Sanwa MT-R RX-493i User Manual page 13

How to Use Each Feature
BASE
● Base sets multiple functions all at once such as the Reverse that determines the direction of the servo of
each channel, the speed controller according to a specific RC car, the Sub Trim that adjusts the neutral
position, and the End Point Adjustment [EPA].
END POINT ADJUSTMENT [ EPA ]
● EPA setting can adjust left and right steering servo range for steering operation, high and brake throttle
working range for throttle trigger operation, and the servo working range for AUX1, AUX2 (3ch, 4ch).
[ ST-EPA ]
STEERING END POINT ADJUSTMENT
● Due to linkage, suspension balance and the difference of the tire diameter, left and right cornering radius
can be different. In case of this, this feature adjusts the servo working range of left and right so that left and
right cornering radius can be the same.
1) Before adjusting Steering End Point Adjustment (ST-EPA),
make a neutral adjustment of the servo (P.22).
Neutral adjustment is to align the center position with
Sub Trim by turning the power on and installing
the servo horn in the approximate center position.
2) Select either of [EPA-L/EPA-R] with up and down key
Determine with the Enter.
3) Adjust the working range with
up and down key.
*When the cursor is on either of
EPA-L/EPA-R, it is also possible to
move the cursor by steering operation.
○Setting Range:L/R 0%～150%
○Default: L/R 100%
[ TH-EPA ]
THROTTLE END POINT ADJUSTMENT
● It adjusts the High Point of FET Speed Controller, Brake Point, carburetor of engine and the brake working
range.
1) For a nitro car, make a neutral adjustment of the servo (P.20) before adjusting
the Throttle End Point Adjustment (TH-EPA).
Neutral adjustment is to align the center position with Sub Trim
by turning the power on and installing the servo horn in
the approximate center position.
2) Select [TH/Throttle] with up and down key.
3) Select either of [EPA-H/EPA-B] with up and down key.
Determine with the Enter.
4) Adjust the operating quantity with up and down key.
When adjusting ESC / FET Speed Controller, normally set
both the high side and the brake side to 100% and set
neutral, high point and brake point on the ESC / FET Speed
Controller side (Setting method is different depending on
the ESC / FET Speed Controller).
*When the cursor is on either of
EPA-H/EPA-B, it is also possible to
move the cursor by trigger operation.
○Setting Range:H/B 0%～150%
○Default: H/B100%
23
SETTING
*Make sure the servos do not lock to make clicking sound
• If the linkage is locked for
a long period, it can cause
Note
the servo breakage.
*Make sure the servos
do not lock to make
clicking sound
• When EPA setting value is
too large on the fully open
side of the carburetor and
Note
the brake side for throttle
linkage, the servo is locked
and it can cause the motor
malfunction and runaway.
[ ]
AUX1・END POINT ADJUSTMENT
AUX1-EPA
● You can use AUX1 for functions of accessories and adjust the maximum steering angle with EPA. Since
you can set H/L separately, precise adjustment is possible.
*When setting AUX1 to [CODE5/CODE10] in AUX TYPE, the operation will not be refected even by
adjusting EPA.
1) Before adjusting AUX1 End Point Adjustment (A1-EPA), make a neutral adjustment of the servo (P. 22).
Neutral adjustment is to align the center position with SubTrim by turning the power on and installing the
servo horn in the approximate center position.
2) Select [AUX1] with up and down key.
3) Select either of [EPA-H/EPA-L] with up and down key.
Determine with the Enter.
4) Adjust the working range with up and down key.
○Setting Range:H/L 0%～150%
○Default: H/L100%
[ ]
AUX2・END POINT ADJUSTMENT
AUX2-EPA
● You can use AUX2 for functions of accessories and adjust the maximum steering angle with EPA. Since
you can set H/L separately, precise adjustment is possible.
*When setting AUX2 to [CODE5/CODE10] in AUX TYPE, the operation will not be reflected even by
adjusting EPA.
1) Before adjusting AUX2 End Point Adjustment (AUX2-EPA), make a neutral adjustment of the servo (P. 22).
Neutral adjustment is to align the center position with Sub Trim by turning the power on and installing the
servo horn in the approximate center position.
2) Select [AUX2] with up and down key.
4) Select either of [EPA-H/EPA-L] with up and down key.
Determine with the Enter.
3) Adjust the working range with up and down key.
○Setting Range:H/L 0%～150%
○Default: H/L100%
24