).

SW1, SW2 Assign List

Off
SW1 Mod.(CC#80) (SW1 Modulation:CC#80)
SW2 Mod.(CC#81) (SW2 Modulation:CC#81)
Porta.SW(CC#65) (Portamento Switch:CC#65)
Octave Down
Octave Up
JS X Lock
JS+Y Lock
JS-Y Lock
Ribbon Lock :N/A
JS X&Rbn Lock :N/A
JS+Y&Rbn Lock :N/A
JS-Y&Rbn Lock :N/A
AfterT Lock
SW1 Mod.(CC#80) (SW1 Modulation:CC#80)
SW2 Mod.(CC#81) (SW2 Modulation:CC#81)
This effect differs between SW1 and SW2. SW1 is handled as
CC#80, and SW2 is handled as CC#81.
Porta.SW(CC#65) (Portamento Switch:CC#65)
When "Mode (Oscillator Mode)" (PROG 2.1–1a) is Single,
turning the switch on (LED lit) will apply portamento
regardless of the "Enable (Porta. Enable)" (PROG 3.1–1c)
setting, and turning the switch off (LED off) will not apply
portamento.
If "Mode (Oscillator Mode)" is Double, and if the "Enable
(Porta. Enable)" setting is the same for OSC1 and 2 (i.e.,
Enable or Disable for both OSC1 and 2), then portamento
will be applied to OSC1 and 2 when the switch is turned on
(LED lit), and portamento will not be applied to OSC1 and 2
when the switch is turned off (LED off).
If the "Enable (Porta. Enable)" setting is different for OSC1
and 2 (i.e., OSC1 is Enable and OSC2 is Disable, or OSC1 is
Disable and OSC2 is Enable), then portamento will be
applied to the OSC whose setting is Enable when the switch
is turned on (LED lit), and portamento will be applied to
neither OSC when the switch is turned off (LED off).
230
no function
Select this when using the switch as an Alternate Modulation or Effect Dynamic Modulation
source. In this case, you must first specify the control destination. Each time the switch is turned
On/Off, a CC#80 (or CC#81) message will be transmitted (Off: 0, On: 127).
When you press SW1 (or SW2) to turn it on (LED lit), portamento will be applied. Each time this is
turned On/Off, CC#65 will be transmitted (Off: 0, On: 127).
Each time you press SW1 (or SW2), the pitch will alternate between 1 octave lower
and the original octave setting (1 octave down when the LED is lit).
Each time you press SW1 (or SW2), the pitch will alternate between 1 octave higher
and the original octave setting (1 octave up when the LED is lit).
Lock the effect of the joystick X direction.
Lock the effect of the joystick +Y direction.
Lock the effect of the joystick -Y direction.
Lock the effect of after touch.
JS X Lock, JS+Y Lock, JS-Y Lock, AfterT Lock
The state of the selected controller (joystick, after touch) will
alternate between Lock and Unlock (Lock when the LED is
lit).
While the joystick or after touch is being operated, turning
Lock on will lock (fix) the effect at the current position of
that controller.
For example if you select JS+Y Lock, move the joystick
away from yourself, and then turn Lock on, the operation
produced by the joystick (+Y) will be locked (held) at that
position. Even if you return the joystick to its original posi-
tion, the modulation will continue to apply. At this time you
can even move the joystick in the –Y direction to apply both
types of modulation (joystick +Y and –Y) simultaneously.
Ribbon Lock: N/A, JS X&Rbn Lock : N/A,
JS+Y&Rbn Lock: N/A, JS-Y&Rbn Lock: N/A
These values can be specified, but will have no actual effect.
N/A indicates Not Available (i.e., invalid).
Data compatibility is maintained between this instrument
and the TRITON/TRITONpro/TRITONproX (TRITON key-
board models). Programs created on this instrument can be
used on TRITON keyboard models, and the opposite is also
true.
In order to maintain compatibility, it is possible to specify
these "invalid" parameters on this instrument.
—
—
—
—
When you Lock the joystick or after touch, MIDI trans-
mission of the corresponding controller will be halted,
but reception will still occur.
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)
( p.230)