Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
I C
COM 1
RS232/422/485
Select (JP7)
2
6
2
6
PS/2 KB/MS
JP33
COM 1 RS232/Power Select (JP9)
USB 5-6
1
1
5
1
5
COM 1
2
2
USB 2.0
6
6
RS232/422/485
COM 1 RS232/422/485 Select (JP8)
Select (JP10)
1
5
1
5
4
1
8
5
+12V
COM 1
Socket LGA1151
Power
VGA
PTN3355
DVI-I (DVI-D signal)
DP++
1
JP31
LAN 1
USB 1-2
USB 3.0
Intel I219V (for KD330-H110)
Intel I219LM (for KD330-Q170)
LAN 2
USB 3-4
LAN 1
USB 3.0
Intel
I211AT
Line-out
Mic-in
JP32
PCIe 1 (PCIe x16 )
1
Realtek
PCI 1
ALC888S
S/PDIF
1
5
Buzzer
PCIe 2 (PCIe x4)
COM 7
COM 8
(optional)
(optional)
Nuvoton
1
9
1
9
iTE
NCT5104D
IT8893E
(optional)
2
2
USB 3.0
COM 9
COM 10
USB 5-6
DIO
(optional)
(optional)
(for KD330-Q170 only)
9
1
9
1
19
1
11
2
10
2
2
Chapter 2 Hardware Installation
Chapter 2
(DDR4_2, DDR4_4 for KD330-Q170 only)
DDR4_2
DDR4_4
1
3
1
4
DDR4_1
DDR4_3
System Fan 1
CPU Fan
LPC
TPM (optional)
14
13
2
1
12
24
ATX
Power
Standby
Power LED
1
13
1
2
Front Panel
11
1
2
LAN LED
Clear CMOS
Battery
7
8
SPI Flash
Data (JP1)
BIOS
3
1
1
3
Mini PCIe Signal Select (JP6)
Chassis
1
(for KD330-Q170 only)
Intrusion
Mini PCIe
2
(for KD330-Q170 only)
SATA 3.0
Intel
1
7
SATA 0
1
7
H110/Q170
SATA 1
Nuvoton
1
7
NCT6106D
SATA 2
1
5
1
7
JP35 JP34
6
5
SMBus
(JP13)
(JP12)(JP11)
2
1
2
SATA 3
1
1
2
6
2
6
2
6
(JP14)
USB 2.0
1
5 1
5 1
5
USB 9-10
USB 7-8
1
9
1
1
9
1
1
9
9
1
1
9
1
1
2
2
3
10
10
2
2
2
2
2
COM 5
COM 2
COM 3
COM 4
COM 2 RS232/422/485 Select (JP11)
COM 2 RS232/422/485 Select (JP12)
COM 2 RS232/422/485 Select (JP13)
COM 2 RS232/Power Select (JP14)
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
System Memory
Important:
When the Standby Power LED lights red, it indicates that there is power on the
system board. Power-off the PC then unplug the power cord prior to installing any de-
vices. Failure to do so will cause severe damage to the motherboard and components.
PS/2 KB/MS
LAN 1
LAN 1
Features
•
Two 288-pin DIMM up to 32GB (KD330-H110)
Four 288-pin DIMM up to 64GB (KD330-Q170)
•
Dual Channel DDR4 2133/2400 MHz
9
DDR4_4
(for KD330-Q170 only)
DDR4_3
DDR4_2
(for KD330-Q170 only)
Standby Power LED
DDR4_1
www.dfi.com
Advertisement
Table of Contents
