Timer Menu; Lap Timer; Down Timer - Sanwa MT-R RX-493i User Manual

How to Use Each Feature

TIMER MENU

● It has three timer features including Lap Timer, Interval Timer and Down Timer.
● When selecting a timer and operate the up and down key, you can toggle between the timer screen and
the setting screen.
ENTER BACK
<SET Display>
● You can measure and record each lap up to 99 laps (works for all models).
● Pre Alarm (PRE-ALM) is installed and the alarm goes off before the goal.
1) Select [TIMER] with up and down key. Determine with the Enter operation.
2) Change [SET] menu with enter.
*Switch SET to LAP with up and down key.
3) TYPE setting
Change [LAP] on TYPE setting with up and down key.
Determine with enter.
4) Goal Time setting
Set goal time [ALRM] with up and down key.
○ Setting Range: 00:01 ~ 99:59 (unit: 00:01 each)
○ Default: 05:00
5) As the default, timer swith is set on SW1.
Holding SW1 will standby timer.
Then when push SW1 again or operating throttle,
timer will be started.
6) After starting timer, lap time is recorded when pushing SW1.
After pushing SW1, the switch will not work while 3 seconds.
7) Completing measuring
By holding SW1, measuring will be completed.
Or pushing SW1 after finished goal time will complete measuring.
*When turning the power switch off while the timer is activated,
the timer will be reset.
*When the timer is set to SW1, the timer will be in the standby
mode by holding the switch even on a screen other than
the TIMER setting screen.
39
TIMER
⇔
UP Key
Down Key
<LAP Display>
●Lap display can be checked measured lap time.
●Select Lap with up and down key during stopping lap timer.
*The fastest lap in the measured lap time will be shown [BEST].

LAP TIMER

ENTER BACK
Shortcut to Key Assign
Switch Type
Switch SET to LAP with up and down key.
Select SET with enter.
Switch 1
(SW1)
Sw3
Sw1
INTERVAL TIME [INT TIMER]
● It activates the alarm at the time set at the beginning of running and uses it as the guideline for the lap
time.
1) Select [TIMER] with up and down key.
Determine with the Enter operation.
2) Change [SET] menu with enter.
*Switch SET to LAP with up and down key.
3) Setting the Type [TYPE]
Select [INT] with up and down key. Determine with enter.
4) Setting Interval (INTERVAL)
Set the Interval Timer.
○ Setting Range: 00:00.01 ~ 99:59.99
○ Default: 00:00.00
*Interval timer will not work for 00:00.00.
5) As the default, timer swith is set on SW1.
Holding SW1 will standby timer.
Then when push SW1 again or operating throttle,
timer will be started.
6) After starting timer, lap timer will be reset when pushing SW1.
7) Completing measuring
By holding SW1, measuring will be completed.
After finished goal time, pushing SW1 will be lap timer reset.
*When turning the power switch off while the timer is activated, the timer will be reset.
*When the timer is set to SW1, the timer will be in the standby mode by holding the switch even on a
screen other than the TIMER setting screen.

DOWN TIMER

● It can be for calculating running time of an electric RC car and the fuel comsumption of an engine RC car.
● You can set for per second up to 99 : 59.
● When the timer switches to Up Timer after Down Timer ends, you can check lap time after the end.
1) Select [TIMER] with up and down key.
Determine with the Enter operation.
2) Change [SET] menu with enter.
*Switch SET to LAP with up and down key.
3) Setting the Type [TYPE]
Select [DOWN] with up and down key. Determine with enter.
4) Set the Interval Timer.
○ Setting Range: 00:01 ~ 99:59
○ Default: 05:00
*Down timer will work as up timer for 00:00.
5) As the default, timer swith is set on SW1.
Holding SW1 will standby timer.
Then when push SW1 again or operating throttle,
timer will be started.
6) After starting timer, down timer will be reset when pushing SW1.
7) Completing measuring
By holding SW1, measuring will be completed.
*When turning the power switch off while the timer is activated, the timer will be reset.
*When the timer is set to SW1, the timer will be in the standbymode by holding the switch even on a
screen other than the setting screen.
ENTER BACK
Shortcut to Key Assign
Switch Type
Switch SET to LAP with up and down key.
Select SET with enter.
ENTER BACK
Shortcut to Key Assign
Switch Type
Switch SET to LAP with up and down key.
Select SET with enter.
40