Advertisement
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket - with the obvious consequent danger.
N.B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use.
the wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. do not forget to tighten the mains lead clamp on the plug. if your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. after replacement of a fuse in the plug, the fuse cover must be refitted. if the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. always state this colour when ordering a replacement fuse cover. only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted. This appliance conforms to the Norms eN 55014 regarding the suppression of radio interference.
this appliance must be earthed
Thank you for choosing the eCam 22.320 automatic coffee and cappuccino maker.
We hope you enjoy using your new appliance.
Please take a few minutes to read these instructions for use.
This will avoid all risks and damage to the appliance.
Important warnings are identified by these symbols. it is absolutely vital that these warnings are respected.
Failure to observe the warning may result in life threatening injury from electrical shock.
Failure to observe the warning may result in injury or damage to the appliance.
Danger of scalding!
Failure to observe the warning may result in scalding or burns.
Please note:
This symbol indicates important advice or information for the user.
The letters in brackets refer to the caption in the description of the appliance.
In the event of problems, first try and resolve them by reading the information given in the sections on "messages displayed" and "Troubleshooting".
If this does not resolve the problem or should you require further information, you should consult Customer Services by calling the number given on the annexed "Customer Services" leaflet. if your country is not among those listed on the sheet, call the number given in the guarantee.
If repairs are required, contact de'longhi Customer Services only. The addresses are given in the guarantee leaflet provided with the machine.
This is an electrical appliance and may cause electrical shocks.
You should therefore follow these safety warnings:
This appliance produces hot water and steam may form while it is in operation.
Avoid contact with splashes of water or hot steam.
This appliance is designed and made to prepare coffee and heat drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from improper use of the appliance.
This is a household appliance only.
It is not intended to be used in:
Read these instructions carefully before using the appliance.
Please note:
Keep these instructions.
If the appliance is passed to other persons, they must also be provided with these instructions.
A1 Control panel
A2 Grinding dial
A3 Cup shelf
A4 Beans container lid
A5 Pre-ground coffee funnel lid
A6 Pre-ground coffee funnel
A7 Beans container
A8 Main switch
A9 Socket for power cable connector
A10 Water tank
A11 Infuser door
A12 Infuser
A13 Coffee spout (adjustable height)
A14 Coffee grounds container
A15 Condensate tray
A16 Cup rest
A17 Drip tray water level indicator
A18 Drip tray
A19 Cappuccino maker
A20 Cappuccino/hot milk ring
A21 Steam/hot water knob
A number of buttons on the panel have a dual function. This is indicated in brackets in the description.
B1. Display: guides the user in using the appliance
B2. Button: turns the appliance on and off
B3. MENU button to access the menu (When in the settings MENU this button functions as an ESC button to exit the function selected and go back to the main menu)
B4. button to deliver steam to make hot milk-based drinks
B5. button: to perform a rinse cycle.
(When in the settings MENU this button functions as a > button to scroll forward)
B6. button: to make coffee using pre-ground coffee.
(When in the settings MENU this button functions as an OK button to confirm selection made)
B7. Aroma selection button: press to select coffee taste
B8. Button: to make 1 cup of short espresso coffee
B9. Button: to make 2 cups of short espresso coffee
B10. LONG button: to make 1 cup of loNg coffee
B11. Button: to make 1 cup of long espresso coffee
B12. Button: to make 2 cups of long espresso coffee
C1. Measure
C2. Descaler
C3. Water softener filter (certain models only)
C4. Total hardness Test indicator paper
C5. Power cable
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged. Contact de'longhi Customer Services.
When you install the appliance, you should observe the following safety warnings:
Check that the mains power supply voltage corresponds to that indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10a only.
If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualified professional.
Please note:
The coffee machine is now ready for normal use.
Please note:
Please note:
Before turning the appliance on, make sure the main switch at the back of the appliance is pressed down (fig. 2).
Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only once this cycle is complete.
Danger of scalding!
During rinsing, a little hot water comes out of the coffee spouts and is collected in the drip tray underneath. avoid contact with splashes of water.
When the heating up is complete, the message changes to "rinsing". By circulating hot water, the appliance heats both the boiler and the internal circuits.
The appliance is at temperature when the message indicating the taste and quantity of coffee is displayed.
Each time the appliance is turned off, it performs an automatic rinse cycle which cannot be interrupted.
Danger of scalding!
During rinsing, a little hot water comes out of the coffee spouts.
Avoid contact with splashes of water.
To turn the appliance off, press the button (fig. 6). The appliance performs a rinse cycle then turns off (stand-by).
Please note:
if you will not be using the appliance for some time, unplug it from the mains socket:
Never press the main switch while the appliance is switched on.
When you access the settings menu by pressing the meNu button, the following menu items can be selected: descale, adjust time, autooff, auto-start, Set temperature, energy saving, Water hardness, Set language, install filter, replace filter, default values, Statistics.
To adjust the time on the display, proceed as follows:
The time is set: press MENU to exit menu.
Auto-off can be set so that the appliance turns off after 15 or 30 minutes, or after 1, 2 or 3 hours.
The auto-off is set. press MENU to exit menu.
You can set the auto-start time in order to have the appliance ready for use at a certain time (for example in the morning) so you can make coffee immediately.
Please note:
To enable this function you must ensure the time is set correctly.
Once the time has been confirmed, activation of auto-start is indicated by the symbol which is displayed alongside the time and under the auto-start item in the menu.
To disable the function:
The symbol is no longer displayed.
if you want to modify the temperature of the water used to make the coffee (low, medium, high), proceed as follows:
The temperature is set. press MENU to exit menu.
Гse this function to enable or disable energy Saving. When enabled, the function reduces energy consumption in compliance with eu regulations. When energy saving mode is enabled an asterisk appears under "energy saving" in the menu.
Then press MENU to exit menu.
When the function is enabled, if the machine is not used for about 1 minute "energy saving" is displayed.
Please note:
When in energy saving mode, a few seconds may elapse before the first coffee is delivered as the appliance must heat up again.
To change the language on the display, proceed as follows:
The language is set. press MENU to exit menu.
This resets all menu settings and programmed quantities back to the default values (with the exception of the language which remains as set).
This displays statistics relating to the machine. To display, proceed as follows:
The appliance is set by default to make coffee with a standard taste. you can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
To change the taste, press the button repeatedly (fig. 7) until the required taste is displayed.
The appliance is set by default to automatically make the following quantities of coffee:
To change the quantity of coffee the appliance delivers automatically into the cup, proceed as described below:
The machine is now reprogrammed with the new quantities.
The coffee mill is set by default to prepare coffee correctly and should not require regulating initially.
However, if after making the first few coffees you find that the coffee is either too weak and not creamy enough or delivery is too slow (in drops), this can be corrected by adjusting the grinding dial (fig. 8).
Please note:
The grinding dial must only be turned while the coffee mill is in operation.
If the coffee is delivered too slowly or not at all, turn one click clockwise. For fuller bodied creamier coffee, turn one click anticlockwise (do not turn more than one click at a time otherwise the coffee could be delivered in drops).
These adjustments will only be evident after at least 2 cups of coffee have been delivered.
If this adjustment does not obtain the desired result, turn the dial another click.
For hotter coffee, you should:
Do not use caramelised or candied coffee beans as they could stick to the coffee mill and damage it.
Once the coffee has been made, the appliance is ready to be used again.
Please note:
Please note:
For hotter coffee, see the section "Tips for a hotter coffee".
Please note:
if you use pre-ground coffee, you can only make one cup of coffee at a time.
LONG coffee can be made using either coffee beans or preground coffee.
Follow the directions above to prepare the machine and press the LONG button.
Danger of scalding!
Be careful of scalding as steam escapes during preparation of these drinks.
Please note:
For a richer denser froth, use skimmed or partially skimmed milk at refrigerator temperature (about 5°C). To avoid milk with poor froth or large bubbles, always clean the cappuccino maker as described in the section "Cleaning the cappuccino maker after use".
Danger of scalding!
Stop steam delivery before removing the container with the frothed milk to avoid burns caused by splashes of boiling milk.
To make hot milk without froth, proceed as described in the above section, making sure the cappuccino/hot milk ring of the cappuccino maker is positioned upwards in the "HOT MILK" position.
Clean the cappuccino maker each time you use it to avoid the build-up of milk residues or blockages.
Danger of scalding!
When cleaning the cappuccino maker, a little hot water is delivered. avoid contact with splashes of water.
Danger of scalding!
Never leave the machine unsupervised while hot water is being delivered. as shown below, stop delivery of hot water when the cup is full.
The cappuccino maker becomes hot while hot water is being delivered and must be held by the black ring only.
Please note:
If "energy Saving" mode is active, you may have to wait a few seconds before the hot water is delivered.
The following parts of the machine must be cleaned regularly:
When "EMPTY GROUNDS CONTAINER" is displayed, the grounds container must be emptied and cleaned.
Unless you clean the grounds container, the above message will continue to be displayed and the appliance cannot be used to make coffee. To clean (with the machine turned on):
When removing the drip tray, the grounds container must be emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the grounds container may fill up more than expected and clog the machine.
If the drip tray is not emptied regularly, the water could overflow and seep inside or around the machine. This could damage the machine, the surface it rests on or the surrounding area.
The drip tray is fitted with a floating level indicator (red) showing the level of water it contains (fig. 22). Before the indicator protrudes from the cup rest, the drip tray must be emptied and cleaned.
To remove the drip tray:
Before cleaning internal parts, the machine must be turned off (see "Turning off") and unplugged from the mains power supply. Never immerse the machine in water.
Check regularly (about once a month) that the pre-ground coffee funnel (a6) is not blocked.
If necessary, remove coffee deposits with a brush.
The infuser (a12) must be cleaned at least once a month.
The infuser may not be extracted when the machine is on.
RINSER WITH WATER ONLY
NO WASHING UP LIQUID - NO DISHWASHER
Do not use washing up liquid to clean the infuser as it may damage it.
Please note:
If the infuser is difficult to insert, before insertion, squeeze the two levers shown in the figure to make it smaller.
Descale the machine when the message "deSCale" flashes on the display.
Descaler contains acids which may irritate the skin and eyes.
It is essential that you observe the manufacturer's safety warnings indicated on the descaler packet and the warnings relating to the procedure to follow in the event of contact with the skin and eyes.
Please note:
Use descaler recommended by de'longhi only. Failure to descale the appliance as described above also invalidates the guarantee.
Danger of scalding!
Hot water containing acid is delivered from the cappuccino maker. avoid contact with splashes of water.
After about 30 minutes, the message "FILL TANK!" is displayed. The appliance is now ready for rinsing through with clean water.
The DESCALE message is displayed after a period of operation established according to the water hardness
The machine is set by default for a hardness value of 4.
The machine can also be programmed according to the hardness of the mains water in the various regions so that the machine needs to be descaled less often.
The machine is now reprogrammed with the new water hardness setting. press the MENU button again to exit menu.
Certain models are fitted with a water softener filter. if this is not the case with your model, you are recommended to purchase one from authorised de'longhi Customer Services.
To use the filter correctly, follow the instructions below.
Please note:
The filter lasts about two months if the appliance is used normally. if the coffee machine is left unused with the filter installed, it will last a maximum of three weeks.
The filter is now active and indicated by an asterisk displayed in the menu under the item "install filter". you can now use the coffee machine.
When the message "replace filter" is displayed or after two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter.
if you want to continue use the appliance without the filter, you must remove it and notify the appliance of its removal. proceed as follows:
Voltage: | 220-240 v~ 50/60 hz max. 10A |
Absorbed power: | 1450W |
Pressure: | 15 bar |
Max. capacity water tank: | 1,8 litres |
Size: lxhxd: | 238x345x430 mm |
Cable length: | 1,15 m |
Weight: | 9,1 Kg |
Max. capacity beans container: | 250 g |
The appliance complies with the following eu directives:
In compliance with european directive 2002/96/eC, the appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.
MESSAGE DISPLAYED | POSSIBLE CAUSE | SOLUTION |
FILL TANK | Insufficient water in the tank | Fill the tank with water and/or insert it correctly, pushing it as far as it will go until it clicks into place (fig. 4). |
EMPTY GROUNDS CONTAINER | The grounds container (a13) is full. | Empty the grounds container and drip tray, clean and replace (fig. 23). When removing the drip tray, the grounds container must be emptied, even if it contains few grounds. If this is not done, when you make the next coffees, the grounds container may fill up more than expected and clog the machine. |
GROUND TO FINE ADJUST MILL alternating WITH TURN STEAM KNOB | The grinding is too fine and the coffee is delivered too slowly or not at all. | Repeat coffee delivery and turn the grinding dial (fig. 8) one click clockwise towards "7" while the coffee mill is in operation. if after making at least 2 coffees delivery is still too slow, repeat the correction procedure, turning the grinding dial another click until delivery is correct (see the section "adjusting the grinder"). if the problem persists, turn the steam knob to the i position and let some water run from the cappuccino maker. |
INSERT GROUNDS CONTAINER | after cleaning, the grounds container has not been replaced. | Remove the drip tray and insert the grounds container. |
ADD PRE-GROUND COFFEE | The "pre-ground coffee" function has been selected without placing any pre-ground coffee in the funnel. | Place pre-ground coffee in the funnel or deselect the preground function. |
DESCALE | The machine must be descaled. | The descaling procedure described in the "descaling" section needs to be performed as soon as possible. |
LESS COFFEE | Too much coffee has been used. | Select a milder taste or reduce the quantity of pre-ground coffee. |
FILL BEANS CONTAINER | The coffee beans have run out. | Fill the beans container. |
The pre-ground coffee funnel is clogged. | Empty the funnel with the help of a brush, as described in the section "Cleaning the pre-ground coffee funnel". | |
INSERT INFUSER ASSEMBLY | The infuser has not been properly replaced after cleaning. | Insert the infuser as described in the section "Cleaning the infuser". |
INSERT TANK | The tank is not correctly in place. | Insert the tank correctly and press as far as it will go. |
GENERAL ALARM | The inside of the appliance is very dirty. | Clean the inside of the appliance thoroughly, as described in the section "Cleaning". if the message is still displayed after cleaning, contact de'longhi Customer Services. |
REPLACE FILTER | The water softener filter has been used up. | Replace the filter or remove it as described in the section "Water softener filter" |
EMPTY CIRCUIT FILL CIRCUIT alternating WITH HOT WATER PRESS OK | The water circuit is empty. | Press OK to deliver water from the spout until it flows out normally. |
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact customer services.
PROBLEM | POSSIBLE CAUSE | SOLUTION |
The coffee is not hot | The cups were not preheated. | Warm the cups by rinsing them with hot water. (N.B. you can use the hot water function). |
The infuser has cooled down because 2/3 minutes have elapsed since the last coffee was made. | Before making coffee, heat up the infuser by pressing the ![]() | |
A low coffee temperature is set. | Set a high coffee temperature in the menu. | |
The coffee is weak or not creamy enough | The coffee is ground too coarsely. | Turn the grinding dial one click anticlockwise towards "1" while the coffee mill is in operation (fig. 8). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after 2 coffees have been made (see the section "adjusting the grinder"). |
The coffee is unsuitable. | Use pre-ground coffee for espresso machines. | |
The coffee is delivered too slowly or in drops | The coffee is ground too finely. | Turn the grinding dial one click clockwise to "7" while the coffee mill is in operation (fig. 10). Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after 2 coffees have been made (see the section "adjusting the grinder"). |
Coffee does not come out of one or both spouts. | The spouts are blocked. | Clean the spouts with a toothpick. |
The frothed milk has large bubbles | The milk is not cold enough or is not semi-skimmed. | you should ideally use skimmed or semi-skimmed milk at refrigerator temperature (about 5°C). if the result is not as you wished, try changing brand of milk. |
The milk is not frothed | Cappuccino maker is dirty. | Clean as described in the section "Cleaning the cappuccino maker after use". |
The ring on the cappuccino maker is NOT in the cappuccino position. | Place the ring in the CAPPUCCINO position. | |
Steam delivery stops | a safety device stops steam delivery after 3 minutes. | Wait, and then enable the steam function again. |
The appliance does not turn on | it is not plugged into the mains socket. | Plug into the mains socket. |
The main switch (A8) is not turned on. | Push the main switch in the I position (fig. 1). |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download DeLonghi Magnifica S ECAM 22.320.SB Automatic Coffee Maker Manual
Advertisement
Need help?
Do you have a question about the ECAM 22.320.SB and is the answer not in the manual?
Questions and answers