Page 1
TECHNICAL MANUAL Installation, Operation and Maintenance Instructions CADET Undercounter Dishwasher Insinger Machine Company 6245 State Road Philadelphia, PA 19135-2996 800-344-4802 Fax: 215-624-6966 www.insingermachine.com...
Page 2
Project Item Quantity CSI - 11400 Approval Date CADET Undercounter Dishwasher Three dedicated wash cycles (Dishware, Cookware, Glassware) Meets and exceeds EnergyStar 2.0 rating Extremely quiet with sound suppression lined panels. Rated at <65dB Built-in atmospheric booster with dedicated rinse ...
Page 3
HEIGHT- 13 3/16” 208/3/60 Contact Insinger Sales at 800-344-4802 for an installation drawing specific to your application. This drawing is available on the Insinger webstie at www.insingermachine.com Note: Due to product improvement we reserve the right to change information and specifications without notice.
CONTENTS SAFETY INSTRUCTIONS ................Pag. GENERAL RECOMMENDATIONS ..............Pag. HANDLING ..........................Pag. UNPACKING ..........................Pag. DISPOSAL OF PACKING MATERIAL..................Pag. TECHNICAL DATA........................Pag. INSTALLATION AND START-UP INSTRUCTIONS ........Pag. WATER CONNECTION......................Pag. ELECTRICAL CONNECTION ....................Pag............................Pag. C3.2 Power supply 208 V 3ph ....................Pag. C3.3 Connections provided for energy control.................
SAFETY INSTRUCTIONS To reduce the risk of fire, electrical shock, or injury when using your dishwasher, please follow these basic pre- cautions including the following: • Read all instructions before using your dishwasher. • This Manual does not cover every possible condition and situation that may occur. Use common sense and caution when installing, operating and maintaining this appliance.
GENERAL RECOMMENDATIONS HANDLING CAUTION Use suitable means to move the appliance: a lift truck or CAREFULLY READ THE INSTALLATION OPERA- fork pallet trucks (the forks should reach more than hal- TING AND MAINTENANCE INSTRUCTIONS BEFORE fway beneath the appliance). INSTALLING THIS APPLIANCE.
TECHNICAL DATA MODEL CADET CDT-1 Supply voltage: 208V, 1ph, 60Hz 33amp field upgrade to 208V, 3ph 60Hz 20amp Total Watts 6.85 kW Booster heating elements 6.0 kW Tank heating elements 2.2 kW...
Page 9
Figure 4 Legend Figure 4 WI - Water inlet pipe with 3/4”dia/19mm fittings D - Outlet pipe 11/16” ID /18 mm (*). EI - Power supply XD - Detergent connection EQ - Equipotential (Ground) screw XR - Rinse aid connection (*) - Only for model with drain pump...
Connect the energy peak controller across terminals 11 WARNING and 12. Before servicing unit switch off power at the main circuit breaker and place a red CAUTION tag on the breaker to indicate work is A normally open (n.o.) contact of the con- being done on that circuit.
DETERGENT/RINSE-AID DISPENSERS AND SETTINGS If the appliance is connected to a water softener or osmotic device, contact the detergent supplier for the specific product. Peristaltic dispensers (rinse-aid and detergent) require periodic maintenance. The internal hose of the rinse-aid dispenser should undergo periodic maintenance (at least once or twice a year).
Amount of rinse-aid during the cycle: LEGEND Increase DETERGENT PRIMING Decrease RINSE AID PRIMING Setting the activation time: Confirm or select next parameter DETERGENT PRIMING C6.1 Sequential start RINSE AID PRIMING Press the indicated buttons simultaneously for 5 seconds: Exit from programming mode: ...
C6.2 Changing the detergent/rinse-aid type Otherwise, the mixing of different types of deter- gent/rinse-aid will cause crystallisation, which may result If changing to a different detergent/rinse-aid type in a breakdown of the dosing pump. Failure to observe (even one by the same manufacturer), you must rinse this condition will invalidate the warranty and product lia- the suction and pressure hoses with fresh water before bility.
The word “FILL” is shown on the display during the The appliance is then ready for use: entire filling and heating stage • Open the door. • Insert the rack containing the dirty dishes. Close the door and select the suitable wash cycle; the ...
D3.1 Type of racks and loading • After a few minutes, 3 beeps indicate the end of the cleaning cycle and “END” blinks on the display: • YELLOW rack: for 18 plates with maximum diameter of 240 mm. • Switch off the dishwasher by pressing “A”...
Do not wash the appliance using direct or high-pressure water jets. To reduce the emission of pollutants into the environment, clean the appliance (externally and where necessary internally) with products having a biodegrada- After a few minutes, 3 beeps indicate the end of the cle- bility of over 90%).
The wash cycle duration is 10 minutes. At the end of the NOTICE: Using any parts other than genuine factory cycle the dishwasher emits a series of beeps and “END” manufactured parts relieves the manufacturer of all war- blinks on the display. ranty and liability.
Falling from The operator intervenes on the above machine using unsuitable systems to access the upper part (e.g. rung ladders, or climbs on it). Tipping of During maintenance on the machine loads packing containing machine with the use of unsuitable accessories or lifting systems or with load unbalanced.
Page 20
Insinger Machine Company 6245 State Road Philadelphia, PA 19135-2996 800-344-4802 Fax: 215-624-6966 www.insingermachine.com The Manufacturer reserves the right to modify the appliances presented in this publication without notice. El Constructor se reserva el derecho de modificar sin previo aviso, las características de los aparatos presentados en esta publicación.