Related Manuals for Festo CPX-AP-A-8DI-M12-5P
Summary of Contents for Festo CPX-AP-A-8DI-M12-5P
- Page 1 CPX-AP-A-8DI-M12-5P Digital input module Operating instruc- tions 8160738 2022-07 [8160740]...
- Page 2 Translation of the original instructions...
-
Page 3: Table Of Contents
Technical data ..............12 Festo — CPX-AP-A-8DI-M12-5P — 2022-07... -
Page 4: About This Document
The product labelling and the Data Matrix Code are printed on the housings of the modules. Scanning the Data Matrix Code with an appropriate device opens the Festo Internet page with documents appropriate for the product. Alternatively, the Product Key (11-digit alphanumeric code on the product labelling) can be entered in the search field è... -
Page 5: Safety
The qualified personnel have skills and experience in dealing with electrical (open-loop) control technology. Additional information – Contact the regional Festo contact if you have technical problems è www.festo.com. – Accessories and spare parts è www.festo.com/catalogue. Festo — CPX-AP-A-8DI-M12-5P — 2022-07... -
Page 6: Product Overview
Connection for inputs 4, 5 [X2] Connection for inputs 6, 7 [X3] LED displays Inscription label (optional) Fig. 1: Product design 4.1.2 LED displays Status inputs (green) Module diagnostics [MD] (green, red) Fig. 2: LED displays Festo — CPX-AP-A-8DI-M12-5P — 2022-07... -
Page 7: Connecting Elements
Carry out installation according to the "Automation system CPX-AP-A operating instructions" è 1.1 Applicable documents. Commissioning • Commission the automation system CPX-AP-A in accordance with the "Instruction manual for automation system CPX-AP-A" è 1.1 Applicable documents. Festo — CPX-AP-A-8DI-M12-5P — 2022-07... -
Page 8: Parameterisation
UINT16 – 20093 Hardware version UINT8 – 1) ro = read only; rw = read write Tab. 7: Parameter Diagnostics and fault clearance Diagnostics messages The following table contains the diagnostic messages of the module. Festo — CPX-AP-A-8DI-M12-5P — 2022-07... - Page 9 08 | 01 | 0131 AP module process The process data watchdog for the inputs timed out in the (134283569) data input watchdog module timed out – Restart AP master. Remedy – Check wiring. Diag- Error nostic status Festo — CPX-AP-A-8DI-M12-5P — 2022-07...
- Page 10 State Emergency system is in maintenance mode. No I/O function is avail- Operation able. – Restart system Remedy – Update firmware to latest version – Contact Festo service Diag- Error nostic status Tab. 8: Diagnostic messages Festo — CPX-AP-A-8DI-M12-5P — 2022-07...
-
Page 11: Led Displays
PS red light Module ramp-up not yet completed. – System communication not yet initial- ised. flashing red 2 Hz Module identification (service function) – flashing green 2 Hz Tab. 9: LED module diagnostics [MD] Festo — CPX-AP-A-8DI-M12-5P — 2022-07... -
Page 12: Technical Data
By the use of SELV/PELV circuits tion against direct and indirect contact (Safe extra-low voltage/Protected extra-low voltage) in accordance with IEC 60204-1 and IEC 60364-4-41) Electromagnetic compatibility See declaration of conformity è www.festo.com Mounting position Tab. 11: General technical data Festo — CPX-AP-A-8DI-M12-5P — 2022-07... - Page 13 [V DC] 24 ± 25% Intrinsic current consump- [mA] Typically 40 tion at nominal operating voltage 24 V from PS < 18 Diagnostics message, under- [V DC] voltage in logic supply PS Tab. 12: Power supply Festo — CPX-AP-A-8DI-M12-5P — 2022-07...
- Page 14 0 V SEN external and 0 V SEN internal Sensor power supply short circuit protection Short-circuit protection Electronic > 1.8 Trigger level Characteristic Slow-blowing Response after end of over- Automatic recovery load Tab. 13: Digital inputs Festo — CPX-AP-A-8DI-M12-5P — 2022-07...
- Page 16 Copyright: Festo SE & Co. KG 73734 Esslingen Ruiter Straße 82 Deutschland Phone: +49 711 347-0 Internet: © 2022 all rights reserved to Festo SE & Co. KG www.festo.com...