Download Print this page

Advertisement

Cisco IAD2430 Series Integrated Access
Devices Hardware Installation Guide
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-4234-06

Advertisement

Chapters

   Related Manuals for Cisco IAD2430 Series

   Summary of Contents for Cisco IAD2430 Series

  • Page 1

    Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-4234-06...

  • Page 2

    MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc.

  • Page 3: Table Of Contents

    Port Numbering Conventions Specifications Software Elements Configuration Connections Configuration Methods Automated Configuration Manual Configuration Interfaces and Service Capabilities Configuration Options OL-4234-06 viii viii Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide C O N T E N T S...

  • Page 4

    Rack-Mounting the Chassis Mounting Screws Attaching the Brackets Installing the Cisco IAD2430 Series IADs in a Rack Wall-Mounting the Chassis Wall-Mounting the Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IADs Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06...

  • Page 5

    Connecting the Analog Voice Interface to a Distribution Panel Cable Procedure Connecting the Digital Voice Port to a T1/E1-PBX Cable Procedure Ports, Connectors, and Pinouts OL-4234-06 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Wall-Mounting the Cisco IAD2435 IADs...

  • Page 6

    Connecting to a Remote ASCII Terminal Connecting Backup Power Connecting a Backup Battery to a DC-Powered IAD Connecting an Uninteruptible Power Supply UPS to an AC-Powered Cisco IAD2430 Series IAD Powering On Cisco IAD2430 Series IADs C H A P T E R...

  • Page 7

    This publication is designed for people who have some experience installing networking equipment such as routers, servers, and switches. The person installing Cisco IAD2430 series integrated access devices (IADs) should be familiar with networks and telephony equipment as well as with electronic circuitry and wiring practices and have experience as an electronic or electromechanical technician.

  • Page 8: Safety Warnings

    A warning symbol precedes each warning statement. To see translations of the warnings that appear in this publication, see the Cisco IAD2430 Series Regulatory Compliance and Safety Information document that accompanied your router or go to the following URL: http://www.cisco.com/en/US/products/hw/gatecont/ps887/prod_installation_guides_list.html...

  • Page 9: Warning Definition

    Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewusst. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise sind im Lieferumfang des Geräts enthalten. Hinweis BEWAHREN SIE DIESE SICHERHEITSANWEISUNGEN AUF Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06...

  • Page 10

    Se översättningarna av de varningsmeddelanden som finns i denna publikation, och se de översatta säkerhetsvarningarna som medföljer denna anordning. OBS! SPARA DESSA ANVISNINGAR Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06...

  • Page 11

    Preface Safety Warnings Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06...

  • Page 12

    Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide OL-4234-06...

  • Page 13

    Preface Safety Warnings Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide xiii OL-4234-06...

  • Page 14

    Statement 1043 Product Serial Number Location The serial number label for the Cisco IAD2430 series routers (Cisco IAD2430 through Cisco IAD2432) is located on the back of the chassis, near the compliance label. The size of the serial number label is 0.25 x 1 inch (0.635 x 2.54 centimeters).

  • Page 15

    IA D 24 31 -8 FX S A A A N N N N X X X X Serial Number Location on Cisco IAD2435-8FXS Routers Cisco 11 character label SN: AAANNNNXXXX Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Accessibility...

  • Page 16: Related Documentation

    • Cisco IAD2430 Series Integrated Access Device—Release Notes 1. See the modular reference publications that correspond to the Cisco IOS software release installed on your Cisco IAD2430 series integrated access device. Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and...

  • Page 17

    • Overview The Cisco IAD2430 series IADs aggregate multiple channels of data and voice or fax user-side traffic for transport over single or multiple WAN uplinks. Voice or fax traffic is transported by VoIP or by Voice over Asynchronous Transfer Mode (VoATM). All platforms support Media Gateway Control Protocol (MGCP), the signaling protocol H.323, and Session Initiation Protocol (SIP).

  • Page 18: Chapter 1 Overview Of Cisco Iad2430 Serie Iad

    • External/internal flash memory • The Cisco IAD2430 series IADs can be mounted in a rack, on a wall, or a desktop. There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with Warning the same or equivalent type recommended by the manufacturer.

  • Page 19: Cisco Iad2430-24fxs Iad

    Ultimate disposal of this product should be handled according to all national laws and regulations. Warning Statement 1040 Cisco IAD2430-24FXS IAD The Cisco IAD2430-24FXS IAD provides 24 analog foreign exchange station (FXS) ports with two 10/100BASE-T ports. The chassis RJ-21 analog voice interface •...

  • Page 20: Cisco Iad2431-16fxs

    One WIC/VIC slot • External flash memory AC and DC power inputs • Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Cisco IAD2431-8FXS Chassis IA D 24 31 -8 FX S (Figure 1-5) provides sixteen analog FXS ports with two...

  • Page 21: Cisco Iad2432-24fxs Iad

    IA D 24 31 -1 T1 E 1 (Figure 1-7) provides 24 analog FXS ports, two 10/100BASE-T ports, Cisco IAD2432-24FXS Chassis (Figure 1-8) provides eight analog FXS ports, two Fast Ethernet ports, Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Overview...

  • Page 22: Physical Description

    13 AC power input 1. This is not a redundant failover power supply connection. You must use either DC or AC. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Cisco IAD2435-8FXS Chassis IA D 2 4 3 5 -8...

  • Page 23: Leds

    LEDs The LEDs are located on the back panel of the Cisco IAD2430 series IADs. for the Cisco IAD2430 series IADs. The LEDs for the Cisco IAD2435 series IADs are located on the front of the chassis. OL-4234-06 Cisco IAD2435 Series IAD Back Panel Function Options...

  • Page 24

    ACT—green SYS—green PWR—green Figure 1-12 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Cisco IAD2400 Series LEDs (Cisco 2432-24FXS shown) Description Green indicates activity—when any of the 24 voice ports is active in a call (off hook) or when one of the analog ports is in use...

  • Page 25: Chassis Grounding

    Onboard flash memory contains the Cisco IOS software image, boot flash contains the ROMMON boot code, and counterfeit prevention contains the cookie configuration. The default flash memory for the Cisco IAD2430 series IADs is 128 MB. Onboard CPU memory is 256 MB.

  • Page 26: Specifications

    The operating system for the Cisco IAD2430 series IADs is the Cisco IOS software that resides in flash memory. Configuration Connections You can use an ASCII terminal or a PC to configure a Cisco IAD2430 series IAD. The configuration can be performed in several ways: Locally, with a direct connection through the serial port •...

  • Page 27: Manual Configuration

    The Cisco IAD2431 and Cisco IAD2432 IADs for a T1/E1 WAN interface are equipped with one • or two T1/E1 WAN ports. Cisco IAD2430 series IADs for an analog voice user interface are equipped with an RJ-21 port for • connection to a distribution panel.

  • Page 28

    1. HDLC = High-Level Data Link Control 2. TDM = time-division multiplexing 3. CSU/DSU = channel service unit/data service unit 4. CF = Flash memory Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 1-12 Interface To Services Supported ASCII terminal...

  • Page 29: Configuration Options

    Chapter 1 Overview of Cisco IAD2430 Series IADs Configuration Options The following interface options are available in Cisco IAD2430 series IADs: Table 1-2 Cisco IAD2430 Series IAD2430-24FXS IAD2431-8FXS IAD2431-16FXS IAD2431-1T1E1 IAD2432-24FXS IAD2435-8FXS 1. Analog voice interface. 2. T1/E1 ports. 3. 10/100BASE-T ports.

  • Page 30

    Cisco VIC2-4FXO interface card Figure 1-16 Cisco IAD model number: IAD2431-1T1E1 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 1-14 T1/E1 WAN Interface with Analog FXS User Interfaces Ethernet RJ-21 WAN Interface with Analog FXS and FXO User Interfaces...

  • Page 31: Chapter 2 Planning Your Installation

    Planning Your Installation Before you install your Cisco IAD2430 series integrated access device (IAD), see the information in this chapter: Location and Mounting Requirements, page 2-1 • Distance Limitations for Interface Cables, page 2-4 • Interference Considerations, page 2-6 •...

  • Page 32: Location And Mounting Requirements

    Power Source A Cisco IAD2430 series IADs with AC power supply autoselects either 100- to 127-V or 200- to 240-V operation. The Cisco IADs with AC power supply include a 6-foot (1.8-meter) electrical power cord. (A label near the power cord indicates the correct voltage, frequency, current draw, and power dissipation.)

  • Page 33: Cable Types

    Chapter 2 Planning Your Installation The Cisco IAD2430 series chassis provides inputs for both AC and DC power. Design your installation Caution to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you need to reboot it with only a single power source.

  • Page 34: Distance Limitations For Interface Cables

    EIA/TIA-232 signals. Table 2-2 Signal Rate 2400 4800 9600 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide T1/E1- WAN Port Distance Limitations Distance (Feet) Distance (Meters) 6200 1890 EIA/TIA-232 Speed and Distance Limitations...

  • Page 35

    Distance (Feet) Distance (Meters) 4100 1250 2050 1025 EIA/TIA-530/EIA/TIA-530A Speed and Distance Limitations Distance (Feet) Distance (Meters) 3940 1200 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Distance Limitations for Interface Cables Table 2-2 on page 2-4. If you...

  • Page 36: T1/e1-pbx Digital Voice Port Maximum Distances

    All module openings must be either occupied or covered to prevent electromagnetic interference. For advice on the prevention of electromagnetic interference, consult experts in radio frequency interference (RFI). Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Digital Voice Port Speed and Distance Limitations Distance (Feet) Distance (Meters)

  • Page 37

    Installing Cisco IAD2430 Series IADs This chapter contains the procedures for installing your Cisco IAD2430 series integrated access device (IAD) and consists of the following sections: Safety Recommendations, page 3-2 • Site Log, page 3-3 • Keeping Track—Checklist, page 3-3 •...

  • Page 38: C H A P T E R 3 Installing Cisco Iad2430 Series Iads

    • • Do not work alone if potentially hazardous conditions exist. • Never assume that power is disconnected from a circuit. Always check. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Chapter 3 Installing Cisco IAD2430 Series IADs OL-4234-06...

  • Page 39: Preventing Electrostatic Discharge Damage

    Comments, notes, and problems – Changes and updates to the Cisco IOS software – Keeping Track—Checklist We recommend that you use an installation checklist and maintain a Site Log. OL-4234-06 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Site Log...

  • Page 40: Installation Checklist

    Startup sequence steps completed Initial operation verified Mounting Tools and Equipment Obtain the following tools and parts needed for installing a Cisco IAD2430 series IAD: Standard flat-blade screwdriver as required for attaching brackets to rack or wall. • Phillips screwdriver for attaching brackets to the IAD.

  • Page 41: Unpacking And Inspection

    Note Unpacking and Inspection Do not unpack the Cisco IAD2430 series IAD until you are ready to install it. If the installation site is not ready, keep the chassis in its shipping container to prevent accidental damage. The IAD, cables, and any optional equipment you ordered might be shipped in more than one container.

  • Page 42: Rack-mounting The Chassis

    Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-9) (Brackets are not included with the Cisco IAD2435 IAD chassis (see Quick Installation Bracket for all Cisco IAD2430 Series Routers Except for Cisco IAD2435 IAD Quick Installation Bracket for Cisco IAD2435-8FXS Routers...

  • Page 43: Mounting Screws

    Rack-Mounting Screws Versus Wall-Mounting Screws Wall Mounting 19-Inch Rack Installation—Front Panel Forward 19-Inch Rack Installation—Back Panel Forward Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Rack-Mounting the Chassis Four 6–32 slotted hex screws (two per • bracket) and four plastic washers.

  • Page 44: Installing The Cisco Iad2430 Series Iads In A Rack

    Figure 3-7. Figure 3-7 Installing the Cisco IAD2430 Series IADs in a Rack The following warning applies only when the unit is rack-mounted: To prevent bodily injury when mounting or servicing this unit in a rack, you must take special Warning precautions to ensure that the system remains stable.

  • Page 45: Wall-mounting The Chassis

    Statement 248 Wall-Mounting the Cisco IAD2430, Cisco IAD2431, and Cisco IAD2432 IADs You can wall-mount the Cisco IAD2430, Cisco IAD2431, or Cisco IAD2432 IAD with either the right Caution side or the left side facing up;...

  • Page 46

    For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall Note anchors and washers must be size number 10. Figure 3-10 • Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-10 Attaching the Brackets for Wall-Mounting shows the orientation required for installation. Chapter 3...

  • Page 47: Wall-mounting The Cisco Iad2435 Iads

    3/4-inch (M3.5 x 20-mm) screws. You must provide the screws. Figure 3-11 OL-4234-06 Wall-Mounting the Chassis Bracket Keyhole for starter screw shows the screw holes. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Wall-Mounting the Chassis 3-11...

  • Page 48

    Hang the router on the screws as shown in Step 2 Step 3 Place the power supply on a horizontal surface. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-12 Screw Holes for Wall-Mounting the IAD2435 Screw holes Figure 3-12.

  • Page 49

    Mounting the IAD2435 Router on a Wall Distance between the two screws (7 5/8 in. [19.35 cm]) Mounting brackets Horizontal surface for placing the external 60-W power supply adapter Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Wall-Mounting the Chassis 3-13...

  • Page 50: Desktop-mounting The Chassis

    This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect the host to earth ground during normal use. Statement 242 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-14 Chapter 3...

  • Page 51

    Step 3 Figure 3-13.) OL-4234-06 ) wire and the ground lug provided in the ) or larger wire and an appropriate Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Installing the Ground Connection ) or larger wire and an 3-15...

  • Page 52

    Ground lug Figure 3-15 FX S Grounding lug Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-16 Crimping a Ground Lug onto the Ground Wire NEBS-Compliant Chassis Ground Connection Using Ground Lug Ground Lug Location on the Cisco IAD2435 IAD...

  • Page 53: Installing A Wan Or Voice Card

    Step 5 Installing a WAN or Voice Card The Cisco IAD2430 series IADs include a slot for a WAN interface card (WIC) or a voice interface card (VIC). The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards.

  • Page 54: Connecting Cables

    Off-premise wiring is designed to withstand power line crosses. On-premise wiring is protected from power line crosses by a device that provides overcurrent and overvoltage protection. Nevertheless, if the on-premise wiring is in close proximity Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-18 Chapter 3...

  • Page 55: Lan And Power Cables

    RJ-45-to-DB-9 console cable (included) communication (COM) port Modem for remote access RJ-45-to-DB-25 auxiliary cable (included) 100–240 VAC, 50–60 Hz Grounding power cord (included) Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Connecting Cables Results Passed Passed Passed Table 3-3...

  • Page 56

    Fast Ethernet port AUX port RJ-45-to-DB-9 console cable Figure 3-18 FX S Ethernet hub Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-20 LAN and Administrative Access Connections Console port Fast Ethernet (straight-through) RJ-45-to-DB-25 auxiliary cable LAN, Administrative Access, and Connections (Cisco IAD2435 IAD)

  • Page 57: Connecting The Input Power

    Connecting the Input Power To connect input power to the Cisco IAD, use the procedure in this section. The Cisco IAD2430 series chassis provides inputs for both AC and DC power. Design your installation Caution to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you must reboot it with only a single power source.

  • Page 58: Connecting The Console Port To A Pc Or An Ascii Terminal

    • 8 data bits 1 stop bit • no parity • Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-22 Connecting the External Power Supply to the Cisco IAD2435 IA D 24 35 -8 FX S WA N Fa stE the rne...

  • Page 59: Connecting The Auxiliary Port To A Modem

    Step 1 location 4 in Figure 3-17 on page Connect the second cable if it is required. Step 2 Not all models have two ports. Note OL-4234-06 3-20.) 3-20.) Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Connecting Cables 3-23...

  • Page 60: Wan And Voice Cables

    FXS/T3/E3 Statement 1044 The following warning also applies to Cisco IAD2430 units that have an RJ-21 interface. Note Before opening the unit, disconnect the telephone-network cables to avoid contact with Warning telephone-network voltages.

  • Page 61: Connecting The Rj-21 Cable In The Velcro Harness

    Figure 3-20 RJ-21 cable RJ-48 straight-through cable Connecting the RJ-21 Cable in the Velcro Harness For the Cisco IAD2430 series models that have a Velcro harness available for the RJ-21 cable (see Figure 3-21), follow these steps: Figure 3-21 Step 1...

  • Page 62

    Use a number 2 (flat or Phillips screwdriver) to attach the captive screws on the RJ-21 male connector Step 3 (see Figure 3-24). Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-26 Sliding the RJ-21 Cable Through the Velcro Harness F X S Pushing the RJ-21 Cable in to the Cisco IAD2435 IAD...

  • Page 63: Connecting A Serial Interface Port To A Csu/dsu Or A Synchronous Modem

    EIA-TIA-449 – V.35 OL-4234-06 Tightening the Captive Screws Tightening the Velcro Strap Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Connecting Cables F X S IA D 2 4 3 5 -8 F X S W A N F a st E th e rn...

  • Page 64: Cable

    (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-28...

  • Page 65: Cable

    PBX equipment, use the procedure in this section. Cable Use an RJ-21 cable with Amphenol 50-pin connectors (not included). OL-4234-06 T1/E1 Port to Network Connection Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Connecting Cables 3-29...

  • Page 66: Connecting The Digital Voice Port To A T1/e1-pbx

    Cable Use an RJ-48 T1/E1 cable (not included). Procedure Connect the RJ-48 T1/E1 cable to the T1/E1 port. See Step 1 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-30 Analog Voice Connection RJ-21 cable Chapter 3 Installing Cisco IAD2430 Series IADs...

  • Page 67: Ports, Connectors, And Pinouts

    V.35 X.21 RJ-48/Straight-through T1/E1 trunk RJ-48/Straight-through Digital PBX, T1/E1 RJ-21X/50-conductor Distribution panel for analog telephone, fax, PBX, or central office line Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Ports, Connectors, and Pinouts Digital PBX or channel bank 3-31...

  • Page 68: Connecting To A Modem

    Step 3 Key in the telephone number of the Cisco IAD external modem, or, if you are using a Hayes-compatible modem, enter ATDT and the number to be dialed. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-32 Chapter 3...

  • Page 69: Connecting Backup Power

    UPS functionality is not available on the IAD2435 IAD. Note The Cisco IAD2430 series IAD chassis provides inputs for both AC and DC power. Design your Caution installation to use only one type of power. Do not use AC and DC power at the same time. If you do, the unit stops operating, and you must reboot it with only a single power source.

  • Page 70: Connecting An Uninteruptible Power Supply Ups To An Ac-powered Cisco Iad2430 Series Iad

    Connecting a Backup Battery to a DC-Powered Cisco IAD AC wall plug Use a backup battery only if you are not using AC to power your Cisco IAD2430 series IAD. Do not use Caution AC and DC power at the same time. If you do, the unit stops operating, and you must reboot it with only...

  • Page 71

    UPS documentation before you set up your Note system. Figure 3-32 Connecting a UPS to an AC-Powered Cisco IAD AC wall plug OL-4234-06 Cisco IAD 2430 series Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Connecting Backup Power IAD 243 1-8 AC plug 3-35...

  • Page 72

    Chapter 3 Installing Cisco IAD2430 Series IADs Connecting Backup Power Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 3-36 OL-4234-06...

  • Page 73: Chapter 4 Powering On Cisco Iad2430 Series Iads

    Powering On Cisco IAD2430 Series IADs To power on your Cisco IAD2430 series integrated access device (IAD), perform the following tasks in the order listed, as required: Checklist for Power-On, page 4-1 • Power-On Procedure, page 4-1 • Initial Configuration Procedures, page 4-2 •...

  • Page 74: Initial Configuration Procedures

    Configuration Fundamentals Configuration Guide Initial Configuration Procedures This section describes how to prepare the Cisco IAD2430 IAD series IAD to perform basic communication functions. You may initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network.

  • Page 75: Cisco Ios Cli

    (Router#) to save the configuration to NVRAM. Verify the initial configuration. See the OL-4234-06 privilege 15 secret 0 <mypassword> “Verifying and Saving Your Configuration” section on page Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Initial Configuration Procedures 4-8.

  • Page 76: Setup Command Facility

    Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration. The enable secret is a password used to protect access to Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Chapter 4 Powering On Cisco IAD2430 Series IADs...

  • Page 77

    [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. OL-4234-06 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Initial Configuration Procedures...

  • Page 78: Manual Configuration

    IP address for the port. After setting the address, you can configure the Cisco IAD remotely through a Telnet connection. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide “Verifying and Saving Your Configuration” section on page 4-8 for the configuration instructions.

  • Page 79: Configuring A T1/e1 Port For A Wan Connection

    If necessary, changes the DS1 link framing format. The default is SuperFrame (sf). If necessary, changes the line encoding format for the DS1 link. The default is ami. Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Initial Configuration Procedures...

  • Page 80: Configuring Digital Voice

    • signaling (CAS) voice groups, or time-division multiplexing (TDM) cross-connects, see the Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide. Verifying and Saving Your Configuration To verify the configuration and save it in NVRAM so that the configuration remains in effect if the...

  • Page 81: Troubleshooting

    If you reboot the Cisco IAD or turn off the Note power before you complete this step, you lose the configuration. Cisco IAD2430 Series Software Configuration Guide Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide Troubleshooting at the...

  • Page 82

    Console screen display freezes 1. See the “Obtaining Documentation and Submitting a Service Request” section on page Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 4-10 Troubleshooting the Cisco IAD Possible Cause Faulty power cable...

  • Page 83: I N D E X

    EIA/TIA-232 EIA/TIA-530 electrical safety guidelines electromagnetic interference See EMI electrostatic discharge See ESD 2-4, 2-6 Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide iii-xvi 3-28 1-10, 1-11 3-23, 3-27, 3-28, 3-30 3-22 3-16 3-5, 3-29 3-28 3-31...

  • Page 84

    Telco 19-Inch Rack Installation—Rear Panel Forward Wall-Mounting the Chassis 3-11 ground loops, EMI effects of installation checklist Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide IN-2 rack-mounting tools, parts, and equipment required installation checklist interface options See Cisco IOS software...

  • Page 85

    SELV-to-TNV connection hazard WAN port hazardous voltages 1-13 working during lightning activity warnings, safety X.21 distance limitations Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide 4-10 1-10 3-22, 3-32 4-10 3-33, 3-34 3-9, 3-11 3-28...

  • Page 86

    Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide IN-4 OL-4234-06...

Comments to this Manuals

Symbols: 0
Latest comments: