New Holland 499 Operator's Manual page 120

Reel
Type
Effective tine tip speed
Tine bar sweeps per minute
Diameter (maximum)
Length (at longest point in front of reel)
(at discharge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spider angle relative to tube axis
Tine bar bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reel cross bearings . . . . . . . . . . . . . . . . . . . . . . . . . .
Reel shaft bearings . . . . . . . . . . . . . . . . . . . . . . . . . .
Cam follower bearings
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive reduction bearings
Cutter Bar
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guard angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cutting height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sickle Drive
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearings
Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting rods . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrier bearing
(connects left and right gearboxes)
Rocker arm pivots
Belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Push Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conditioner
Roll length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roll diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roll type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roll Drive Gearbox
Gears . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 - SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
Rolareel™
7.7 km/hr – 12.7 km/hr (4.8 MPH – 7.9 MPH)
(in direction of travel) 6.5 km/hr – 10.7 km/hr
(4.0 MPH – 6.6 MPH) w/speed reduction kit
161 to 265 136 to 223 w/speed reduction
1105 mm (43–1/2")
3804 mm (149–3/4")
2639 mm (103–7/8")
0.61 rad. (35 degrees)
Ball bearings
Sealed-for-life ball bearings
(2) Sintered bronze bushings
(2) Sealed-for-life ball bearings
Sealed-for-life ball bearings
RC 40 roller chain reduction to "HC" section V-belt
Needle bearings
3734 mm (12'3")
Adjustable 4 degrees, 7 degrees, or 10 degrees
(4 degrees to 10 degrees optional hydraulic
guard angle adjustment kit)
Twin forged steel, heat treated (PN 219191)
Adjustable 32 mm – 159 mm (1-1/4" – 6-1/4")
Two opposing knife assemblies with underserrated
sections 3 mm (0.120") thick
Bevel gearbox driven crankshaft drive rocker arm
through a connecting rod. Knife head pivots on
rubber bushing. Gearboxes are driven by 3-HB
V-belt drive from conditioner
850 cycles/minute
76 mm (3")
Tapered roller
Tapered roller
Needle bearings
Rubber bushing
Tapered roller
Tubular steel, adjustable height
2794 mm (110")
264 mm (10-3/8")
Molded rubber with intermeshing chevron design lugs
665 RPM, 33 km/hr (20.5 MPH) at OD
Sealed ball bearings
Gear-driven, U-joint drive to upper roll,
straight shaft to lower roll
Heat-treated 6-pitch spur gears
Tapered roller
7-2