Advertisement
Quick Links
SINGLE POST HOIST
AutoLift AL-182093
Air / Hydraulic Single Post Vehicle Hoist
1360Kg Maximum Lifting Capacity
Design Registration Approval Number: N/A
Design Code: AS1418.9-1996
Note: While all due care and attention has been taken in the preparation of this document, Advance AutoQuip shall not be liable for any inaccuracies or omissions
Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au
INSTALLATION MANUAL & OPERATION
INSTRUCTIONS
- READ THE ENTIRE CONTENTS OF THIS MANUAL BEFORE
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS
OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS.
FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE
Specifications subject to change without notice.
which may occur therein
Advance AutoQuip
2 McDonald Crescent | Bassendean WA 6054
INJURY OR DEATH.
READ FIRST
DO NOT use the
machine until you read
and understand all the
dangers, warnings and
cautions in this manual.
Advertisement
Related Manuals for AAQ AutoLift AL-182093
Summary of Contents for AAQ AutoLift AL-182093
- Page 1 Note: While all due care and attention has been taken in the preparation of this document, Advance AutoQuip shall not be liable for any inaccuracies or omissions which may occur therein Advance AutoQuip 2 McDonald Crescent | Bassendean WA 6054 Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au...
- Page 2 DEFINITION 1. It is a mobile hydraulic hoist, with a column structure, built and manufactured to allow the operator to work on wheels or under‐doors at men’s height. The raise and recent movement are obtained using a sleigh fixed to a chain connected to a hydraulic cylinder. 2. Hydra‐pneumatic pump with foot control reduced dimensions and a ...
-
Page 3: Technical Description
TECHNICAL DESCRIPTION The hoist consists of: The Column - The basic part of the system consists of a specially shaped column of folded metal sheet into which the lifting carriage and cylinder are placed. The Base - The base is D-shaped with fixed wheels at two of its ends and another two swivel ones at the opposite ends. - Page 4 Fig. 3 Fig. 5 Fig. 4 Fig. 6 Now the hoist is ready for use. 7 / 13 ...
- Page 5 SAFTY INSTRUCTIONS AND WARNINGS: 1: DO NOT exceed the rated capacity:1360Kg. 2: DO NOT stand under the work place when the hoist is working. 3: This hoist is mainly for lifting. Operator only can work with the support of jack stand. Also make sure the surround situation is safe.
- Page 6 you will have to replace the holding device. To do this, follow the next steps: a. Lift up the far end of the wheel fork, then take it out from the groove on the carriage. b. Insert the frame adaptor into the groove (Fig. 9). Fig.
-
Page 7: Parts Drawing
PARTS DRAWING 10 / 13 ... - Page 8 11 / 13 ...
- Page 9 PARTS CODE LIST ITEM CODE DESCRIPTION NOTE ES04-00010-000 Handle sleeve 5206-00016-000 Hex nylon locknut φ16 5302-00016-000 Flat washer SL01-05000-000 column cover SL01-01000-000 Column φ6 5302-00006-000 Flat washer M6*12 5104-06012-000 Hex bolt SL01-00002-000 block wheel SL01-00001-000 long bolt SL01-00022-000 Bush M16*195 SL01-00007-000 Hex bolt SL01-00014-000...
- Page 10 ITEM CODE DESCRIPTION NOTE Wheel SL01‐00010‐000 SL01-04000-000 basement M6*20 5105-06020-000 socket head cap screw SL01-00013-000 Sliding block SL01-00003-000 Chain SJ13-00030-000 β pin SL01-00016-000 chain shaft SL01-09001-000 Roller(Ⅰ） SL01-10001-000 Roller(Ⅱ） φ20 5302-00020-000 flat washer SL01-03000-000 carriage body SL01-00005-000 Oil connector 5903-00014-000 Combined Washer JP17-04005-000 Throttle valve...
- Page 11 THIS WARRANTY SUPERSEDES ALL OTHER WARRANTY POLICIES PREVIOUSLY STATED AND IN ALL OTHER ADVANCE AUTOQUIP’s PRODUCT SPECIFIC LITERATURE. Advance AutoQuip 2 McDonald Crescent | Bassendean WA 6054 Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au...
- Page 12 SAFETY OPERATING PROCEDURES Vehicle Hoist DO NOT use this machine unless the operator has been thoroughly instructed in its safe use and operation. Safety glasses must be worn at all Long and loose hair must be times in work areas. contained.
- Page 13 COMMISSIONING REPORT 1. Details of Customer Customer Name: Installation Address: 2. Hoist Details Model No: 2 McDonald Crescent Hoist Type: Bassendean WA 6054 Installation Date: P: 08 9279 1663 | E: sales@aaq.net.au 3. Commissioning Report Comments Safety Devices Safety devices incorporated into the design of the vehicle to AS/NZS 1418.9 Welds Visual check all welds completed and comply to requirement of AS/NZS 1554 Hydraulic Equipment and Controls Visual check carried out for leaks Pneumatic Equipment and Controls Visual check carried out for leaks Safety Locks Safety locks tested for correct operation Support Pads Checked for good working order Wheel Stops Supplied with the hoist and in good working order Hoist Motion Limits Checked for correct operation Load Test and Speed Check Hoist checked with load for correct operation and speed control tested Wire Ropes Checked wire ropes for correct installation and tension Concrete Floor Concrete floor is a suitable depth for installation...
- Page 14 COMMISSIONING REPORT Location of Vehicle Hoist & Vehicle Clearances Vehicle hoist or any part of the load is positioned no less than 600mm away from any fixed structure Provisions have been made for effective clearances above the vehicle when the hoist is in its fully raised position. Markings ‐ Hoist Checked for Relevant Marking Including: Make & Model Number Serial number Rated Capacity Reference to maintenance Operation instructions Screw and Nut Gaps Hoist compliance plate showing design registration Functional Test Vehicle hoist has been tested and all safety devices, limit switches and control function interlocks have been tested for correct operation. Demonstration The installer has demonstrated the operation of the vehicle hoist to the owner or operator Electrical Equipment and Controls Lock off isolating switch installed Emergency stop button installed 3. Details of Electrical Contractor Trading Name: EC Licence Number: Address: Telephone Number: 4. Signature Name: ___________________________________________________________ Date: I, being the person responsible for completing the commissioning report have exercised reasonable skill and competency when completing the report and herby certify that the vehicle hoist has been commissioned fit for use as per the Australian / New Zealand Standard 1418.9:1996 Vehicle Hoists.