Function [Func] - Sanwa MT-R RX-493i User Manual

How to Use Each Feature

FUNCTION [FUNC]

● Function can set trim, ALB (Anti-Lock Brake), OFFSET, and TH TYPE (Throttle Type) on each channel.
● Correct neutral (center) of each channel (ST/TH/A1/A2) with Trim.
● As default, steering is set for Trim 1 (TRM1), and throttle for Trim 2 (TRM2).
1) Select a channel (ST/TH/AUX1/AUX2) for
adjusting Trim with up and down key.
2) Determine with Enter operation and adjust
with up and down key.
○ Setting Range:
ST:L100～R100
TH:H100～B100
AUX1:H100～L100
AUX2:H100～L100
○ Default:
ALL : 0
*Make an adjustment with TRM1 (ST) and TRM2 (TH)
during operation.You can change the Trim lever position
with the Key Assignments Trim feature (P. 46).
• About Trim
IMPORTANT
Trim is a feature to adjust the neutral (center) position of the servos. After installing
the steering servo onto a car, you can adjust with Trim when the car does not move straightly. Neutral
position adjustment is necessary not only after installing the servo but for changes that happen
during running such as tire wears and chassis twist.
• It's Sub Trim that adjusts het center position when adjusting linkage (P. 22)
• If Trim and Sub Trim are off to one side, it causes dead band (the range the servo does not
move) to the steering wheel and the throttle trigger. When installing the servo horn, fix the
Note
servo horn as close to the center as possible and center it with Sub Trim.
25
SETTING
TRIM
TRIM 1
(TRM 1)
Sw3
Sw1
TRIM 2
(TRM 2)
ANTI-LOCK BRAKE [ALB]
● Anti-Lock Brake enables stable braking on a low grip road.
● Because of the stable braking, you can drive ideal cornering lines as intended.
1) Select [ALB] with up and down key.
2) The menu changes to ALB setup menu
with the enter operation.
3) Setting Stroke (STROKE)
Set Stroke of ALB with up and down key.
Stroke is the width of repeated actions
at the time of braking.
○Setting Range:OFF, 0%～100%
○Default:OFF *ALB does not work when it is off.
4) Setting Point (POINT)
Set Point of ALB with up and down key.
Point is the position where ALB starts acting
when operating the brake.
○Setting Range: 5%～100%
○Default: 80%
5) Setting Lag (LAG)
Set Lag of ALB with up and down key.
Lag is a setting of time lag from the time
when operating to the point to the time
when ALB starts acting.
○Setting Range: 0.00s～1.00s
○Default: 0.00s
6) Setting Cycle (CYCLE)
Set a cycle of ALB with up and down key.
Cycle is a frequency setting of
repeated actions for braking.
○Setting Range: 0.01s～1.00s
○Default: 0.03s
*While Anti-Lock Brake working, transmitter LED will be
high-speed flashing.
*LED flashing time and way of flashing are same
in any setting values.
SUPPLEMENT
• Activate the brake rather strongly not to the extent that the tires of your RC car lose their grips (not to
slip) and adjust so that Anti-Lock Brake is activated just before the tires are locked and slide.
• If you set ALB using a speed controller with a back on an RC car, you may not able to operate back
movement. When using a back movement, turn ALB off.
ENTER BACK
Trigger indicator
Point Position
ALB will be worked when trigger
[ ]
operation is right side (Brake side)
Lag
Cycle
Duty
(A:B ratio)
Duty A : brake ON
Duty B : brake OFF
Brake operation
Full Brake
Position of the Point
Neutral
*ALB is activated when operating from the point
position to full brake.
26