Table of Contents
Advertisement
Menu
Menu
Level 1
Level 2
8.1 T1S H.A. H
8 Holiday
For Serviceman
Setting
8.2 T5S H.A. DHW
10 Restore
10, 1 Restore Factory
For Serviceman
Factory Settings
Settings
11.1 Test Run Enable
11.2 Trail run steps
For Serviceman
11 Test Run
11.3 Point Check
14 Power Input
For Serviceman
14.1 POWER LIMITATION
Limitation
15.1 On/Off(M1M2)
15.2 Smart Grid
15.3 T1B(Tw2)
15.4 Tbt1
15.5 Tbt2
For Serviceman 15 Input Define
15.7 Solar Input
15.8 F-Pipe Length
15.10 Rt/Ta_Pcb
17.1 Program fw
17 FW Update
For Serviceman
USB
17.2 Verify Download --%
NOTE
* It allows you to enable or disable the functions that can be restarted in the event of a power failure.
62
EN
Menu
Menu
Level 3
Level 4
3way-valve 1
3way-valve 2
PUMPS
PUMP
PUMPC
PUMPSOLAR
PUMPDHW
INNER BACKUP HEATER
TANK HEATER
3WAY-VALVE 3
SOLAR ENABLE
IN SOLAR
/
/
Cod. 3542B230 - Rev. 00 - 02/2022
OMNIA S HYBRID H 3.2
Description
The target water output temperature for heating
the room in holiday mode
DHW water heater temperature set point in
holiday mode
Restore Factory Settings
TEST RUN ENABLE 0 = OFF 1 = ON - to enable
the menu "11.2 Trail run steps"
Point Check = to activate the menu "11.3 Point Check"
Air purge = ON - to activate the air bleed
Water pump = ON - to activate the water pump
Cooling = ON - to activate the cooling mode
Heating = ON -to activate the heating mode
Dhw = ON - to activate the DHW mode
TEST ON-OFF
Allows you to run a functional test on single loads, individually
forcing the activation and subsequent switching off.
Also allows you to temporarily force the system in specific
function modes for the test (air bleed, recirculation pump
running, etc.).
The switching on/off of each function is always done
manually.
It is only possible to enable/disable one function at a time; it is
not allowed at the same time.
If one function is active and you exit the Test Run menu while
it is active, the function will automatically switch off.
To limit the power absorbed by the heat pump
(refer to "Table 11 - Max current input (A) for
different level of power input limitation" on page
63.
Reserved
Enables or disables SMART GRID
Enables or disables temperature probe T1B
(Tw2)
Enables or disables temperature probe Tbt1
Reserved
Enables solar input
Type of solar input;
Tsolar (to enable the Tsolar solar panel probe
temperature);
SL1SL2 = do not use
Reserved
Reserved
/
BMS address setting of the heat pump
Unit of
Lower
Upper
Remedy
measure-
limit
limit
ment
20
25
1
°C
20
25
1
°C
Y
N
/
/
OFF
ON
/
/
Point Check / Air purge / Water pump / Cooling
/ Heating / Dhw
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
OFF
ON
/
/
0
8
1
/
Yes
No
/
/
Yes
No
/
/
Yes
No
/
/
Yes
No
/
/
-
-
/
/
Yes
No
/
/
Tsolar
SL1SL2
/
/
Yes
No
/
/
Yes
No
/
/
/
/
/
/
1
16
1
/
Default
value
25
25
N
OFF
Point
Check
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
0
No
No
No
No
No
No
SL1SL2
No
No
/
0
Advertisement
Table of Contents
