Motor B Settings; Standard Time; Slowdown Time; Soft Start (Achieving Set Torque) - Abexo 051D User Manual

Motor B can be configured using 8 parameters identified by the letter b.
Forces and thresholds are expressed in decimals and correspond to %. Ex:

STANDARD TIME

b1

SLOWDOWN TIME

b2

SOFT START (ACHIEVING SET TORQUE)

b3
WAITING TIME BEFORE CLOSING
b4
b1 STANDARD TIME
Motor B works for B1 seconds at force B5. At the end of this time, motor B slows down. This occurs during both opening and closing.
Motor B closes before motor A. Motor B opens
b2 SLOWDOWN TIME
b2
Motor B slows down for
closing. To disable the slowdown of motor B, set the parameter
b3 SOFT START (ACHIEVING SET TORQUE)
When starting, motor B gradually increases the force until it reaches the set force
disabled.
b4 DELAY AT CLOSING (MOTOR B)
b4
Motor B opens seconds after motor A. This time is useful to avoid overlapping of the doors during the opening phase.
b5

TORQUE ADJUSTMENT/STANDARD FORCE

b1
During STANDARD TIME
10%. The force of the motor increases or decreases the sensitivity of the obstacle sensor. The greater the force set, the lower the sensitivity.
The lower the force, the greater the sensitivity.
TORQUE ADJUSTMENT/STANDARD FORCE
b6
During SLOWDOWN TIME
steps of 10%. The force of the motor increases or decreases the sensitivity of the obstacle sensor: the greater the force set, the lower the
sensitivity; the lower the force set, the higher the sensitivity.
b7 STANDARD OBSTACLE
If the force of motor B detected is greater than the STANDARD OBSTACLE THRESHOLD
unit detects an obstacle. If the force of motor B detected is greater than the set threshold, the gate reverses the movement if it is the first
detection in the working cycle, otherwise it goes to the limit switch. Once the obstacle is detected, the gate performs a safety procedure
by moving one door at a time.
In order to facilitate calibration of the STANDARD OBSTACLE THRESHOLD, the control unit's display during CLOSING shows the force of
00
motor B as a number from
SLOWDOWN OBSTACLE THRESHOLD
b8
During the SLOWDOWN TIME
b8
CLE THRESHOLD set. Obstacle detection during slowdown acts as a limit switch.
In order to facilitate calibration of the SLOWDOWN OBSTACLE THRESHOLD, the control unit's display during CLOSING shows the force of
00
motor B as a number from

MOTOR B SETTINGS

sec = seconds
Times are expressed in seconds
14 sec
7 sec
0,8 sec
6 sec
B4 seconds after motor A.
b6
seconds at force . The slowdown phase is performed after the normal working time for both opening and
b5
the force of motor B is
b2
the force of the motor is
99
. To disable obstacle detection press the (+) KEY until the display shows
to
b2
the control unit detects an obstacle if the force of the motor is greater than the SLOWDOWN OBSTA-
99
to . To disable obstacle detection during slowdown press the (+) KEY until the display does not show
% = percentage parameter
STANDARD FORCE (from 10% to 100%)
b5
SLOWDOWN FORCE (from 10% to 100%)
b6
STANDARD OBSTACLE DETECTION THRESHOLD
b7
SLOWDOWN OBSTACLE DETECTION THRESHOLD
b7
MINIMUM:
MINIMUM:
b2 0. 0
= sec.
MINIMUM:
MINIMUM:
MINIMUM: 01
% of the total. The force of motor B can be set from 10% to 100% in steps of
01
MINIMUM:
b6
% of the total. The SLOWDOWN FORCE can be set from 10% to 100% in
MINIMUM: 00
00
MINIMUM:
17
USER MANUAL - 230 VAC MULTIFUNCTION CONTROL UNIT - 051D
n = disabled
01
= 10%
0. 0 sec MAXIMUM:
0. 0 sec MAXIMUM:
0. 1 sec MAXIMUM:
b5
. During this time the obstacle detection sensor is
0. 0 sec MAXIMUM:
= 10% MAXIMUM:
= 10% MAXIMUM:
= 0% MAXIMUM:
b7
set during STANDARD TIME
= 0% MAXIMUM:
8/10 %
10/10 %
n %
n %
99 sec
99 sec
1. 5 sec
a1+a2 sec
10 = 100%
10
= 100%
n = disabled
b1
the control
n
.
n
= disabled
n
.