Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Hardware
  5. IDS 4210 - Intrusion Detection Sys 4210...
  6. Installation manual
Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor Installation Manual

Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor Installation Manual

User guide
Hide thumbs Also See for IDS 4210 - Intrusion Detection Sys 4210 Sensor:
Table of Contents

Advertisement

Quick Links

Download this manual
Installing IDS-4210
This chapter describes IDS-4210 and how to install it and its accessories.
Note
IDS-4215 replaced IDS-4210, which is no longer sold.
Note
If you purchased an IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install
Cisco IPS 5.x. for more information, see
IDS-4210 does not support inline (IPS) mode.
Note
The BIOS on IDS-4210 is specific to IDS-4210 and must only be upgraded under instructions from Cisco
Caution
with BIOS files obtained from the Cisco website. Installing a non-Cisco or third-party BIOS on
IDS-4210 voids the warranty. For more information on how to obtain instructions and BIOS files from
the Cisco website, see Obtaining
This chapter contains the following sections:
•
Front and Back Panel Features and Indicators, page 2-2
•
Upgrading the Memory, page 2-3
•
Installing IDS-4210, page 2-5
Installing the Accessories, page 2-7
•
OL-8677-01
C H A P T E R
Upgrading the Memory, page
Obtaining Cisco IPS Software, page
Installing Cisco Intrusion Prevention System Appliances and Modules 5.1
2
2-3.
11-1.
2-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IDS 4210 - Intrusion Detection Sys 4210 Sensor and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor

Summary of Contents for Cisco IDS 4210 - Intrusion Detection Sys 4210 Sensor

  • Page 1 IDS-4210 does not support inline (IPS) mode. Note The BIOS on IDS-4210 is specific to IDS-4210 and must only be upgraded under instructions from Cisco Caution with BIOS files obtained from the Cisco website. Installing a non-Cisco or third-party BIOS on IDS-4210 voids the warranty.

  • Page 2: Front And Back Panel Features And Indicators

    Ethernet port; blinks when activity occurs on this channel. LAN2 activity/link Amber Lights up when the LAN2 connector is linked to an Ethernet port; blinks when activity occurs on this channel. Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01...

  • Page 3: Upgrading The Memory

    (unused) Upgrading the Memory IDS-4210, IDS-4210-K9, and IDS-4210-NFR must have 512 MB of RAM to support Cisco IPS 5.1. If you are upgrading an existing IDS-4210, IDS-4210-K9, or IDS-4210-NFR to 5.1, you must insert one additional 256-MB DIMM (part number IDS-4210-MEM-U) to upgrade the memory to the required 512 MB minimum.
  • Page 4 Power on the sensor and make sure the new memory total is correct. Step 11 If the memory total does not reflect the added DIMMs, repeat Steps 1 through 4 to ensure the Note DIMMs are seated correctly in the socket. Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01...

  • Page 5: Installing Ids-4210

    Warning Statement 1030 Follow proper safety procedures when performing these steps by reading the safety warnings in Caution Regulatory Compliance and Safety Information for the Cisco Intrusion Prevention System 4200 Series Appliance Sensor. Note If you purchased an IDS-4210 before July 2003, you must upgrade the memory to 512 MB to install Cisco IPS 5.x.
  • Page 6 Upgrade IDS-4210 to the latest Cisco IPS software. Step 8 For the procedure, see Obtaining Cisco IPS Software, page 11-1. You are now ready to configure intrusion detection on the appliance. Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01...

  • Page 7: Installing The Accessories

    – Installing and Using Cisco Intrusion Prevention System Device Manager 5.1 Configuring the Cisco Intrusion Prevention System Sensor Using the Command Line Interface – Installing the Accessories You can install a bezel, and center or front mounting brackets for the IDS-4210.

  • Page 8: Installing Center Mount Brackets

    To install the center mount brackets in a two-post, open-frame relay rack, follow these steps: Determine where you want to place IDS-4210. Step 1 Mark the upper and lower mounting positions on the two posts. Step 2 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01...
  • Page 9 Secure the bracket to IDS-4210 chassis using two screws (see Figure 2-3 on page 2-9). Step 4 Repeat Step 4 to install the remaining bracket on the other side of IDS-4210. Step 5 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 OL-8677-01...
  • Page 10 100M bps LINK 100M DRIV E 0 DRIV E 1 CON S ETH ERN ET 0 ETH ERN ET 1 SCS I LVD ONLY DRIV E 0 DRIV E 1 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 2-10 OL-8677-01...
  • Page 11 Use the bolts provided with the rack to fasten the front flanges of IDS-4210 to the rack. Step 5 Note When you are done, IDS-4210 should not slide on the channel bar. Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 2-11 OL-8677-01...
  • Page 12 Chapter 2 Installing IDS-4210 Installing the Accessories Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 2-12 OL-8677-01...

Table of Contents