2: Ifx1 (Insert Effect1); 3: Ifx2 (Insert Effect2); 4: Ifx3 (Insert Effect3); 5: Ifx4 (Insert Effect4) - Korg Karma Parameter Manual

7.2–1b: Control Channel
Control Channel
Indicates the MIDI channel that will control effect
dynamic modulation (Dmod), pan following the insert
effect "Pan (CC#8)," "Send 1 (MFX1)," and "Send 2
(MFX2)."
An asterisk "*" will be displayed at the right of the channel
number Ch01–16 for tracks that are routed to an IFX. If mul-
tiple tracks with differing MIDI channel settings are routed,
these channels specify the channel that will be used to con-
trol the effect.
All Rt. (All Routed): Control can be performed from any of
the MIDI channels of the tracks that are routed.
If "BUS Select" (7.1–1a/2a) is set to DKit for a track in
which a drum program is selected, the MIDI channel of
that track will be valid if any IFX1–5 is set to All Rt.,
regardless of the drum kit "BUS (BUS Select)" (GLO-
BAL 5.1–3a) setting or the utility setting "DrumKit IFX
Patch."
7.2–1c: UTILITY
I
"Memory Status", "Solo Selected Track", "FF/REW
Speed", "Set Location" (1.1–1c), "Copy Insert Effect,"
"Swap Insert Effect" (7.1–1b/2b), "Select by Category"
(PROG 7.2–1b)
7.2–2: IFX1
(Insert Effect1)
7.2–3: IFX2
(Insert Effect2)
7.2–4: IFX3
(Insert Effect3)
7.2–5: IFX4
(Insert Effect4)
7.2–6: IFX5
(Insert Effect5)
Sets the parameters for the effects selected for IFX 1–5 in the
Setup page ( p.168).
7.2–2(...6)a: UTILITY
I
"Memory Status" (1.1–1d)
7.2–7: Route
[Ch01...16, All Rt.]
7.2–7a
7.2–7a: Routing Map
This shows the status of the insert effects. This displays the
same contents as the 7.1: BUS, Routing page. ( 7.1–3)
7.2–7b: UTILITY
I
"Memory Status", "Solo Selected Track", "FF/REW
Speed", "Set Location" (1.1–1c), "Copy Insert Effect,"
"Swap Insert Effect" (7.1–1b/2b), "Select by Category"
(PROG 7.2–1b)
For details on the master effects, refer to p.159 "7. Effect
Guide."
7.3–1: Setup
Here you can select the type of master effects, turn them on/
off, and make chain and master EQ settings.
This is the same as Program mode with the exception of
"MFX1 Control Ch," "MFX2 Control Ch," and "MEQ Con-
trol Ch." ( PROG 7.3: Ed-MasterFX)
7.3–1a
7.3–1b
7.3–1c
7.3–1a: Master FX Setup
7.2–2a
MFX1 On/Off, MFX2 On/Off
Master Effect 1, 2
Rtn 1, 2 (Return 1, 2)
This is the same as in Program mode. Refer to "PROG 7.3–1:
Setup." However, unlike Program mode, the master effects
will be controlled by the MIDI channel specified by "MFX 1,
2 Control Ch." The control changes used are the same as in
Program mode.
(Routing)

SEQ 7.3: Master FX

7.3–1d
[000...089: name]
7.2–7b
7.3–1e
[Off, ON]
[000...127]
113