Sanwa MT-R RX-493i User Manual page 3

Safe Handling and Precautions
Note Precautions for Safe Use
Warning
● 2.4 GHz frequency band is not only used for radio control. This frequency band
is shared with ISM (Industry, Science and Medical) band. It can be affected by
microwave ovens, wireless LAN, digital cordless telephones, audio equipment,
Bluetooth of game machines or cell phones and short-range communication such
as VICS. Also, be cautious about being affected by amateur radio and premises
radio stations for moving body identification since this frequency band is used for
them as well. When a harmful radio frequency interference is done to an existing
radio station, stop the transmission of the radio frequency immediately and take a
measure to avoid the interference.
● For RC circuit, minimize the use of equipment that can affect 2.4 GHz systems and
make sure to check the safety beforehand. Also, follow the instruction of the facility
manager.
● When operating the models behind a building or a steel tower, blocking the direction
of radio wave transmission can cause reduction of operation response or loss of
control. Always operate within the range you can visually check.
● Don't grab the transmitter antenna. Doing so can be dangerous since it can weaken
the radio signal output and narrow the range of operation.
● Don't attach any metal parts around the antenna of the transmitter.
● If you have the transmitter's antenna extremely close to a servo or speed controller
other than the receiver, it can cause malfunction but it is an influence of a strong high
frequency output and it is not abnormal.
● The receiver is a precise instrument. Don't subject it to strong impact or vibrations.
Use a thick sponge to prevent vibrations.
● Keep the antenna wire of the receiver out as much as possible. And keep it straight
and stretched. Don't cut the extra length of the antenna line or bend it.
● Keep the antenna wire of the receiver out as much as possible. And keep it straight
and stretched. Don't cut the extra length of the antenna line or bend it.
● Don't place the antenna wire of the receiver close to a electrical noise source like a
motor wire or a battery wire.
● When installing the receiver on a metallic chassis or a carbon chassis, use layers of
double adhesive tape pieces to keep the receiver from touching the chassis as much
as possible.
3
INDEX
■Structure and the Standard of the Set・・・・・・・・・・・・・・・・・・・・・・・5
●Structure of The Set (5)
●Set Specification (5)
■Before Using・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・6-7
●Adjusting Tension of The Steering and Throttle (6)
●Adjusting The Adjustable Trigger (7)
●About The Power Source, Bind (7)
■Names of Each Part of The Transmitter・・・・・・・・・・・・・・・・・・・・・・8
■Connections and Installation of Receiver ・・・・・・・・・・・・・・・・・・・・・9,10
●About Receiver, And How to Handling The Antenna (9)
●About Connection Setup (10)
■Before Driving A RC Car・・・・・・・・・・・・・・・・・・・・・・・・・・・・・13-16
●How To Place Servo Horn (13)
●How To Set Reverse [REV] (13)
●How To Set Sub Trim [SUB-T] (14)
●Sub Trim and Trim Differences (14)
●How To Set End Point Adjustment [EPA] (15)
●How To Set Dual Rate [D/R] (16)
■How To Use Each Feature・・・・・・・・・・・・・・・・・・・・・・・・・・・11,12,17-52
●About Key Operation (11)
●About the Display Panel (12)
●About the Menu Structure (17)
●Setting [SETTING] (18-34)
・Dual Rates (D/R] (18)
・Speed [SPEED](19)
・Curve [CURVE] (20)
・Fail Safe [F/S] (21)
・Base [BASE] (22-24)
・Reverse [REV] (22)
・Sub Trim [SUB-T] (22)
・End Point Adjustment [EPA] (23-24)
・Function [FUNC] (25-28)
・Trim [TRIM] (25)
・Anti-Lock Brake [ALB] (26)
・Offset [OFFSET] (27)
・Throttle Type [TH TYPE] (28)
●AUX [AUX] (29-34)
・Step AUX [STEP AUX] (29)
・Point AUX [POINT AUX](30)
・4 Wheel Steering [4WS] (31)
・Motor On Axle [MOA] (32)
・AUX Mixing [AUX-MIX] (33)
・Code AUX [CODE AUX] (34)
■Assign Function List ・・・・・・・・・・・・・・・・・・・・・・・・・・ 53
■Transmitter LED Indication List ・・・・・・・・・・・・・・・・・・・・・ 54
■Index・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・55
■When this happens... ・・・・・・・・・・・・・・・・・・・・・・・・・・56
■Service and Support ・・・・・・・・・・・・・・・・・・・・・・・・・・57
■FCC Compliance Statement・・・・・・・・・・・・・・・・・・・・・・・58
●Model [MODEL] (35-38)
・Model Select [MODEL SELECT] (35)
・Model Name [MODEL NAME](36)
・Model Copy [MODEL COPY] (37)
・Model Clear [MODEL CLEAR] (38)
●Timer [TIMER] (39-40)
・Lap Timer [LAP TIMER] (39)
・Interval Timer [INT TIMER](40)
・Down Timer [DOWN TIMER] (40)
●Telemetry [TELEMETRY] (41-42)
・Logger[LOGGER] (41)
・Alert Setting [ALERT SETTING] (42)
・Telemetry Setting [TELEMETRY SETTING](42)
●System [SYSTEM] (43-48)
・Bind [BIND] (43-44)
・Key Assign Switch [KEY ASSIGN SW](45)
・Key Assign Trim [KEY ASSIGN TRIM] (46)
・Buzzer [BUZZER] (47)
・Battery [BATTERY] (47)
・LCD [LCD] (48)
・Calibration [CALIBRATION] (48)
●Setup Wizard (49-50)
●About Quick Setup Wizard (51-52)
4