Daikin MicroTech I Installation And Maintenance Manual page 37

Figure 30 continued: ATV 212 (MD2) Drive Parameters
PART NUMBER
170632000
Code Function Description
F471 VIA gain
F472 VIB bias
F473 VIB gain
F480 Exciting strengthening coefficient
F481 Factory adjustment 1
F482 Factory adjustment2
F483 Factory adjustment3
F485 Stall cooperation gain at field weakening zone 1
F492 Stall cooperation gain at field weakening zone 2
F494 Motor adjustment factor
F495 Maximum voltage adjustment factor
F496 Carrier change adjustment factor
F500 Acceleration time 2
F501 Deceleration time 2
F502 Acceleration/deceleration 1 pattern
F503 Acceleration/deceleration 2 pattern
F504 Acceleration/deceleration selection (1/2/3)
F505 Acceleration/deceleration 1 and 2 switching frequency
F506 S-pattern lower-limit adjustment amount
F507 S-pattern upper-limit adjustment amount
F601 Stall prevention level 1
F602 Inverter trip retention selection
F603 Emergency stop selection
F604 Emergency DC braking time
F605 Output phase failure detection mode selection
F607 Motor 150%-overload time limit
F608 Input phase failure detection mode selection
F609 Hysteresis for small current detection
F610 Low current trip/alarm
F611 Small current detection current
F612 Small current detection time
F613 Detection of output short-circuit during start-up
F615 Over-torque trip/alarm selection
F616 Over-torque detection level
F618 Over-torque detection time
F619 Over-torque detection level hysteresis
F621 Cumulative operation time alarm setting
F626 Over-voltage stall protection level
F627 Under-voltage trip/alarm selection
F632 Thermal memory selection
F633 Trip at VIA low level input mode
F634 Annual avg ambient temp (calculation for life alarms)
F645 Selection of PTC thermal
F646 Detection level of PTC
F650 Rorced/Fire-speed control selection
F691 Inclination characteristic of analog output
F692 Meter bias
F700 Prohibition of change of parameter settings
F701 Unit selection
F702 Free unit selection
F705 Inclination characteristic of free unit display
IM 1285-4 • MICROTECH III
REV
B Rooftop - MT3 SAF (set 321) PARAMETERS
Drive Voltage
ATV21 ALL
Unit Min. Value Max. Value
1 0 255
1 0 255
1 0 255
1% 100 130
1 0 9999
1 0 9999
0.1 0,0 300,0
1 10 250
1 50 150
1 0 200
1% 90 120
0.1kHz 0,1 14,0
0.1sec 0,0 3200,0
0.1sec 0,0 3200,0
1 0 2
1 0 2
1 1 2
0.01Hz 0,00 60,00
1% 0 50
1% 0 50
1% 10 111
1 0 1
1 0 2
0.1sec 0,0 20,0
1 0 5
1sec 10 2400
1 0 1
1% 1 20
1 0 1
1% 0 100
1sec 0 255
1 0 3
1 0 1
1% 0 250
0.1sec 0,0 10,0
1% 0 100
0.1 0,0 999,9
1% 100 150
1 0 2
1 0 1
1% 0 100
1 1 6
1 0 2
1ohm 100 9999
1 0 1
1 0 1
1% 0 100
1 0 1
1 0 1
0.01 0,00 200,00
1 0 1
37
PART DESCRIPTION
HP Application
ALL SAF/RAF, RT/SC
Default
New Value
Value
148
128
148
100
0
442
100
100
100
70
104
14
20
20
0
0
1
0
10
10
110
0
0
1
3 5
300
1
10
0
0
0
0
0
130
0.5
10
610
140
0
0
0
3
0
3000
0
1
0
0
1
0
1
ATV21 MT3 SAF PAGE 3
www.DaikinApplied.com
Appendix
Logical
Address
471
472
473
480
481
482
483
485
492
494
495
496
500
501
502
503
504
505
506
507
601
602
603
604
605
607
608
609
610
611
612
613
615
616
618
619
621
626
627
632
633
634
645
646
650
691
692
700
701
702
705