1: Parm1 (Parameter 1); 2: Parm2 (Parameter 2) - Korg Karma Parameter Manual

A/B/C/D GE CC-A
A/B/C/D GE CC-B
A/B/C/D GE Env.1
A/B/C/D GE Env.2
A/B/C/D GE Env.3
p.28 PROG 6.1–4a: Tx Filter
6.1–6b: UTILITY
I
"Write Combination," "Solo Selected Timbre" (1.1–1c)
"Copy KARMA Module" (PROG 6.1–1c)
"Init KARMA Module" (6.1–1d)
"Select by Category" (1.1–4d)
COMBI: 6.2 Ed-KARMA Mdl
6.2–1: Parm1
(Parameter 1)
Here you can set KARMA module parameters. In Combina-
tion mode, four KARMA modules ([A], [B], [C], [D]) can be
used.
Use the [F6] (" ") key and [F7] ("
1d) to select the KARMA module that you wish to edit.
6.2–1a 6.2–1b 6.2–1c
6.2–1a: Module Parameter
The selected KARMA module is displayed as [A], [B], [C], or
[D].
Transpose
Force Range
[Off, Lowest, Highest, C3–B3[1], C3–B3[2]]
Delay Start
Delay Start Fixed
Quantize Trig
p.29 PROG 6.2–1a: Module Parameter, BG p.88 "About the
KARMA function — KARMA function synchronization"
TimbZ Bypass (TimbZone Bypass)
Specifies whether the key zone settings (3.3–1b) and velocity
zone settings (3.4–1b) of the timbre will be applied to the
phrase or pattern generated by the KARMA module.
On (checked): The key zone settings and velocity zone set-
tings of the timbre will be bypassed for the phrase or pattern
generated by the KARMA module. The settings of the tim-
bre will be ignored, and the notes generated by the KARMA
module will be sounded.
Off (unchecked): The key zone settings and velocity zone
settings of the timbre will be applied to the phrase or pattern
generated by the KARMA module. Notes generated by the
KARMA module will not be sounded if they are outside the
key zone or velocity zone of the timbre.
[Off, On] Root Position
[Off, On] p.29 PROG 6.2–1a: Module Parameter
[Off, On]
6.2–1b: Tx CC (Transmit CC)
[Off, On]
[Off, On]
p.30 PROG 6.2–1b: Tx CC
These messages will be transmitted on the "Output Chan-
nel" (6.1–2a) of the KARMA module.
Tx CC1...4 Number
p.30 PROG 6.2–1b: Tx CC
6.2–1c: Value (Tx CC Value)
Value (Tx CC1...4 Value)
p.30 PROG 6.2–1c: Value (Tx CC Value)
6.2–1d:
Use the [F6] ("
select the KARMA module that you wish to edit.
I
"Write Combination," "Solo Selected Timbre" (1.1–1c)
") key (6.2–
6.2–2: Parm2
6.2–2a
6.2–1d 6.2–1e
6.2–2a: Trigger/Latch
[–36...+36]
Specifies the trigger conditions and latch on/off for the GE
that is selected for each KARMA module [A]–[D].
[Off, Fixed, 3...4x ] Note:
Note Trigger
[0000 ms...5000 ms]
p.31 PROG 6.2–2a: Trigger/Latch, "Note Trigger"
[Off, On]
[Off, On]
,
") key and [F7] ("
6.2–1e: UTILITY
"Copy KARMA Module" (PROG 6.1–1c)
"Init KARMA Module" (6.1–1d)
"Select by Category" (1.1–4d)
(Parameter 2)
6.2–2b
[Off, On]
[Off, 000...095]
[000...127]
") key to
6.2–2c 6.2–2d
[Any, AKR, 1st, Dyn]
61