Sanwa MT-R RX-493i User Manual page 11

How to Use Each Feature
SPEED
● Features to control the speed of the servos used for steering and throttle. By setting, the RC car is not
affected even when doing a sudden operation. On the steering side, smooth corner work becomes
possible and on the throttle side, stable rising from a corner by throttle work with saved power.
*When setting AUX TYPE to [CODE], adjusting the speed feature of the AUX channel does not affect the
performance.
*When setting the speed of the AUX channel, do so using steering/throttle as a reference.
[ ST ]
STEERING SPEED
● A feature to delay the speed of the steering servos against the steering operation. You can set speed for steering
forward and returning individually. For steering operation slower than setting, the speed feature does not work.
1 ) [ST (Steering)] with up and down key.
2 ) Setting on the forward side [FORWARD]
Select [FORWARD] with the Enter key and adjust
the setting value by up and down key.
*When cancelling a selected feature, use the Back key.
○Setting Range: 0～-100
○Default: 0
3 ) Setting on the Return side [RETURN]
Select [RETURN] with the Enter key and adjust
the setting value with by up and down key.
○Setting Range: 0～-100
○Default: 0
*Adjust during actual operation. When not using the features or when a setting value cannot be determined
even after adjustment, set the value to 0% (linear).
• For driving an RC car, steering operation that suits the movement of the RC car is important and
excessive operation is not recommended. Steering speed can minimize unnecessary operation
SUPPLEMENT
and enables smooth cornering.
• When steering speed and steering curve are combined, the effect is doubled.
[ TH ]
THROTTLE SPEED
● A feature to slow down the performance speed of the throttle servos and delay the response of the speed
controller against throttle operation. You can set speed for entering throttle (Forward) and returning
(Return) individually. The speed feature does not work with throttle operation slower than the setting.
*Setting is only for High side and Brake side cannot be set.
1 ) Select [TH (Throttle)] with up and down key.
2 ) Setting on the forward side [FORWARD]
Select [FORWARD] with the Enter key and adjust
the setting value by up and down key.
*When cancelling a selected feature, use the Back key.
○Setting Range: 0～-100
○Default: 0
3 ) Setting on the Return side (RETURN)
Select [RETURN] with the Enter key and adjust the setting
value by up and down key.
○Setting Range: 0～-100
○Default: 0
*Adjust during actual operation. When not using the features or when a setting value cannot be determined
even after adjustment, set the value to 0% (linear).
• For driving an RC car, throttle operation that suits the movement of the RC car is important
and excessive operation is not recommended. Throttle SPEED can minimize unnecessary
SUPPLEMENT
operation and enables smooth performance.
• When throttle SPEED and throttle CURVE are combined, the effect is doubled.
19
SETTING
FORWARD FORWARD
RETURN RETURN
Ｎ
FORWARD
RETURN
Ｎ
Ｈ
End
Neutral
CURVE
● Curve changes servo work rate by steering and throttle position. It responds quickly when the set value is
on plus (+) side whereas it responds mildly when the set value is on minus (-) side.
● MT-R has adjustable rate controller (ARC) of linear position.
*If the AUX type is set to [CODE], curve does not work.
*Please adjust curve setting on AUX cannel to refer steering and throttle.
Adjustable rate controller (ARC)
Position at where operation is variable can be changed by adjusting the setting of POINT.
Quick Quick
Normal
Mild
Steering Wheel L End Operating Quantity Steering Wheel R End Operating Quantity
Neutral Position
Throttle Trigger H End Operating Quantity Throttle Trigger B End Operating Quantity
[ ST ]
STEERING CURVE
● You can change the steering feature from Mild to Linear and to Quick.
If you find your RC car oversteering, change the setting to the minus side and if you find understeering,
change to the plus side. Steering Adjustable Rate Control is a simultaneous setting for L and R.
1) Select ST with up and down key.
2) Setting Rate [RATE]
Select [RATE] and adjust the setting value with up and down key.
*When cancelling a selected feature, use the Back button.
○Setting Range: -100～100% ○Default: 0%
3) Setting Point [POINT]
Select [POINT] and adjust the setting value with up and down key.
○Setting Range: 5～95% ○Default: 50%
[ TH ]
THROTTLE CURVE
● You can change the throttle feature from Mild to Linear and to Quick.
In general, when operating on a slippery road or if you find over powering, change the setting to the minus
side. When operating on a high-grip road or if you find lack of power in the power unit, change to the plus
side. You can set the High side and the brake side separately.
*Selection of the High side and the brake side is done by trigger operation.
1) Select TH with up and down key.
2) Setting Rate [RATE]
Select [RATE] with with up and down key.
Adjust the setting value.
○Setting Range: -100～100% ○Default: 0%
3) Setting Point [POINT]
Select [POINT] with up and down key.
Adjust the setting value.
○Setting Range: 5～95% ○Default: 50%
*When cancelling a selected feature, use the Back button.
1.If you feel slippy while driving drift car, please set High side point 20 to 30% and Rate -15 to - 30%. It can
be more smooth and getting traction easily. *Please arrange ideal point and rate values while driving.
2. In case of using motor of stock class, please set High side point 20 to 30% and Rate 15 to 30%. It would
give quick throttle timing and get more car acceleration.
SETTING
Normal
Mild
Point Setting Position
Select H/B by Throttle Trigger
Point Setting Position
20