Advertisement
Quick Links
SINGLE POST HOIST
AutoLift AL-167261
Single Post Storage Hoist
1000Kg Maximum Lifting Capacity
Design Registration Approval Number: WAH22329
Design Code: AS1418.9-1996
Note: While all due care and attention has been taken in the preparation of this document, Advance AutoQuip shall not be liable for any inaccuracies or omissions
Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au
INSTALLATION MANUAL & OPERATION
INSTRUCTIONS
- READ THE ENTIRE CONTENTS OF THIS MANUAL BEFORE
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS
OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS.
FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE
Specifications subject to change without notice.
which may occur therein
Advance AutoQuip
2 McDonald Crescent | Bassendean WA 6054
INJURY OR DEATH.
READ FIRST
DO NOT use the
machine until you read
and understand all the
dangers, warnings and
cautions in this manual.
Advertisement
Related Manuals for AAQ AutoLift AL-167261
Summary of Contents for AAQ AutoLift AL-167261
- Page 1 Note: While all due care and attention has been taken in the preparation of this document, Advance AutoQuip shall not be liable for any inaccuracies or omissions which may occur therein Advance AutoQuip 2 McDonald Crescent | Bassendean WA 6054 Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au...
-
Page 2: Table Of Contents
AutoLift 167261 Installation & Operation Manual INSTALLATION & MAINTENANCE MANUAL FOR AUTOLIFT 167261 SINGLE POST PARKING HOIST 1000Kg MAXIMUM LIFTING CAPACITY INDEX 1. Introduction …………………………………………………………… 2. Concrete Foundation …………………………………………………… 3. Dimensions …………………………………………………………… 4. Hoist Installation …………………………………………………………… 7 5. Hoist operation ………………………………………………………… 6. -
Page 3: Introduction
AutoLift 167261 Installation & Operation Manual 1. Introduction 1.1 General Information AutoLift 167261 is a single post hydraulic parking hoist. You should read the manual carefully before you operate the hoist, the hoist must be installed by a competent person, please refer to current WorkSafe regulations Australian Standards AS/NZS 1418.9 VEHICLE HOISTS . -
Page 4: Concrete Foundation
AutoLift 167261 Installation & Operation Manual Be sure to read the operating instructions before operating your hoist! Getting Ready Make sure you have made all necessary measurements to assure that your hoist will fit in your garage and accommodate the vehicle you intend to lift with it. Make sure you have enough clearance at the top, and enough width to allow walking around. -
Page 5: Dimensions
AutoLift 167261 Installation & Operation Manual Fig. 1 & 2 Dimensions... - Page 6 AutoLift 167261 Installation & Operation Manual Make sure you have someone to help you. The pieces to this hoist are big, heavy, and cumbersome. The hoist column weighs about 340Kgs by itself. It is possible for one or two people to install this hoist if they have the appropriate lifting and handling equipment, but it is definitely easier and faster if there are several people available to help manhandle the pieces into place.
- Page 7 AutoLift 167261 Installation & Operation Manual Required Tools Fork Lift to unload hoist on delivery Fork Lift and/or engine hoist for moving pieces and positioning hoist leg. You will also need a ten-foot (3048mm) length of 3/8” (9.525mm) chain 1 and 5/16” (38.4mm) wrench and socket with ratchet 1 and 1/8”...
- Page 8 AutoLift 167261 Installation & Operation Manual to deliver the hoist on an open truck When you get the packages lifted off the truck floor, simply have the driver drive his truck away from you, rather than try to remove the whole assembly from the truck. Installation You will need common hand tools that most homeowners have, like a hammer, screwdrivers and pliers, but in addition, you will need some tools that are not...
- Page 9 AutoLift 167261 Installation & Operation Manual column up from a horizontal position, lift it vertically high enough to set it on the ground . This can be accomplished with the forklift or with an engine hoist. Wrap your lifting chain around the column between the bracket of the power unit, and loop the other end of the chain (bolted together) over the forks of the forklift, or the lift hook of the engine hoist.
- Page 10 AutoLift 167261 Installation & Operation Manual F i g . 8 F i g . 9 NOTICE: If the end of the cylinder is not in the hole o the bottom palte, please put it into the hole before you lift the column upright. (Fig.10,11) F i g .
- Page 11 AutoLift 167261 Installation & Operation Manual F i g . 1 4 F i g . 1 5 After you’ve lifted the column into position, you’ll anchor it to the ground with anchor bolts. You’ll need a hammer drill and a wrench to do this, but if your hoist is being installed within 1 metre of a side wall of your garage (which it probably will), you’ll probably need a socket with a ratchet to tighten some of these bolts, because you won’t have room to maneuver a wrench.
- Page 12 AutoLift 167261 Installation & Operation Manual F i g . 1 8 F i g . 1 9 F i g . 2 0 F i g . 2 1 The next task is to position the lift frame and bolt it to the carriage (at the bottom of the lift column) with two bolts supplied.
- Page 13 AutoLift 167261 Installation & Operation Manual Put the aluminium board on the frame. F i g . 2 6 F i g . 2 7 Using the screws supplied to mount the motor pump on the side of the column( Fig. 27). Take off the red plug off the pump, screw in the elbow oil connector( Fig.
- Page 14 AutoLift 167261 Installation & Operation Manual To connect the pump to cylinder with hose and fitting. (Fig. 34 & 35) F i g . 3 4 F i g . 3 5 To fill the pump reservoir with hydraulic oil. the hydraulic oil shall be 32 grade, about 8 litres.
- Page 15 AutoLift 167261 Installation & Operation Manual OPERATING INSTRUCTIONS The hoist is very simple to operate. The button on the control unit is pushed in and held to activate the switch which turns the electric motor on (Fig. 16). The motor operates an internal pump that forces hydraulic oil into the hoist piston, which extends the roller chain and raises the hoist.
- Page 16 AutoLift 167261 Installation & Operation Manual CAUTION BE CAREFUL NOT TO RAISE THE VEHICLE SO HIGH THAT IT STRIKES THE CEILING! MAKE SURE ANTENNAS ARE REMOVED, IF NECESSARY, AND BE AWARE OF ANYTHING THAT PROTRUDES FROM THE CEILING, LIKE LIGHTBULBS, GARAGE DOOR OPENERS OR DOOR TRACKS. IT IS VERY HELPFUL HAVE A “SPOTTER”...
- Page 17 AutoLift 167261 Installation & Operation Manual MISCELLANEOUS Depending on the size of your garage, and the size of vehicles, you should take care when moving around the hoist until you get used to it being there. It is useful to spray paint the ends of the ramps and the ends of the hoist arms a bright fluorescent color to help catch your eye and avoid head bumps.
-
Page 18: Parts Drawing
AutoLift 167261 Installation & Operation Manual MOBILE SINGLE PARKING LIFT 167261 PARTS DRAWING Column and power unit Fig. 1... - Page 19 AutoLift 167261 Installation & Operation Manual Lifting frame and platform Fig. 2...
- Page 20 AutoLift 167261 Installation & Operation Manual PARTS CODE LIST ITEM CODE DESCRIPTION 1672610001 1672610002 Bolt 1672610003 1672610004 Pull ring 1672610005 Lock-release cable 1672610006 Spring 1672610007 Washer 1672610008 Bolt 1672610009 Spring 1672610010 Screw 1672610011 Bolt 1672610012 Washer 1672610013 Safty latch 1672610014 1672610015 Carriage 1672610016...
- Page 21 SAFETY OPERATING PROCEDURES Vehicle Hoist DO NOT use this machine unless the operator has been thoroughly instructed in its safe use and operation. Safety glasses must be worn at all Long and loose hair must be times in work areas. contained.
- Page 22 1000kg Single Post Parking Hoist OPERATING INSTRUCTIONS The hoist should only be operated by personnel that have been thoroughly trained in operation and maintenance of the hoist. Position the vehicle evenly on the platform, turn off the engine and apply the park brake. Note: It is important that the vehicle is evenly balanced on the hoist.
-
Page 23: Warranty
THIS WARRANTY SUPERSEDES ALL OTHER WARRANTY POLICIES PREVIOUSLY STATED AND IN ALL OTHER ADVANCE AUTOQUIP’s PRODUCT SPECIFIC LITERATURE. Advance AutoQuip 2 McDonald Crescent | Bassendean WA 6054 Ph: 08 9279 1663 | Fax: 08 9279 1667 | E: sales@aaq.net.au | W: www.aaq.net.au... -
Page 24: Commissioning Report
2. Hoist Details Model No: 2 McDonald Crescent Hoist Type: Bassendean WA 6054 Installation Date: P: 08 9279 1663 | E: sales@aaq.net.au 3. Commissioning Report Comments Safety Devices Safety devices incorporated into the design of the vehicle to AS/NZS 1418.9 Welds... - Page 25 COMMISSIONING REPORT AutoLift 167261 Installation & Operation Manual Location of Vehicle Hoist & Vehicle Clearances Vehicle hoist or any part of the load is positioned no less than 600mm away from any fixed structure Provisions have been made for effective clearances above the vehicle when the hoist is in its fully raised position.