HP 2133 Mini-Note Maintenance And Service Manual

Hp 2133 mini-note: supplementary guide.
Hide thumbs
HP 2133 Mini-Note PC and HP 2140 Mini-Note
PC
Maintenance and Service Guide

Advertising

   Related Manuals for HP 2133 Mini-Note

   Summary of Contents for HP 2133 Mini-Note

  • Page 1

    HP 2133 Mini-Note PC and HP 2140 Mini-Note Maintenance and Service Guide...

  • Page 2

    Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3

    Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.

  • Page 4

    Safety warning notice...

  • Page 5: Table Of Contents

    Table of contents 1 Product description 2 External component identification Model 2133 ... 5 Top components ... 5 Front components ... 8 Right-side components ... 9 Left-side components ... 10 Bottom components ... 11 Wireless antennas (select models only) ... 12 Model 2140 ...

  • Page 6: Table Of Contents

    4 Removal and replacement procedures Preliminary replacement requirements ... 36 Tools required ... 36 Service considerations ... 36 Grounding guidelines ... 38 Unknown user password ... 41 Component replacement procedures ... 42 Serial number ... 42 Computer feet ... 43 Battery ...

  • Page 7: Table Of Contents

    10.1-inch, SD display specifications ... 80 10.1-inch, HD display specifications ... 81 8.9-inch, WXGA display specifications ... 81 8.9-inch, WSVGA display specifications ... 83 Hard drive specifications ... 84 System DMA specifications ... 85 System interrupt specifications ... 86 System I/O address specifications ... 87 System memory map specifications ...

  • Page 8

    Requirements for specific countries and regions ... 111 11 Recycling Battery ... 112 Display ... 112 Index ... 118 viii...

  • Page 9: Product Description

    Product Name Processors Chipset Graphics Panels Memory Description HP 2133 Mini-Note PC HP 2140 Mini-Note PC VIA Technology C7-M Ultra Low Voltage (ULV) processors ● VIA C7-M ULV 1.6-GHz processor, 800-MHz front-side bus (FSB), 8-W thermal design power (TDP) ●...

  • Page 10

    Category Mass storage device Optical drive Diskette drive Audio Webcam Modem Ethernet Wireless External media card Chapter 1 Product description Description ● 2048-MB total system memory (2048 × 1) ● 1024-MB total system memory (1024 × 1) ● 512-MB total system memory (512 × 1) Supports 9.5-mm (2.5-inch) serial ATA (SATA) hard drives Supports the following SATA hard drives: ●...

  • Page 11

    2-pin DC connector) 6-cell, 55-Wh Li-ion battery 3-cell, 28-Wh Li-ion battery Security Supports Kensington security lock HP 3D DriveGuard Operating system Preinstalled: Windows Vista® Basic 32 with Office 2007 Ready Windows Vista Business 32 with Office 2007 Ready Windows®...

  • Page 12

    Category Chapter 1 Product description Description Hard drive Memory module Model 2133 Model 2140 √ √ √ √...

  • Page 13: Model 2133, Top Components, Display

    External component identification Model 2133 Top components Display Item Component Speakers (2) Wireless antennas (2) Function Produce sound. Send and receive signals from one or more wireless devices. NOTE: The antennas are not visible from the outside of the computer. Model 2133...

  • Page 14: Keys

    Item Component Internal microphones (2) Webcam (select models only) Keys Item Component Windows logo key Windows applications key Embedded numeric keypad keys Function keys Chapter 2 External component identification Function Record sound. NOTE: If there is a microphone icon next to each microphone opening, your computer has internal microphones.

  • Page 15: Touchpad

    TouchPad Item Component TouchPad on/off button Left TouchPad button* TouchPad* TouchPad scroll zone Right TouchPad button* *This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Hardware and Sound > Mouse. Function Enables/disables the TouchPad.

  • Page 16: Front Components

    Options. Blinking: The hard drive is being accessed. ● Blue: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Broadband Wireless Module, and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off.

  • Page 17: Right-side Components

    Right-side components Item Component ExpressCard slot SD Card Reader USB port RJ-45 (network) jack Battery light Power connector Security cable slot Function Supports optional ExpressCards 54. Supports the following optional digital card formats: ● Secure Digital (SD) Memory Card ● MultiMediaCard (MMC) Connects an optional USB device.

  • Page 18: Left-side Components

    Left-side components Item Component External monitor port Vent Powered USB port Audio-in (microphone) jack Audio-out (headphone) jack Chapter 2 External component identification Function Connects an external VGA monitor or projector. Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.

  • Page 19: Bottom Components

    Bottom components Item Component Battery release latches (2) Battery bay Service tag Vents (3) Function Release the battery from the battery bay. Holds the battery. Provides the product brand and series name, serial number (s/n), and product number (p/n) of your computer. Have this information available when you contact technical support.

  • Page 20: Wireless Antennas (select Models Only)

    Wireless antennas (select models only) On select computer models, at least 2 antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer. NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions.

  • Page 21: Model 2140, Top Components, Display

    Model 2140 Top components Display Component Speakers (2) Internal microphones (2) Webcam Description Produce sound. Record sound. NOTE: If there is a microphone icon next to each microphone opening, your computer has internal microphones. Records audio and video, and captures still photographs. Model 2140...

  • Page 22

    Keys Component Function keys Embedded numeric keypad keys Chapter 2 External component identification Description Displays system information when pressed in combination with key. Executes frequently used system functions when pressed in combination with a function key or the Execute frequently used system functions when pressed in combination with the key.

  • Page 23

    TouchPad Component TouchPad light TouchPad on/off button Left TouchPad button TouchPad TouchPad scroll zone Right TouchPad button Description ● White: TouchPad is enabled. ● Amber: TouchPad is disabled. Enables/disables the TouchPad. Functions like the left button on an external mouse. Moves the pointer and selects or activates items on the screen.

  • Page 24

    Front components Component Power light Power switch Drive light Wireless light Wireless switch Chapter 2 External component identification Description ● Blue: The computer is on. ● Blinking: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ●...

  • Page 25

    Right-side components Component ExpressCard slot SD Card Reader USB port RJ-45 (network) jack Battery light Power connector Security cable slot Description Supports optional ExpressCards 54. Supports the following optional digital card formats: ● MultiMediaCard (MMC) ● Secure Digital (SD) Memory Card Connects an optional USB device.

  • Page 26

    Left-side components Component External monitor port Vent Powered USB port Audio-in (microphone) jack Audio-out (headphone) jack Chapter 2 External component identification Description Connects an external VGA monitor or projector. Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.

  • Page 27

    Bottom components Component Battery bay Battery release latches (2) Service tag Vents (4) Description Holds the battery. Release the battery from the battery bay. Provides the product brand and series name, serial number (s/n), and product number (p/n) of your computer. Have this information available when you contact technical support.

  • Page 28: Wireless Antennas

    Wireless antennas On select computer models, at least 2 antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer. NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions.

  • Page 29: Illustrated Parts Catalog Serial Number Location

    Illustrated parts catalog Serial number location When ordering parts or requesting information, provide the computer serial number and model number located on the bottom of the computer. Serial number location...

  • Page 30: Computer Major Components

    Computer major components Item Description 8.9-inch, WXGA display assemblies for use with model 2133 (include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables) For use only with computer models equipped with a camera module For use only with computer models not equipped with a camera module Chapter 3 Illustrated parts catalog Spare part number 483384-001...

  • Page 31

    Item Description 10.1-inch WXGA display assemblies for use with model 2140 (include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables) For use in SD computer models with camera module For use in HD computer models with camera module 8.9-inch, WSVGA display assemblies (include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables) For use only with computer models equipped with camera module and system boards with the...

  • Page 32

    Item Description For use in Thailand For use in Turkey For use in the United Kingdom For use in the United States Memory modules (PC2-5300, 667-MHz, DDR2) For use only in model 2133: ● 2048-MB ● 1024-MB ● 512-MB For use only in model 2140: ●...

  • Page 33

    Item Description Bracket Kit for use only in model 2133 (see spare part number information) NOTE: Model 2140 uses only the bracket shown by 8b. (8a) Audio/USB connector bracket (8b) ExpressCard assembly bracket (8c) USB/RJ-45 connector bracket Plastics/Cable Kit for use only in model 2133 (see Plastics/Cable Kit spare part number information) Plastics/Cable Kit for use only in model 2140 (see Plastics/Cable Kit spare part number information)

  • Page 34

    Item Description ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,...

  • Page 35

    Item Description Broadcom 4322 802.11a/b/g/n WLAN module For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,...

  • Page 36: Bracket Kit

    Bracket Kit Item Description Bracket Kit for use only in model 2133: ExpressCard assembly bracket USB/RJ-45 connector bracket Audio/USB connector bracket Chapter 3 Illustrated parts catalog Spare part number 482266-001...

  • Page 37: Plastics/cable Kit, Miscellaneous Parts

    Bluetooth module cable ExpressCard bracket (model 2140 only; not illustrated) Hinge bracket (model 2140 only; not ilustrated) Miscellaneous parts Description 65-W HP Smart AC adapter Power cords: For use in Australia For use in Brazil For use in Denmark For use in Europe, the Middle East, and Africa...

  • Page 38: Sequential Part Number Listing

    Description For use the United States Screw Kit for use in model 2133 ● Phillips PM2.0×3.0 screw ● Torx8 T8M2.5×10.0 screw ● Torx8 T8M2.5×5.0 screw ● Torx8 T8M2.0×6.0 screw ● Torx8 T8M2.0×4.0 screw Screw kit for use only in model 2140 ●...

  • Page 39

    Spare part Description number 414045-001 512-MB memory module for use in model 2133 (PC2-5300, 667-MHz, DDR2) 414046-001 1024-MB memory module for use in model 2133 (PC2-5300, 667-MHz, DDR2) 417506-001 2048-MB memory module for use in model 2133 (PC2-5300, 667-MHz, DDR2) 441075-001 Broadcom 4311AG 802.11a/b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S.

  • Page 40

    Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe 463958-001 65-W HP Smart AC adapter 468824-001 RTC battery for use only in model 2133 482262-001...

  • Page 41

    Spare part Description number 482280-001 Keyboard for use in the United States 482280-031 Keyboard for use in the United Kingdom 482280-041 Keyboard for use in Germany 482280-051 Keyboard for use in France 482280-061 Keyboard for use in Italy 482280-071 Keyboard for use in Spain 482280-081 Keyboard for use in Denmark 482280-091...

  • Page 42

    Spare part Description number 483384-001 8.9-inch, WXGA display assembly for use only with 2133 computer models not equipped camera module (includes 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables) 487330-001 Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S.

  • Page 43

    Spare part Description number 511749-001 Top cover for use only in model 2140 (includes power on switch board and cable, TouchPad board and cable, and wireless on/off switch board and cable) 511750-001 Fan/heat sink for use only in model 2140 (includes replacement thermal material) 511751-001 Plastics/Cable Kit for use only in model 2140 (see spare part number information)

  • Page 44: Preliminary Replacement Requirements, Tools Required, Service Considerations, Plastic Parts

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx8 T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 45: Cables And Connectors, Drive Handling

    Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.

  • Page 46: Grounding Guidelines, Electrostatic Discharge Damage

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.

  • Page 47: Packaging And Transporting Guidelines, Workstation Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

  • Page 48: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 49: Unknown User Password

    Unknown user password If the computer you are servicing has an unknown user password, follow these steps to clear the password: NOTE: These steps also clear CMOS. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 50: Component Replacement Procedures, Serial Number

    Make special note of each screw size and location during removal and replacement. Serial number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.

  • Page 51: Computer Feet

    Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 483382-001 for model 2133, 511752-001 for model 2140. There are 4 rubber feet that are installed on the base enclosure in the locations illustrated below. On model 2133, the rubber feet are attached to the base enclosure by tethers.

  • Page 52: Battery

    Battery Description For use only in model 2133: 6-cell, 55-Wh Li-ion battery 3-cell, 28-Wh Li-ion battery For use only in model 2140: 6-cell, 55-Wh Li-ion battery 3-cell, 28-Wh Li-ion battery Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 53: Keyboard

    Keyboard Keyboards for use in the following countries or regions: Country or region: Brazil Czechoslovakia Denmark Europe France French Canada Germany Greece Hungary Iceland International Israel Italy Japan Latin America Before removing the keyboard, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 54

    Remove the keyboard: Remove the three Phillips PM2.0×3.0 screws that secure the keyboard to the computer. Turn the computer display-side up, with the front toward you. Open the computer as far as possible. Lift the rear edge of the keyboard (1) until it rests at an angle, and then slide it back (2) until it rests on the display assembly.

  • Page 55

    Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and disconnect the keyboard cable (2) from the system board. Remove the keyboard. Reverse this procedure to install the keyboard. Component replacement procedures...

  • Page 56: Memory Module

    Memory module Description For use in model 2133: 2048-MB (PC2-5300, 667-MHz, DDR2) 1024-MB (PC2-5300, 667-MHz, DDR2) 512-MB (PC2-5300, 667-MHz, DDR2) For use in model 2140: 2048-MB (PC2-5300, 667-MHz, DDR2) 1024-MB (PC2-5300, 667-MHz, DDR2) Before removing the memory module, follow these steps: Shut down the computer.

  • Page 57: Mass Storage Device

    Reverse this procedure to install a memory module. Mass storage device NOTE: All hard drive and solid-state drive spare part kits include a bracket and SATA adapter. Description For use only in model 2133: 160-GB, 7200-rpm hard drive 160-GB, 5400-rpm hard drive 120-GB, 7200-rpm hard drive 120-GB, 5400-rpm hard drive 80-GB solid state drive...

  • Page 58

    If you have model 2133, remove the hard drive or solid-state drive: Disconnect the drive cable (1) from the connector on the system board (2). Remove the Phillips PM2.0×5.0 screw (1) and the two PM2.0×5.0 screws (2) that secure the drive to the computer.

  • Page 59

    If you have model 2140, remove the hard drive or solid-state drive: Disconnect the drive cable (1) from the connector on the system board (2). Remove the two PM2.0×5.0 screws (1) that secure the rear of the drive to the computer. Loosen the captive PM2.0×5.0 screw (2) that secures the front of the drive to the computer.

  • Page 60: Top Cover

    Top cover Description Top cover for use only in model 2133 Top cover for use only in model 2140 Before removing the top cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 61

    Turn the computer right-side up, with the front toward you. Open the computer as far as possible. On model 2133, remove the Torx8 T8M2.5×10.0 screw (1) that secures the top cover to the base enclosure, and then lift the rear edge of the top cover (2) and swing it up and forward until it rests upside down in front of the computer.

  • Page 62

    Disconnect the wireless on/off switch board cable (4) from the system board. Remove the top cover. Reverse this procedure to install the top cover. Chapter 4 Removal and replacement procedures...

  • Page 63: Audio Board (model 2133 Only)

    Audio board (Model 2133 only) NOTE: The audio board is available only for model 2133. Audio is integrated into the model 2140 system board. Description Audio board for use only in computer models with WXGA displays Audio board Before removing the audio board, follow these steps: Shut down the computer.

  • Page 64

    Disconnect the audio board cables (3) from the audio board. Remove the audio board. Reverse this procedure to install the audio board. Chapter 4 Removal and replacement procedures...

  • Page 65: Bluetooth Module

    Bluetooth module NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module cable is included in the Plastics/Cable Kit, spare part number 483381-001 for model 2133, 511751-001 for model 2140. See number information. Description For use in all countries and regions except Japan and Asia Pacific countries and regions For use only Japan and Asia Pacific countries and regions...

  • Page 66

    Disconnect the Bluetooth module cable (2) from the Bluetooth module. Remove the Bluetooth module. Reverse this procedure to install the Bluetooth module. Chapter 4 Removal and replacement procedures...

  • Page 67: System Board

    System board NOTE: All system board spare part kits include an ExpressCard assembly, fan/heat sink, processor, RTC battery, and replacement thermal material). Description For use only in model 2133: Equipped with 1.6-GHz processor and only for use with WXGA displays Equipped with 1.2-GHz processor and only for use with WXGA displays Equipped with 1.0-GHz processor and only for use with WXGA displays Equipped with 1.6-GHz processor...

  • Page 68

    Remove the system board: Disconnect the following cables from the system board: (1) Display panel cable (2) Microphone cable (3) Camera module cable (only on computer models equipped with webcam) Remove the wireless antenna cables from the clips built onto the system board. If you have model 2140, go to step 5.

  • Page 69

    Remove the following brackets: (2) (Model 2133 only) Audio/USB connector bracket (3) (Model 2133 and 2140) ExpressCard assembly bracket (4) (Model 2133 only) USB/RJ-45 connector bracket NOTE: For model 2133 only, the audio/USB connector bracket, ExpressCard assembly bracket, and USB/RJ-45 connector bracket are included in the Bracket Kit, spare part number 482266-001. NOTE: For model 2140, the ExpressCard assembly bracket is included in the Plastics Kit, spare part number 511751-001.

  • Page 70

    Lift the right side of the system board (3), and then swing it up and to the left until it rests upside down on the left side of the computer. Disconnect the WLAN antenna cables from the terminals on the WLAN module. NOTE: The black WLAN antenna cable is connected to the WLAN module “Main”...

  • Page 71: Wlan Module

    WLAN module Description Broadcom 4311AG 802.11a/b/g WLAN modules: ● For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,...

  • Page 72

    Description ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,...

  • Page 73

    Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. Remove the battery (see Battery on page Remove the following components: Keyboard (see Keyboard on page Hard drive or solid-state drive (see Top cover (see Top cover on page...

  • Page 74: Rtc Battery

    RTC battery NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared. Description RTC battery for use only in model 2133 RTC battery for use only in model 2140 Before removing the RTC battery, follow these steps: Shut down the computer.

  • Page 75

    Detach the RTC battery (2) from the system board and remove it from the computer. NOTE: The RTC battery is attached to the system board with double-sided tape. If you have model 2140, remove the RTC battery from the socket on the system board. Reverse this procedure to install the RTC battery.

  • Page 76: Fan/heat Sink

    Fan/heat sink Description Fan/heat sink for use only in model 2133 Fan/heat sink for use only in model 2140 Before removing the fan/heat sink, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 77

    Remove the fan/heat sink (2). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink and system board components. Thermal grease is used on the video chip (1) and the surface of the fan/heat sink (1) that contacts the video chip. Thermal tape is used on the processor (2) and the surface of the fan/heat sink (2) that contacts the processor.

  • Page 78

    Remove the fan/heat sink (2). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink and system board components. Thermal grease is used on the video chip (1) and the surface of the fan/heat sink (1) that contacts the video chip. Thermal tape is used on the processor (2) and the surface of the fan/heat sink (2) that contacts the processor.

  • Page 79: Display Assembly

    Display assembly NOTE: All display assembly spare part kits include 2 microphones, 2 speakers, and 2 WLAN antenna transceivers and cables. Description For use in model 2133: 8.9-inch, WXGA display assembly for use only with computer models equipped with camera module 483384-001 8.9-inch, WXGA display assembly for use only with computer models not equipped with camera module 8.9-inch, WSVGA display assembly for use only with computer models equipped with camera...

  • Page 80

    To remove the display assembly for model 2133: Remove the wireless antenna cables (1) from the clips and routing channels built into the base enclosure. CAUTION: The display assembly will be unsupported when the following screws are removed. To prevent damage to the display assembly, support it before removing the screws. Remove the two T8M2.5×5.0 screws (2) and the four Torx8 T8M2.5×10.0 screws (3) that secure the display assembly to the computer.

  • Page 81

    Lift the display assembly (5) straight up and remove it. Reverse this procedure to reassemble and install the display assembly. Component replacement procedures...

  • Page 82: Starting Computer Setup

    Computer Setup Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer.

  • Page 83: Using Computer Setup, Navigating And Selecting In Computer Setup, Restoring Factory Settings In Computer Setup

    Using Computer Setup Navigating and selecting in Computer Setup The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System Configuration menus. Open Computer Setup by turning on or restarting the computer, and then pressing "F10 = ROM Based Setup"...

  • Page 84: Computer Setup Menus, File Menu, Security Menu

    Computer Setup menus The menu tables in this section provide an overview of the Computer Setup options. NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select System information Restore defaults Ignore changes and exit Save changes and exit...

  • Page 85: Diagnostics Menu, System Configuration Menu

    Select System IDs (Windows only) Disk Sanitizer (Windows only) Notebook hard drive password status (Linux only) Diagnostics menu Select HDD Self-Test Options Memory Check System Configuration menu NOTE: Some of the listed System Configuration options may not be supported by your computer. Select Language (Windows only) Boot options...

  • Page 86

    Select Device configurations Built-in device options Port options (Windows only) Chapter 5 Computer Setup To do this ◦ 6th boot device: Network controller ● Swap the functions of the key and left ● Enable/disable USB legacy support. When enabled, USB legacy support allows the following: ◦...

  • Page 87: Computer Specifications, Model 2133

    Specifications Computer specifications, model 2133 Dimensions Depth Width Height (front to back) Weight Equipped with a 3-cell battery, 120-GB hard drive, 1-GB memory, WLAN module, and 2 wireless antennas Equipped with a 3-cell battery, 4-GB solid-state drive, 1-GB memory, WLAN module, and 2 wireless antennas Input power Operating voltage Operating current...

  • Page 88: Computer Specifications, Model 2140, Inch, Sd Display Specifications

    Computer specifications, model 2140 Dimensions Depth Width Height (front to back) Weight Equipped with a 6-cell battery, hard drive Equipped with a 3-cell battery, hard drive Input power Operating voltage Operating current Temperature Operating Nonoperating Relative humidity (noncondensing) Operating Nonoperating Maximum altitude (unpressurized) Operating Nonoperating...

  • Page 89: Inch, Hd Display Specifications, Inch, Wxga Display Specifications

    Pixel resolution Pitch Format Backlight Viewing angle 10.1-inch, HD display specifications Dimensions Height Width Diagonal Surface Treatment Contrast ratio Refresh Rate Brightness Pixel resolution Pitch Format Backlight Viewing angle 8.9-inch, WXGA display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Metric U.S.

  • Page 90

    Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Chapter 6 Specifications Metric U.S. 200 nits (typical) 0.279 × 0.279 mm 1280 × 768 RGB vertical stripe Edge lit 80 × 25 4.0 W ±40 horizontal, +20/–40° vertical (typical)

  • Page 91: Inch, Wsvga Display Specifications

    8.9-inch, WSVGA display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Total power consumption Viewing angle Metric U.S. 11.3 cm 4.45 in 19.5 cm 7.68 in 22.6 cm 8.90 in 6-bit, 262,144 300:1 (typical) 200 nits (typical) 0.1905 ×...

  • Page 92: Hard Drive Specifications

    Hard drive specifications Dimensions Height Width Weight Interface type Transfer rate Security Seek times (typical read, including setting) Single track Average Maximum Logical blocks Disc rotational speed Operating temperature *1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.

  • Page 93: System Dma Specifications

    System DMA specifications Hardware DMA DMA0 DMA1* DMA2* DMA3 DMA4 DMA5* DMA6 DMA7 *ExpressCard controller can use DMA 1, 2, or 5. System function Not applicable Not applicable Not applicable Not applicable Direct memory access controller Available for ExpressCard Not assigned Not assigned System DMA specifications...

  • Page 94: System Interrupt Specifications

    System interrupt specifications Hardware IRQ IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5* IRQ6 IRQ7* IRQ8 IRQ9* IRQ10* IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none. NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port may assert IRQ3 or IRQ4.

  • Page 95: System I/o Address Specifications

    System I/O address specifications I/O address (hex) 000 - 00F 010 - 01F 020 - 021 022 - 024 025 - 03F 02E - 02F 040 - 05F 044 - 05F 062 - 063 065 - 06F 070 - 071 072 - 07F 080 - 08F 090 - 091...

  • Page 96

    I/O address (hex) 220 - 22F 230 - 26D 26E - 26 278 - 27F 280 - 2AB 2A0 - 2A7 2A8 - 2E7 2E8 - 2EF 2F0 - 2F7 2F8 - 2FF 300 - 31F 320 - 36F 370 - 377 378 - 37F 380 - 387 388 - 38B...

  • Page 97: System Memory Map Specifications

    System memory map specifications Size 640 KB 128 KB 48 KB 160 KB 64 KB 15 MB 58 MB 58 MB 2 MB 4 GB 64 KB Memory address 00000000-0009FFFF 000A0000-000BFFFF 000C0000-000CBFFF 000C8000-000E7FFF 000E8000-000FFFFF 00100000-00FFFFFF 04800000-07FFFFFF 04800000-07FFFFFF 08000000-080FFFFF 08200000-FFFEFFFF FFFF0000-FFFFFFFF System memory map specifications System function Base memory...

  • Page 98: Phillips Pm2.0×3.0 Screw

    Screw listing This section provides specification and reference information for the screws and screw locks used in the computer. All screws listed in this section are available in the Screw Kit, spare part number 483383-001 for model 2133, 511753-001 for model 2140. Phillips PM2.0×3.0 screw Color Silver...

  • Page 99: Phillips Pm2.0×5.0 Screw

    Phillips PM2.0×5.0 screw Color Black Where used: 2 screws that secure the mass storage device to the computer (model 2133 is shown) Quantity Length 5.0 mm Thread Head diameter 2.0 mm 5.0 mm Phillips PM2.0×5.0 screw...

  • Page 100: Phillips Pm3.0×3.0 Screw

    Phillips PM3.0×3.0 screw Color Black Where used (model 2140): 4 screws that secure the display assembly to the base enclosure Where used (model 2140): One screw that secures the top cover to the computer Chapter 7 Screw listing Quantity Length 3.0 mm Thread Head diameter...

  • Page 101: Phillips Pm2.0×7.0 Screw

    Phillips PM2.0×7.0 screw Color Black Where used (model 2140): 3 screws that secure the top cover to the computer Where used (model 2140): 4 screws that secure the top cover to the computer Quantity Length 7.0 mm Thread Head diameter 2.0 mm 5.0 mm Phillips PM2.0×7.0 screw...

  • Page 102: Phillips Pm4.5×8.0 Screw

    Phillips PM4.5×8.0 screw Color Silver Where used (model 2140): One screw that secures the display assembly to the base enclosure Chapter 7 Screw listing Quantity Length 8.0 mm Thread Head diameter 4.5 mm 5.0 mm...

  • Page 103: Phillips Pm2.0×8.0 Screw

    Phillips PM2.0×8.0 screw Color Black Where used (model 2140): One screw that secures the display assembly to the base enclosure Quantity Length 8.0 mm Thread Head diameter 2.0 mm 5.0 mm Phillips PM2.0×8.0 screw...

  • Page 104: Torx8 T8m2.0×6.0 Screw

    Torx8 T8M2.0×6.0 screw Color Silver Where used (model 2133): One screw that secures the audio board to the system board Where used: (model 2133) Chapter 7 Screw listing Quantity Length 13 (model 2133) 6.0 mm 5 (model 2140) Thread Head diameter 2.0 mm 4.5 mm...

  • Page 105

    (1) Three screws that secure the audio/USB connector bracket to the system board (2) Two screws that secure the ExpressCard assembly bracket to the system board (3) Two screws that secure the USB/RJ-45 connector bracket to the system board Where used (model 2140): 2 screws that secure the ExpressCard assembly bracket to the system board Where used (model 2133): 5 screws that secure the fan/heat sink to the system board Where used (model 2140): 3 screws that secure the fan/heat sink to the system board...

  • Page 106: Torx8 T8m2.5×5.0 Screw

    Torx8 T8M2.5×5.0 screw Color Black Where used (model 2133): One screw that secures the mass storage device to the computer Chapter 7 Screw listing Quantity Length 4 (model 2133) 5.0 mm 2 (model 2140) Thread Head diameter 2.5 mm 5.0 mm...

  • Page 107

    Where used (model 2140): One captive screw that secures the mass storage device to the computer Where used: One screw that secures the WLAN module to the system board Torx8 T8M2.5×5.0 screw...

  • Page 108

    Where used (model 2133): 2 screws that secure the display assembly to the base enclosure 100 Chapter 7 Screw listing...

  • Page 109: Torx8 T8m2.5×10.0 Screw

    Torx8 T8M2.5×10.0 screw Color Silver Where used (model 2133): 3 screws that secure the top cover to the computer Where used (model 2133): One screw that secures the top cover to the computer Quantity Length 10.0 mm Thread Head diameter 2.5 mm 5.0 mm Torx8 T8M2.5×10.0 screw 101...

  • Page 110: Torx8 T8m2.0×4.0 Screw

    Where used (model 2133): 4 screws that secure the display assembly to the base enclosure Torx8 T8M2.0×4.0 screw Color Silver Where used (model 2133): One screw that secures the top cover to the computer 102 Chapter 7 Screw listing Quantity Length 4.0 mm Thread...

  • Page 111: Backup And Recovery In Windows Vista, Backing Up And Recovering, Backing Up

    Backup and recovery Backup and recovery in Windows Vista Backing up and recovering To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.

  • Page 112: Recovering

    Software not installed at the factory must be reinstalled. Personal files must be restored from a backup. If possible, back up all personal files. If possible, check for the presence of the HP Recovery partition. To find the partition, click Start, and then click Computer.

  • Page 113: Backup And Recovery In Windows Xp, Backing Up And Recovering, Backing Up, Recovering

    The recovery process reinstalls the original operating system as well as software and drivers. Software, drivers, and updates not installed by HP must be manually reinstalled. Personal files must be restored from a backup. If possible, back up all personal files.

  • Page 114: Backup And Recovery In Suse Linux Enterprise Desktop, Performing A Recovery

    Using have created and any software installed on the computer are permanently removed. The tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled. To recover the original hard drive image using f11, follow these steps: If possible, back up all personal files.

  • Page 115: Audio-out (headphone), Audio-in (microphone)

    Connector pin assignments Audio-out (headphone) Audio-in (microphone) Signal Audio out, left channel Audio out, right channel Ground Signal Audio signal in Audio signal in Ground Audio-out (headphone) 107...

  • Page 116: External Monitor

    External monitor 108 Chapter 9 Connector pin assignments Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock...

  • Page 117: Rj-45 (network), Universal Serial Bus

    RJ-45 (network) Universal Serial Bus Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused Signal +5 VDC Data - Data + Ground RJ-45 (network) 109...

  • Page 118: Requirements For All Countries And Regions

    10 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.

  • Page 119: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan Korea The Netherlands Norway The People's Republic of China Sweden Switzerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

  • Page 120: Recycling Battery, Display

    NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.

  • Page 121

    Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.

  • Page 122

    Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.

  • Page 123

    Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.

  • Page 124

    Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight frame from the display panel.

  • Page 125

    Remove the backlight from the backlight frame. Disconnect the display panel cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.

  • Page 126: Index

    Index AC adapter, spare part number 29, 32 antenna disconnecting 62 locations 5 antennas, model 2133 12 antennas, model 2140 20 audio board removal 55 spare part number 24, 32, 34, 55 audio, product description 2 audio-in jack location 10 pin assignments 107 audio-out jack location 10...

  • Page 127

    electrostatic discharge 38 embedded numeric keypad keys, identifying 14 esc key 6 esc key, identifying 14 Ethernet, product description 2 ExpressCard assembly bracket illustrated 28 removal 61 ExpressCard slot 9 ExpressCard slot bezel 29 ExpressCard slot, identifying 17 external media cards, product description 2 external monitor port location 10...

  • Page 128

    microphone jack 107 monitor port 108 network jack 109 RJ-45 jack 109 Universal Serial Bus (USB) port 109 plastic parts 36 Plastics/Cable Kit contents 29 spare part number 25, 29, 33, 35 pointing device components, model 2133 7 components, model 2140 15 illustrated 7, 15 pointing device components TouchPad 7...

  • Page 129

    system information 76 system memory map 89 system restore points 103 thermal material, replacement 69 tools required 36 top components 5 top cover removal 52 spare part number 24, 32, 35, 52 TouchPad buttons 15 identifying 15 scrolling regions 15 TouchPad buttons 7 TouchPad components, model 2133 7...

Comments to this Manuals

Symbols: 0
Latest comments: