Table of Contents
Advertisement
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Setting up the appliance
Please note!
•
Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
•
You should customise water hardness as soon as possible
following the instructions in the section "Setting water
hardness" on page 20.
1. Insert the power cord (C8) connector into the socket at the
back of the appliance (A19) and connect the appliance to
the mains electricity supply (fig. 1). Make sure the main
switch (A20) at the back of the appliance is pressed (fig. 2).
2. Remove the water tank (A16- fig. 3), open the lid (A18- fig.
4), fill to the MAX line with fresh water (fig. 5); replace the
lid and put the tank back in the appliance.
You must first choose the language by moving backwards and
forwards with the < (B4) or > (B8) (fig. 9) button, or waiting
until the languages scroll through on the display (B13) at inter-
vals of about 3 seconds:
3. When "English" appears, press the
for a few seconds until "English set" is displayed.
Follow the instructions indicated on the appliance display:
4. "INSERT WATER SPOUT": Check that the hot water spout (C6)
is inserted on the connection nozzle (A8) and place a con-
tainer holding a minimum of 100 ml underneath (fig. 7).
5. "HOT WATER Press OK" is displayed;
6. Press the
button to confirm (fig. 6). The appliance de-
livers water from the spout then goes off automatically.
The coffee machine is now ready for normal use.
Please note!
•
When setting up the appliance, you need to make 4-5 cups
of coffee or 4-5 cappuccinos before the appliance starts to
give satisfactory results.
•
When making the first 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
•
To enjoy your coffee even more and improve the perfor-
mance of your appliance, we recommend installing a water
softener filter (C4) as described in the section "WATER SOF-
TENER FILTER" (page 21). If your model is not provided
with a filter, you can request one from De'Longhi Customer
Services.
TURNING THE APPLIANCE ON
Before turning the appliance on, make sure the main switch
(A20) is pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
During rinsing, a little hot water comes out of the coffee spouts
(A7) and is collected in the drip tray (A12) underneath. Avoid
contact with splashes of water.
•
When heating is complete, the message changes to "RINSING".
As well as heating the boiler, this also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message indicating
the taste and quantity of coffee appears.
TURNING THE APPLIANCE OFF
Whenever the coffee machine is turned off after being used to
make coffee, it performs an automatic rinse cycle.
During rinsing, a little hot water flows from the coffee spouts
button (B7- fig. 6)
(A7). Avoid contact with splashes of water.
•
•
If you will not be using the appliance for some time, unplug
from the mains socket:
•
•
Never press the main switch while the appliance is on.
MENU SETTINGS
Rinsing
Use this function to deliver hot water from the coffee spout (A7)
and from the cappuccino maker/hot water spout (C6), if insert-
ed, to clean and heat the appliance's internal circuit.
Place a container with a minimum capacity of 100 ml under the
cappuccino maker/hot water spout (fig. 7).
To enable the function, proceed as follows:
10
Please note!
Danger of burns!
To turn the appliance on, press the
8). The message "Heating up, Please wait" is displayed.
Danger of burns!
To turn the appliance off, press the
8).
The message "Turning off Please wait" is displayed, then
the appliance performs a rinse cycle and goes off (standby).
Please note!
first turn the appliance off by pressing the
release the main switch (A20) at the back of the appliance
(fig. 2).
Important!
button (B1- fig.
button (B1- fig.
button;
Advertisement
Table of Contents
Troubleshooting
