Descaling; Install Filter; Replacing The Limescale Filter (If Installed); Adjust Time - DeLonghi ECAM45.76 Series Instructions For Use Manual

1. Press the MENU/ESC (B14) button to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Rinsing" is displayed;
3. Press the OK button (B12- fig. 10): the message "Confirm?"
is displayed;
Danger of burns!
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the OK button. "RINSING Please wait" is displayed;
5. After a few seconds, hot water is delivered first from the
cappuccino maker/hot water spout (if inserted) which
heats the appliance's internal circuit. "RINSING" is dis-
played, together with a progress bar which fills gradually
as preparation proceeds.
6. To stop the process press any button or wait for delivery of
water to stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, we
strongly recommend, when switching on the appliance,
performing 2/3 rinses before using it;
• After cleaning, it is normal for the grounds container (A10)
to contain water.

Descaling

For instructions on descaling, see page 21.

Install filter

For Instruction for use on how to install the filter, see the section
"Water softener filter" (page 21).

Replacing the limescale filter (if installed)

For Instruction for use on how to replace the filter, see the sec-
tion "Replacing the filter" (page 21).

Adjust time

To adjust the time on the display (B13), proceed as follows:
1. Press the MENU/ESC (B14) button to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Adjust time" is
displayed;
3. Press the OK button (B12- fig. 10): the hours flash on the
display;
4. Press < or > to change the hour;
5. Press the OK button to confirm. The minutes flash;
6. Press < or > to change the minutes;
7. Press the OK button to confirm.
The time is set: press the MENU/ESC button to exit the menu.

Auto-start

You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC (B14) button to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Auto-start" is displayed;
3. Press the OK button (B12- fig. 10). "Enable?" is displayed;
4. Press the OK button to confirm;
5. Press < or > to choose the hour;
6. Press the OK button to confirm;
7. Press < or > to change the minutes;
8. Press the OK button to confirm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been confirmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the OK button. "Disable?" is displayed;
3. Press the OK button to confirm.
The symbol is no longer displayed.

Auto-off (standby)

Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press the MENU/ESC (B14) button to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Auto-off" is displayed;
3. Press the OK button (B12- fig. 10).
4. Press < or > until the required operating time (15 or 30
minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to confirm;
6. Press the MENU/ESC button to exit the menu.
Auto-off is programmed.

Cup warmer

This function enables the cup warmer to be enabled or disabled.
Proceed as follows:
1. Press the MENU/ESC (B14) button to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Cup warmer" is
displayed;
3. Press the OK button (B12- fig. 10). "Enable?" or "Disable?"
is displayed;
4. Press the OK button to enable or disable the cup warmer
(the message "Cup warmer Enabled" indicates that it is
active);
11