Table Of Contents; Fcc Information - Icom ID-RP2C Instruction Manual

FCC INFORMATION

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.

TABLE OF CONTENTS

IMPORTANT ............................................................. i
EXPLICIT DEFINITIONS ........................................... i
PRECAUTIONS ......................................................... i
FCC INFORMATION .................................................ii
1 SYSTEM OUTLINE .............................................. 1
■ ID-RP2C............................................................ 1
■ ID-RP2D............................................................ 1
■ ID-RP2V ............................................................ 1
■ AH-108: 1.2 GHz Collinear antenna ................. 1
2 SUPPLIED ACCESSORIES ................................ 2
■ Accessories for ID-RP2C ................................. 2
■ Accessories for ID-RP2D/ID-RP2V ................... 2
■ Accessories for AH-108 .................................... 2
3 PANEL DESCRIPTIONS ................................. 3-5
■ ID-RP2C (Front panel) ...................................... 3
■ ID-RP2C (Rear panel)....................................... 3
■ ID-RP2D (Front panel) ...................................... 4
■ ID-RP2D (Rear panel)....................................... 4
■ ID-RP2V (Front panel) ...................................... 5
■ ID-RP2V (Rear panel) ....................................... 5
4 INSTALLING AND CONNECTING .................. 6-8
■ Attaching an "N" connector ............................... 6
■ Power supply requirements .............................. 6
■ Installing in a system rack ................................. 6
■ Attaching the rubber feet .................................. 6
■ Grounding ......................................................... 6
■ System connections .......................................... 7
■ Antenna assembling ......................................... 8
D AH-108 .......................................................... 8
5 DRIVER INSTALLATIONS ............................ 9-17
®
■ Microsoft Windows
■ Microsoft ® Windows
■ Checking the COM port ................................. 14
D Microsoft ® Windows
D Microsoft ®
Windows
■ Uninstalling the USB driver ............................. 16
D Microsoft ® Windows
D Microsoft ®
Windows
®
8.1 .................................. 9
® 7 ................................... 12
® 8.1 ............................. 14
®
7 ................................ 15
® 8.1 ............................. 16
®
7 ................................ 17
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
6 INSTALLING THE UTILITY SOFTWARE.... 18-20
■ Installing .......................................................... 18
■ Uninstalling the Utility software ....................... 20
7 REPEATER SETTINGS ............................... 21-26
■ ID-RP2C setting .............................................. 21
D ID-RP2C utility screen ................................. 22
■ Frequency setting for ID-RP2D ....................... 25
■ Frequency setting for ID-RP2V ....................... 26
8 MAINTENANCE ........................................... 27-28
■ Troubleshooting .............................................. 27
■ Cleaning .......................................................... 28
■ Replacing fuses .............................................. 28
D OPC-1309 ................................................... 28
D OPC-1380 ................................................... 28
9 SPECIFICATIONS AND OPTIONS ............. 29-30
■ Specifications .................................................. 29
D ID-RP2C ...................................................... 29
D ID-RP2D/ID-RP2V ....................................... 30
■ Options ........................................................... 30
10 INFORMATION ................................................. 31
■ About CE and DOC......................................... 31
■ Disposal .......................................................... 31
■ Country code list ............................................. 31
ii