Advertisement
Note: For all rough in connections see Installation and Layout Detail Drawing.
SPECIFICATIONS
CONSTRUCTION -
Hood and tank constructed of 16 gauge 18-8 type 304 S/S. Hood unit of all welded seamless construction. S/S
frame, legs and feet. All internal castings are non-corrosive nickel alloy, bronze or S/S investment.
DOORS -
Three extra large die formed 18-8 type 304 S/S front inspection doors riding in all S/S channels. A triple ply leading edge on
the door channels made of S/S with no plastic or nylon sleeves or liners used. Two intermediate S/S door-safety stops on each door.
CONVEYOR -
Polypropylene or S/S rack sections on S/S belt with Hi-D rollers and removable rack sections. Conveyor drive sys-
tem includes large speed reducer with cut gears operating in oil bath and frictionless, trouble-free overload release system. Dishware
conveyed automatically through all washing and rinsing systems and is driven by an independent 1/2 HP motor. A stop bar sits at
the end of the unload section. This will shut off the conveyor if any ware reaches the bar. A reversing switch is provided to assist in
removing jams in the belt.
PUMPS -
Centrifugal type "packless" pump with a brass petcock drain. Construction includes ceramic seal and a balanced cast
impeller on a precision ground stainless steel shaft. All working parts mounted as an assembly and removable as a unit without
disturbing pump housing. Two 2 HP motors, 1725 RPM- wash and rinse; and 1
C-face frame, drip proof, internally cooled with ball-bearing construction.
CONTROLS -
Top-mounted control cabinet, NEMA 12 rated with heat insulation provided between hood and control cabinet, housing
motor controls and overload protection, transformer, contactors and all dishwasher integral controls. All controls safe low voltage 24 VAC.
ENERGY SAVER -
Electric photo-eye automatically operates the final rinse solenoid only when ware passes, saving water and
energy. The photo eye also activates an adjustable timer control. If no ware passes during the set time, the machine shuts down.
SPRAY SYSTEM -
Spray arms are made of 18-8 type 304 stainless steel pipe. Spray assemblies removable without the use of tools.
PREWASH -
Upper and lower manifolds. One manifold above with 3 power wash arms, each designed with 7, 6 &7 high pressure
action cleansing slots and one manifold below with 3 power wash arms, each designed with 4 high pressure action cleansing slots. The
slots are precision milled for water control, producing a fan spray. Prewash arms are fillet welded to the S/S manifold.
Upper and lower manifolds & the CrossFire ® Wash System (patented). One manifold above with 3 power wash arms designed
WASH -
with 7, 6 &7 high pressure action cleansing slots and one manifold below with 3 power wash arms, each designed with 6 high pressure
action cleansing slots. The slots are precision milled for water control producing a fan spray. Wash arms are fillet welded to the S/S
manifold. The CrossFire ® system provides 4 horizontally spraying high pressure nozzles.
RINSE -
Upper and lower manifolds. One manifold above with 3 power rinse arms, designed with 7, 6 &7 high pressure action
cleansing slots and one manifold below with 3 power rinse arms, each designed with 6 high pressure action cleansing slots. The slots
are precision milled for water control, producing a fan spray. Rinse arms are fillet welded to the S/S manifold.
FINAL RINSE -
Four nozzles above and multiple orifices below threaded into schedule 40 S/S pipes. Nozzles produce a fan spray
reducing water consumption, maximizing heat retention.
DRAIN -
Drain valves externally controlled. Overflow assembly with skimmer cap is removable without use of tools for drain line
inspection. Heaters protected by low water level control.
Tank capacity
Capacity
per hour
24 gals. (prewash)
8,812 dishes
27 gals. (wash)
500-1,000 meals
30 gals. (rinse)
Exhaust hood
Final rinse
requirement
consumption at
20 psi min.
750 CFM Load
124 gals./hr.
750 CFM Unload
3M 09/07
PRINTED IN USA
Information and specifications subject to change without notice
Electric usage
Motor size
1
hp (prewash)
1
/
2
2 hp (wash)
60 kw tanks
2 hp (rinse)
15 kw booster 40°rise
1/2 hp (conveyor)
27 kw booster 70°rise
Shipping
Peak rate
weight
drain flow
23 gals./min.
3000 lbs. (21')
CLIPPER RC
1
/
HP- 1725 RPM prewash, standard horizontal
2
Steam
consumption at
20 psi min.
218 lbs./hr tank
54 lbs./hr rem. booster 40° rise
96 lbs./hr rem. booster 70° rise
Current draw
Steam
amps
208/3/60 ................... 25.2 ..................196.8
240/1/60 ..................n/a ..................... n/a
240/3/60 ................... 22.9 ..................171.8
380/3/50 ................... 13.8 ..................107.6
480/3/60 ................... 11.4 ................... 85.6
Final rinse
peak flow
at 20 psi min.
2.1 gals./min.
Electric
w/o booster
Advertisement
