Download
Share
Print this page
  1. Manuals
  2. Brands
  3. progressive automations Manuals
  4. Indoor Furnishing
  5. flt-02
  6. Manual

progressive automations FLT-02 Manual

Table lift set - dual - 3 step - stroke size 25.5
Hide thumbs Also See for FLT-02:

Advertisement

Quick Links

Download this manual See also: User Manual
FLT-02 Manual
TABLE LIFT SET - DUAL - 3 STEP - STROKE SIZE 25.5
The FLT-02 is a dual leg table lift set with a 25.5" stroke size and 180 lbs of force. This
model comes with a power supply and an interactive remote with four programmable
preset functions. It comes with everything needed for installation. Table top is not included.
Page 1 of 7
HOW TO ORDER
1.800.676.6123
|
|
sales@progressiveautomations.com
www.progressiveautomations.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the FLT-02 and is the answer not in the manual?

Questions and answers

Related Manuals for progressive automations FLT-02

Summary of Contents for progressive automations FLT-02

  • Page 1 TABLE LIFT SET - DUAL - 3 STEP - STROKE SIZE 25.5 The FLT-02 is a dual leg table lift set with a 25.5” stroke size and 180 lbs of force. This model comes with a power supply and an interactive remote with four programmable preset functions.
  • Page 2 CAUTION/INFORMATION USE/LIABILITY Page 2 of 7 HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...
  • Page 3 PARTS Page 3 of 7 HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...
  • Page 4 ASSEMBLY INSTRUCTIONS STEP 1 Before you start make sure to lay out all the components and hardware to ensure you have all the necessary parts listed on the parts page. Separate the Frame Ends (3a,3b) and you will find the Center Rails (4) inside. STEP 2 Place one of the Legs (1) into the Frame End-CB (3a) making STEP 4...
  • Page 5 ASSEMBLY INSTRUCTIONS STEP 8 STEP 6 Make sure that the wood screws are not too long for your Depending on your desktop, it may or may not be pre- desktop, otherwise they will puncture the surface once drilled. Make sure to check both sides of the desktop screwed all the way in.
  • Page 6 ASSEMBLY INSTRUCTIONS IMPORTANT STEP 9 You must reset the desk prior to use: Connect the cable from the Leg (1) that is attached to the To reset you must push and hold the DOWN button on the Frame End-CB (3a) directly into the Control Box (6). Then Hand Remote (7) until the table lift reaches its lowest Slide the Control Box (6) into the Frame End-CB (3a).

  • Page 7: Dimensional Drawing

    DIMENSIONAL DRAWING 22.6" 49" 2" 27.5" 72.4" 43" 0.3" 17.7" 8.2" 10" 10" HOW TO ORDER 1.800.676.6123 sales@progressiveautomations.com www.progressiveautomations.com...

  • Page 8: Troubleshooting

    TROUBLESHOOTING If your desk is not functioning it might need to be reset. Follow the RESET procedure from page 6. If your hand remote has an LED display and it displays "RST" (reset), perform the reset procedure from page 6. If the LED displays shows an error message ("Er1"...
  • Page 9 SETTING UPPER & LOWER LIMITS Upper Limit To set the upper limit, use the UP/DOWN buttons to move the table lift to your desired max height position. Once it is at the desired position, press and hold the "M" until the LED display flashes "S-"...
  • Page 10 MODIFIYING LED DISPLAY Press the DOWN button on the Hand Remote until the base reaches its lowest position. Measure the height of the base from the floor and if the number on the LED display does not match your measurements, follow the steps below: Press and hold the DOWN button again until the LED display reads "RST".