Table of Contents
Advertisement
f7
FAST CLOSURE
The FAST CLOSURE function allows the gate to be closed after passing in front of both photocells (open and close or close and open).
Closing begins 5 seconds after passing in front of the photocells. This function is only enabled once per WORKING CYCLE and if the gate
movement is not interrupted.
F7
If
= all START orders initiate this function: the remote controls stored with the functions
CLOSURE, the terminal board inputs associated with the START
remote controls stored with the radio function
F8
PHOTOCELLS LOGIC: SLIDING
F8
n
If
=
the photocells operate with the logic of SWING GATE automation:
- OPENING PHOTOCELLS (terminal 13 parameter
movement status from CLOSING to OPENING SUSPENDED. During OPENING they have no effect on the ongoing operation.
- CLOSING PHOTOCELLS (terminal 12 parameter
F8
y
the photocells operate with the logic of SLIDING automation:
If
=
- OPENING PHOTOCELLS (terminal 13 parameter
seconds, CLOSING is interrupted. A subsequent START order starts the gate in CLOSING mode.
They have no effect during the CLOSING operation.
- CLOSING PHOTOCELLS (terminal 12 parameter
no effect during the OPENING operation.
L0
This parameter allows changes to be made to the operating logic of terminals 20 + e 21 - (
is useful for controlling a 12VDC electric lock or a 3 W 12 VDC LED flashing light. The output of the electric lock can also be controlled by
remote control.
L0
00
→
=
The output is disabled. Only remote controls associated with the function
activate the control unit's output 20 + e 21 - (
an gate adjacent to the automatic gate.
L0
01
→
=
The output is enabled to manage an electric lock installed on the door moved by motor A. At the beginning of each
OPENING movement, the control unit releases the electric lock. Remote controls stored as
L0
02
→
=
The output is enabled with an intermittent flashing function. During OPENING, the flashing light will perform fast flashes.
During CLOSING the flashes will be slow. During the automatic closing time, the flashing light is
permanently lit.
L0
03
→
=
The output is enabled with the steady light function during the operation. During OPENING, CLOSING and the AUTOMATIC
CLOSING TIME the flashing light is on.
L1
OIL RECYCLING / MOTOR HEATING
With this function it is possible to heat the motors and the control unit box cyclically. In the case of systems with hydraulic motors, it is
useful to circulate the oil periodically: each cycle lasts 10 minutes and
cycle. This function is activated after 10 minutes with the gate fully closed or open: any operation on the control unit or interruption of a
photocell resets the time count to zero. The motors are active in the final part of each cycle. For example, by setting
remain switched off for 7 minutes and then switched on for the remaining
the last operation performed).
L3
ONLY MOTOR A MODE
L3
By enabling this function
ified. This function is useful when installing a 1 door swing gate or sliding gates. If this control unit is used on a sliding gate, set parameter
F8
y
=
to select the correct photocell logic.
GENERAL FUNCTIONS
r4
activate the FAST CLOSURE.
E5
=
E4
tc
=
E5
=
E4
=
KICK BACK
L0
). The activation of the electric lock by remote control can be useful to manage a pedestri-
y
=
only motor A will be managed. The parameters relating to motor B (
USER MANUAL - 230 VAC MULTIFUNCTION CONTROL UNIT - 051D
MINIMUM:
go
oP
, OPEN
or PEDESTRIAN functions
MINIMUM:
tA
): suspend the OPENING as long as the beam is interrupted. Reverses the
E4
td
): reverse the movement from CLOSING to OPENING.
,
=
tA
): during OPENING they reverse the movement for 3 seconds. After these 3
tc
E4
td
): reverse the movement from CLOSING to OPENING. They have
,
=
MINIMUM:
MINIMUM:
0
L1
represents the minutes that the motor/box is heated in each
3
minutes after the function is active (i.e. after 17 minutes from
MINIMUM:
20
n
MAXIMUM:
r1
r3
START,
PEDESTRIAN,
pe
F7
. If
n
MAXIMUM:
0
MAXIMUM:
L0
) associated with the electric lock. This output
EL
(activate the electric lock for 3 seconds) can
EL
unlock the electric lock.
min
MAXIMUM:
0
MAXIMUM:
b1
b8
–
) can no longer be mod-
y
r4
FAST
n
=
(disabled) only
y
3
8
min
L1
03
=
the motors
y
Advertisement
Table of Contents
