Terminal Block Settings; Inputs - Negative Or Positive Common; Terminal Block 9 - E1 - N; Terminal Block 10 - E2 - N - Abexo 051D User Manual

Each terminal block is linked to a parameter: they can all be identified with letter E.
E0 INPUTS, NEGATIVE-POSITIVE COMMON
E1 TERMINAL BLOCK 9 - E1
E2 TERMINAL BLOCK 10 - E2
E3 TERMINAL BLOCK 11 - E3
E4 TERMINAL BLOCK 12 - E4
E0
E' possibile riferire gli ingressi della morsettiera sia al POSITIVO che al NEGATIVO.
Per selezionare il comune degli ingressi al NEGATIVO ( morsetti 14, 15, 16 etichettati con -) impostare
Per selezionare il comune degli ingressi al POSTIVO (morsetti 17, 18 etichettati con +) impostare
E1
Terminal block 9 is associated with a normally open (N.O.) contact. The parameters that can be set are:
N GO
DISABLED, START,
E2
Terminal block 10 is associated with a normally open (N.O.) contact. The parameters that can be set are:
N GO
DISABLED, START,
E3
Terminal block 11 is associated with a normally closed (N.C.) contact. The parameters that can be set are:
N DISABLED, St STOP. This control unit is supplied with the standard setting where terminal block 11 is disabled
When a NORMALLY CLOSED contact is connected to terminal block 11, it is automatically detected by the control unit that sets
the parameter of the terminal block to the correct safety fuction, in this case
E4
Terminal block 12 is associated with a normally closed (N.C.) contact. The parameters that can be set are:
N DISABLED, tc CLOSING PHOTOCELL - MODE 1, and
the standard setting where terminal block 12 is disabled
block 12, it is automatically detected by the control unit that sets the parameter of the terminal block to the correct safety fuction,
E4 tc CLOSING PHOTOCELL - MODE 1. This feature is called AUTO-ENABLE.
in this case =
E5
Terminal block 13 is associated with a normally closed (N.C.) contact. The parameters that can be set are:
N DISABLED, ta OPENING PHOTOCELL,
setting where terminal block 13 is disabled
is automatically detected by the control unit that sets the parameter of the terminal block to the correct safety fuction, in this case
E5 = tA OPENING PHOTOCELL. This feature is called AUTO-ENABLE.
E6
Terminal block 14 is associated with a normally closed (N.C.) contact. The parameters that can be set are:
n DISABLED, Ao LIMIT SWITCH OPENING MOTOR A. This control unit is supplied with the standard setting where terminal block
14 is disabled = n). When a NORMALLY CLOSED contact is connected to terminal block 14, it is automatically detected by
(E6
the control unit that sets the parameter of the terminal block to the correct safety fuction, in this case
OPENING MOTOR A. This feature is called AUTO-ENABLE.

TERMINAL BLOCK SETTINGS

2
Go
PE
N
AUTO-ENABLE
N
AUTO-ENABLE
INPUTS, NEGATIVE-POSITIVE COMMON
TERMINAL BLOCK 9 - E1 - NORMALLY OPEN
PE PO
PEDESTRIAN, OPEN DEAD MAN,
TERMINAL BLOCK 10 - E2 - NORMALLY OPEN
PE PO
PEDESTRIAN, OPEN DEAD MAN,
TERMINAL BLOCK 11 - E3 - NORMALLY CLOSED
TERMINAL BLOCK 12 - E4 - NORMALLY CLOSED
TERMINAL BLOCK 13 - E5 - NORMALLY CLOSED
tc CLOSING PHOTOCELL - MODE 1. This control unit is supplied with the standard
= n). When a NORMALLY CLOSED contact is connected to terminal block 13, it
(E5
TERMINAL BLOCK 14 - E6 - NORMALLY CLOSED
USER MANUAL - 230 VAC MULTIFUNCTION CONTROL UNIT - 051D
E5 TERMINAL BLOCK 22 - E5
NEGATIVE
E6 TERMINAL BLOCK 23 - E6
START
E7 TERMINAL BLOCK 24 - E7
PEDESTRIAN
E8 TERMINAL BLOCK 25 - E8
E9 TERMINAL BLOCK 26 - E9
PC
CLOSE DEAD MAN,
PC
CLOSE DEAD MAN,
E3
td CLOSING PHOTOCELL - MODE 2. This control unit is supplied with
= n). When a NORMALLY CLOSED contact is connected to terminal
(E4
8
E0 = 2.
E0 = 1.
EL
ELECTRIC LOCK.
EL
ELECTRIC LOCK.
= St STOP. This feature is called AUTO-ENABLE.
E6
N
AUTO-ENABLE
N
AUTO-ENABLE
N
AUTO-ENABLE
N
AUTO-ENABLE
N
AUTO-ENABLE
(E3 = n).
Ao
= LIMIT SWITCH