progressive automations FLT-09 Manual
  1. Manuals
  2. Brands
  3. progressive automations Manuals
  4. Indoor Furnishing
  5. FLT-09
  6. Manual

progressive automations FLT-09 Manual

Hide thumbs Also See for FLT-09:
Table of Contents

Advertisement

Quick Links

Download this manual
FLT-09
TABLE LIFT SET - 3 LEG - 3 STEP - STROKE SIZE 25.5
The FLT-09 is a three leg table lift set with a 25.5" stroke size and 110 lbs of force per leg.
This model comes with a power supply and an interactive remote with up to four
programmable preset functions. It comes with everything needed for installation. Table top
is not included.
HOW TO ORDER
1.800.676.6123
|
sales@progressiveautomations.com
|
www.progressiveautomations.com
Page 1 of 7

Advertisement

Table of Contents
loading

Related Manuals for progressive automations FLT-09

Summary of Contents for progressive automations FLT-09

  • Page 1 TABLE LIFT SET - 3 LEG - 3 STEP - STROKE SIZE 25.5 The FLT-09 is a three leg table lift set with a 25.5” stroke size and 110 lbs of force per leg. This model comes with a power supply and an interactive remote with up to four programmable preset functions.
  • Page 2 CAUTION/INFORMATION USE/LIABILITY Page 2 of 7 HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...
  • Page 3 PARTS Page 3 of 7 HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...
  • Page 4 ASSEMBLY INSTRUCTIONS STEP 1 STEP 3 Attach the 120° Frames (7,8) to one of the Legs (3) as Slide the Side Brackets (4) into both Frames (5). Attach the shown in the picture below. Line up the holes on the Leg brackets using four M6x14 Machine Screws (9).
  • Page 5 ASSEMBLY INSTRUCTIONS STEP 5 Attach each Foot (2) to the two end Legs (3) with four M6x14 Machine Screws and tighten them. Attach a Glide (1) to each foot and the middle Leg. Page 5 of 7 HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...

  • Page 6: Dimensional Drawing

    DIMENSIONAL DRAWING 49" 75.3" 23.5" 43.4" 22.6" 2" 1.2" 27.5" HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...

  • Page 7: Reset Procedure

    RESET PROCEDURE IMPORTANT You must reset the desk prior to use: To reset you must push and hold the DOWN button on the Hand Remote (7) until the table lift reaches its lowest point. Release the DOWN button. Press and hold the DOWN button again until the LED display shows "RST".

  • Page 8: Troubleshooting

    TROUBLESHOOTING If your table lift is not functioning it might need to be reset. Follow the RESET procedure from page 6. If your hand remote has an LED display and it displays "RST" (reset), perform the reset procedure from page 6. If the LED displays shows an error message ("Er1"...
  • Page 9 SETTING UPPER & LOWER LIMITS Upper Limit To set the upper limit, use the UP/DOWN buttons to move the table lift to your desired max height position. Once it is at the desired position, press and hold the "M" until the LED display flashes "S-"...
  • Page 10 MODIFIYING LED DISPLAY Press the DOWN button on the Hand Remote until the base reaches its lowest position. Measure the height of the base from the floor and if the number on the LED display does not match your measurements, follow the steps below: Press and hold the DOWN button again until the LED display reads "RST".

Table of Contents