Table of Contents
Advertisement
In this section it is possible to set the motor working time or the obstacle detector threshold. These procedures can be identified
by letter P: it is always possible to manually change the values at the end of the programming.
BEFORE STARTING:
- Check the gate: it must be fully closed
- Check that the motor rotation is correctly performed: both motors must open during the opening movement; both motors must
close during the closing movement.
- Be sure to have a START device: for example a transmitted stored as (symbol) or a key-switch connected to terminal block 9 with
value
E1
=
Go
(START).
- In order to program the control unit without the slowdown working time, set:
During the configuration phase, on the display you will se the parameter you are setting, for example, if the display shows
means that the control unit is setting parameter
STORE A TRANSMITTER AS START DEVICE
r1
1. Select parameter
using key (←) or (→).
2. After a few seconds (
=_
3. Keep the button of the transmitter you want to store pressed: the display shows (
4. Press KEY (+): the display shows (
=2
(display
means position 2 in the memory, display
4a. If the display shows (
4b. If the display does not show (
the receiver), or the radio receiver is faulty.
P1 / P2
P1: configuration 1 motor mode L5=Y, standard working time A1, motor A slowdown time
proceed with configuration
P2: motor A and motor B standard time A1/b1, slowdown time
the slowdown time of one of the motors or both, ignore
_ _
After 2 seconds two dashes will appear on the display. Perform a START command to start
You are working on motor A STANDARD TIME. Motor A starts the opening movement. When the leaf controlled
by motor A has completed 90% of the opening movement, send another START command. The control unit will
A1
automatically move to
You are working on motor A SLOWDOWN TIME. Motor A slows down. It is advisable to wait 2-3 seconds when
the leaf has come to a completely open position and the motor ended the opening movement, then issue a new
A2
START command. The control unit will automatically move to
You are working on motor B STANDARD TIME. Motor A stops and motor B slows down. When the leaf controlled
by motor B has completed 90% of the opening movement, send a START command. The control unit will auto-
B1
matically move to
You are working on motor B SLOWDOWN TIME. Motor B slows down. It is advisable to wait 2-3 seconds when
the leaf has come to a completely open position and the motor ended the opening movement, then issue a new
B2
START command. The control unit will automatically move to
You are working on AUTO-CLOSE TIME F0. Both motors are idle. The display will show F0, then the seconds
F0
counting. Count the desired time you want your automation to wait before starting the auto-closure operation,
then press the START command
> Guided configurations count the same time for opening and closing movements.
> If a leaf perform the SLOWDOWN operation only during opening movement (and not during the closing movement)
follow this procedure:
- Select
A1
using keys (←) or (→)
A1
- Decrease
value by 1 second using key (-)
A2
- Select
using keys (←) or (→)
A2
- Increase
value by 3 seconds using key (+)
- Perform a complete cycle
If the slowdown movement is performed, your configuration has come to an end. If not, repeat this procedure. Use the same pro-
cedure for motor B, if needed.
GUIDED CONFIGURATION
A1
) will appear on the display
=1
). Your transmitter has been successfully stored in position 1 in the control unit's memory
=.
) your transmitter has not been stored.
=.
), the control unit did not receiver your transmitter (E.G.: different frequency compared to
GUIDED CONFIGURATION: 1/2 MOTOR/S
P1
read lines A1,
A2
and F0. If you disabled the slowdown time of the motor, skip
A2
configuration step
b2
configuration step
A2
(STANDARD TIME - MOTOR A).
=3
means position 3, etc up to 99).
A2/b2
and auto-close time
A1
and/or b1.
b1
configuration step
F0
configuration step
11
USER MANUAL - 230 VAC MULTIFUNCTION CONTROL UNIT - 051D
B2
0. 0
or
=
and then proceed with programming.
=._
)
A2
and auto-close time F0. To
F0
configuration. If you disabled
A1
A1
it
A1
and/or b1.
configuration.
Advertisement
Table of Contents
