CONTENTS Making LONG coffee using pre-ground coffee ....13 Customising the LONG coffee quantity ......13 INTRODUCTION ..........7 MAKING CAPPUCCINOS AND MILK BASED Symbols used in these instructions ........7 COFFEES ............13 Letters in brackets ............7 Troubleshooting and repairs ..........7 Filling and attaching the milk container ......
INTRODUCTION • Unplug directly from the plug only. Never pull the power cable as you could damage it. Thank you for choosing this automatic espresso and cappuccino • To disconnect the appliance completely, unplug it from the machine. mains socket. We hope you enjoy using your new appliance.
Description of the control panel This is a household appliance only. It is not intended to be used in: (page 2 - B ) A number of buttons on the panel have a double function. This is • staff kitchen areas in shops, offices and indicated in brackets in the description.
Installing the appliance 3. “FILL TANK”: extract the water tank (fig. 4), open the lid (fig. 5), fill to the MAX line with fresh water (fig. 6); close Important! the lid again and then replace the tank. When you install the appliance, you should respect the fol- 4.
1. Press the MENU/ESC button to enter the menu; Danger of burns! 2. Press < or > (fig. 9) until “Adjust time” is displayed; During rinsing, a little hot water flows from the coffee spouts. 3. Press the OK button (fig. 10): the hours flash; Avoid contact with splashes of water.
Proceed as follows: 1. Press the MENU/ESC button to enter the menu; Setting the language 2. Press < or > (fig. 9) until “Cup warmer” is displayed; To modify the language of the display, proceed as follows: 3. Press the OK button: “Enable?” or “Disable?” will be 1.
MAKING COFFEE Please note! Selecting the coffee taste The grinding adjustment dial must only be turned when the The appliance is set by default to make coffee with a standard coffee mill is in operation. taste. You can also choose one of these tastes: If the coffee is delivered too slowly or Extra-mild taste not at all, turn one click clockwise to-...
Press OK”. Add one level measure of pre-ground coffee and press Please note! • Various alarm messages could be displayed while using Coffee delivery resumes and the progress bar gradually fills as the machine (FILL TANK, EMPTY GROUNDS CONTAINER, preparation progresses. etc.).
6. Attach the milk container to the connection nozzle and 4. Press < or > until the required drink is displayed (MILK, push as far as it will go (fig. 23). The machine emits a beep CAFFELATTE, ESPRESSO MACCHIATO or MY MILK). 5.
Programming the quantity of coffee and milk DELIVERING HOT WATER AND STEAM in the cup for the CAPPUCCINO, FLAT WHITE and Important! Danger of burns. LATTE buttons Never leave the machine unsupervised while delivering hot The appliance is set by default to automatically deliver standard water or steam.
Tips for using steam to froth milk machines, you need not use chemical products to clean the machine. • When choosing the size of the container, bear in mind that • None of the components of the appliance can be washed in the liquid doubles or triples in volume.
Cleaning the inside of the coffee machine 2. Extract the water tank (fig. 4). 3. Open the infuser door (fig. 35) on the right side of the Danger of electric shock! appliance. Before cleaning internal parts, the machine must be turned off (see “Turning off”) and unplugged from the mains power sup- ply.
6. Check that the intake tube and spout are not clogged with milk residues. 7. Replace the dial (in correspondence to the word “INSERT”), spout and milk intake tube. 8. Place the lid back on the milk container. Cleaning the hot water/steam connection nozzle Each time you prepare milk, clean the connection nozzle with a sponge to remove milk residues from the gaskets (fig.
Avoid contact with splashes of water. 9. Press the OK button to confirm that you have added the solution. The descale programme automatically performs a series of rinses and pauses to remove limescale deposits from inside the machine. “Descale underway” is displayed. The descale programme starts, and descaler comes out of the water spout.
1. Extract the tank and exhausted filter; 0,5 L 2. Take the new filter out of its packet and proceed as illustra- ted in points 2-3-4-5-6-7 in the previous section; 3. Position a container with a minimum capacity of 500 ml under the hot water spout;...
DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE SOLUTION FILL TANK Insufficient water in the tank. Fill the tank with water and/or insert it cor- rectly, pushing it as far as it will go until it clicks into place. EMPTY GROUNDS CONTAINER The grounds container (A10) is full. Empty the grounds container and drip tray, clean and replace (fig.
GENERAL ALARM The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly, as described in the section “Cleaning”. If the message is still displayed after cleaning, contact a Customer Experience. EMPTY CIRCUIT, FILL CIRCUIT The water circuit is empty Ensure the water spout is inserted.
Coffee does not come out of one of the The spouts are blocked. Clean the spouts with a toothpick (fig. 34). spouts. The appliance does not come on. The power cable is not plugged in Plug the cable fully into the socket on the back properly.
ELECTRICAL CONNECTION (UK ONLY) Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the proce- dure outlined below.