Sanwa MT-R RX-493i User Manual page 24

How to Use Each Feature
SYSTEM MENU
● A feature for setting system of the transmitter, such as Bind, Key Assignments (KEY ASSIGN),Buzzer,
Battery, LCD and CALIBRATION.
Switch and Trim position
TRIM 2
(TRM 2)
SWITCH 3
(SW 3)
Sw3
Sw1
SWITCH 1
(SW 1)
KEY ASSIGN SWITCH
● You can assign features to the switches (SW1, SW2, SW3) of the transmitter and toggle ON/OFF of the
features during operation.
1) Select [SYSTEM] with up and down key.
Determine with the Enter operation.
2) Select [KEY ASSIGN] with up and down key.
Determine with the Enter operation.
3) Setting the Switch (SW1/SW2/SW3)
Operate the Enter with [SW] and set the feature
to assign to the switch with up and down key.
○ Setting Range:
Switch Assignable Futures
OFF, ASIST-ST, D/R-ST, D/R-TH, D/R-BR, CUR-ST, CUR-TH, SPD-ST, SPD-TH,
SW1
ALB, OFFSET, AUX1, AUX2, TIMER, TE-CLR, LOGGER
Switch Assignable Futures
OFF, ASIST-ST, D/R-ST, D/R-TH, D/R-BR, CUR-ST, CUR-TH, SPD-ST, SPD-TH,
SW2
ALB, OFFSET, AUX1, AUX2
Switch Assignable Futures
OFF, D/R-ST, D/R-TH, D/R-BR, CU-R-ST, CU-R-TH, CU-R-BR, SP-ST-F, SP-ST-R,
SP-TH-F, SP-TH-R, ALB-ST, ALB-LG, ALB-CY, OFFSET,
SW3
AUX1(CD1～10), AUX2(CD1～10)
○ Default : SW1: TIMER SW2: OFF
*BY Setting [ASSIST-ST] onto SW1 and SW2,
you can turn ON/OFF the feature of D/R, SPEED and CURVE
that can be set onto the steering.
4) Setting Mode
It sets the switch performance but there are casesthat
you cannot set depending on the feature to assign.
○ Setting Range
TOGGLE (Switching between ON/OFF when pressed every time)
PUSH (ON is worked when switch is only pressed)
45
SYSTEM
TRIM 1
(TRM 1)
Features assigned to the Switch and Trim
at the factory
TR1: Steering Trim(TRM-ST)
TR2: Throttle Trim(TRM-TH)
TR3: Dual Rate ST(D/R-ST)
SWITCH 2
SW1: TIMER
(SW 2)
SW2: AUX1
SW3: AUX2
TRIM 3
(TRM 3)
ENTER
ENTER
SW3: OFF
About MODE Setting for SW3
①
TWEAK1
Neutral
TWEAK2 P1 Neutral
P1/P2 can be changed freely.
● You can change the setting value of each feature with Trim1 - Trim3.
● You can also change the setting of the variation change in one time of Trim operation with the STEP
setting and the direction of the action with the REV setting.
1) Select [SYSTEM] with up and down key.
Determine with the Enter operation.
2) Select [KEY ASSIGN] with up and down key.
Determine with the Enter operation.
3) Setting Trim (TRM1/TRM2/TRM3)
Select [TRIM] with enter. Change the setting
and set a feature to assign with up and down key.
○ Setting Range:
Switch
TRIM1
OFF、TRIM-ST, TRM-TH, TRIM-A1, TRIM-A2, D/R-ST, D/R-TH, D/R-BR, CU-R-ST, CU-R-TH, CU-R-BR,
TRIM2 SP-ST-F, SP-ST-R, SP-TH-F, SP-TH-R, ALB-PO, ALB-ST, ALB-LG, ALB-CY, OFFSET,
AUX1(CD1～10), AUX2(CD1～10)
TRIM3
○ Default:
4) Setting Step
Set the variation of the movement by one-time Trim operation.
Select [STEP] with up and down key. Determine with the Enter operation and set the variation.
○ Setting Range: 1～100
○ Default:
BACK
5) Setting the Direction of Action
Set the direction of action when operating Trim. Select [REV] with up and down key.
Determine with the Enter operation and set the direction of action.
○ Setting Range: NOR/REV
○ Default:
BACK
② ③
P1 P2
P2
KEY ASSIGN TRIM
Assignable Futures
TR1:TRM-ST
TR2:TRM-TH
TR3:D/R-ST
5
NOR
46