Analog Devices ADSP-BF537 EZ-KIT Lite Manual
  1. Manuals
  2. Brands
  3. Analog Devices Manuals
  4. Computer Hardware
  5. EZ-KIT Lite ADSP-BF537
  6. Manual
Analog Devices ADSP-BF537 EZ-KIT Lite Manual

Analog Devices ADSP-BF537 EZ-KIT Lite Manual

Evaluation system
Hide thumbs Also See for ADSP-BF537 EZ-KIT Lite:
Table of Contents

Advertisement

Quick Links

Download this manual
ADSP-BF537 EZ-KIT Lite
®
Evaluation System Manual
Revision 2.5, July 2012
Part Number
82-000865-01
Analog Devices, Inc.
One Technology Way
a
Norwood, Mass. 02062-9106

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADSP-BF537 EZ-KIT Lite and is the answer not in the manual?

Questions and answers

Related Manuals for Analog Devices ADSP-BF537 EZ-KIT Lite

Summary of Contents for Analog Devices ADSP-BF537 EZ-KIT Lite

  • Page 1 ADSP-BF537 EZ-KIT Lite ® Evaluation System Manual Revision 2.5, July 2012 Part Number 82-000865-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106...
  • Page 2 Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use;...
  • Page 3 Regulatory Compliance The ADSP-BF537 EZ-KIT Lite is designed to be used solely in a labora- tory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity.

  • Page 5: Table Of Contents

    EngineerZone ................ xvii Related Documents ..............xviii Notation Conventions ..............xviii USING THE ADSP-BF537 EZ-KIT LITE Package Contents ................1-3 Default Configuration ..............1-3 CCES Install and Session Startup ..........1-4 Session Startup ................ 1-6 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 6 System Architecture ..............2-2 External Bus Interface Unit ............. 2-3 SPORT0 Audio Interface ............2-4 SPI Interface ................2-4 Programmable Flags (PFs) ............2-4 UART Port ................2-7 Expansion Interface ..............2-7 JTAG Emulation Port ............. 2-8 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 7 Reset Push Button (SW9) ............2-18 Programmable Flag Push Buttons (SW10–13) ......2-19 Power LED (LED7) ............... 2-19 Reset LED (LED8) ..............2-19 User LEDs (LED1–6) ............2-20 USB Monitor LED (ZLED3) ..........2-20 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 8 PPI Connector (P8) .............. 2-25 SPI Connector (P9) ............... 2-26 2-Wire Interface Connector (P10) ......... 2-26 TIMERS Connector (P11) ............ 2-26 UART1 Connector (P12) ............2-27 ADSP-BF537 EZ-KIT LITE BILL OF MATERIALS ADSP-BF537 EZ-KIT LITE SCHEMATIC INDEX viii ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 9 PREFACE ® Thank you for purchasing the ADSP-BF537 EZ-KIT Lite , Analog ® Devices, Inc. evaluation system for Blackfin processors. Blackfin processors embody a type of embedded processor designed specif- ically to meet the computational demands and power constraints of today’s embedded audio, video, and communications applications.
  • Page 10 ADSP-BF537 processor and the evaluation board peripherals. Analog Devices JTAG emulators offer faster communication between the host PC and target hardware. Analog Devices carries a wide range of in-circuit emulation products. To learn more about Analog Devices emulators and processor development tools, go to http://www.analog.com/dsp/tools...

  • Page 11: Preface

    • AD1854 96 kHz digital-to-audio codec (DAC) • 1 input stereo jack • 1 output stereo jack • Ethernet interface • 10-BaseT (10M bits/sec) and 100-BaseT (100M bits/sec) Ethernet Media Access Controller (MAC) • SMSC LAN83C185 device ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 12 6 general-purpose (amber), and 1 USB monitor (amber) • Push buttons • 5 push buttons: 1 reset, 4 programmable flags with debounce logic • Expansion interface • All processor signals • Other features • JTAG ICE 14-pin header ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 13: Purpose Of This Manual

    VisualDSP++ users should use this manual in conjunction with the Get- ting Started with ADSP-BF537 EZ-KIT Lite, which familiarizes users with the hardware capabilities of the evaluation system and demonstrates how to access these capabilities in the VisualDSP++ environment.

  • Page 14: Intended Audience

    Intended Audience Intended Audience The primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture and instruction set. Programmers who are unfamiliar with Analog Devices processors can use this manual but should supplement it with other texts that describe your target architecture.

  • Page 15: What's New In This Manual

    Manual. The manual has been updated to include CCES information. In addition, modifications and corrections based on errata reports against the previous manual revision have been made. For the latest version of this manual, please refer to the Analog Devices Web site. Technical Support...

  • Page 16: Supported Processors

    Supported Processors This evaluation system supports Analog Devices ADSP-BF537 Blackfin embedded processors. Product Information Product information can be obtained from the Analog Devices Web site and the online help system. Analog Devices Web Site The Analog Devices Web site, , provides information www.analog.com...

  • Page 17: Engineerzone

    Also note, is a free feature of the Analog Devices Web site that myAnalog allows customization of a Web page to display only the latest information about products you are interested in.

  • Page 18: Related Documents

    . One or the other is required. that Optional items in syntax descriptions appear within brackets and sepa- [this | that] rated by vertical bars; read the example as an optional this that xviii ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 19 A Warning identifies conditions or inappropriate usage of the product that could lead to conditions that are potentially hazardous for the devices users. In the online version of this book, the word Warning appears instead of this symbol. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 20 Notation Conventions ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 21: Using The Adsp-Bf537 Ez-Kit Lite

    1 USING THE ADSP-BF537 EZ-KIT LITE This chapter provides specific information to assist you with development of programs for the ADSP-BF537 EZ-KIT Lite evaluation system. The information appears in the following sections. • “Package Contents” on page 1-3 Lists the items contained in your ADSP-BF537 EZ-KIT Lite package.
  • Page 22 EZ-KIT Lite system, refer to the online help. For more detailed information about programming the ADSP-BF537 Blackfin processor, see the documents referred to as “Related Documents”. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 23: Package Contents

    Store unused EZ-KIT Lite boards in the protective shipping package. The ADSP-BF537 EZ-KIT Lite board is designed to run outside your per- sonal computer as a standalone unit. When removing the EZ-KIT Lite board from the package, handle the...

  • Page 24: Cces Install And Session Startup

    Figure 1-1. EZ-KIT Lite Hardware Setup CCES Install and Session Startup For information about CCES and to download the software, go to . A link for the ADSP-BF537 EZ-KIT Lite Board www.analog.com/CCES Support Package (BSP) for CCES can be found at http://www.analog.com/Blackfin/EZKits...
  • Page 25 Using the ADSP-BF537 EZ-KIT Lite Step 1: Connect the EZ-KIT Lite board to a personal computer (PC) run- ning CCES using one of two options: an Analog Devices emulator or via the debug agent. Using an Emulator: 1. Plug one side of the USB cable into the USB connector of the emu- lator.

  • Page 26: Session Startup

    Debug Configurations • Choose Run > Debug Configurations. The Debug Configuration dialog box appears. 3. Select CrossCore Embedded Studio Application and click (New launch configuration). The Select Processor page of the Session Wizard appears. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 27 The Select Platform page of the Session Wizard appears. 6. Do one of the following: • For standalone debug agent connections, ensure that the selected platform is ADSP-BF537 EZ-KIT Lite via Debug Agent. • For emulator connections, choose the type of emulator that is connected to the board.

  • Page 28: Visualdsp++ Install And Session Startup

    VisualDSP++ to start a new session by pressing and holding down the Ctrl key while starting VisualDSP++. Do not release the Ctrl key until the Session Wizard appears on the screen. Go to step 4. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 29 Select EZ-KIT Lite and click Next. 6. The Select Platform page of the wizard appears on the screen. In the Select your platform list, select ADSP-BF537 EZ-KIT Lite via Debug Agent. In Session name, highlight or specify the session name.

  • Page 30: Cces Evaluation License

    Delete. Click OK. CCES Evaluation License The ADSP-BF537 EZ-KIT Lite software is part of the Board Support Package (BSP) for the Blackfin ADSP-BF53x family. The EZ-KIT Lite is a licensed product that offers an unrestricted evaluation license for 90 days after activation.

  • Page 31: Visualdsp++ Evaluation License

    CCES with a valid evaluation or full license. VisualDSP++ Evaluation License The ADSP-BF537 EZ-KIT Lite installation is part of the VisualDSP++ installation. The EZ-KIT Lite is a licensed product that offers an unre- stricted evaluation license for the first 90 days. Once the initial unrestricted 90-day evaluation license expires: •...
  • Page 32 0xFFA0 8000 0xFFA0 BFFF Scratch pad SRAM 4 KB 0xFFB0 0000 0xFFB0 0FFF System MMRs 2 MB 0xFFC0 0000 0xFFDF FFFF Core MMRs 2 MB 0xFFE0 0000 0xFFFF FFFF All other locations Reserved 1-12 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 33: Sdram Interface

    Bank 0 size = 64 MB Bank 0 column address width = 10 bits Calculated with = 54 MHz EBIU_SDRRC 0x000003A0 SCLK = 416 clock cycles RDIV 1 54 MHz <=SCLK <= 133 MHz. ADSP-BF537 EZ-KIT Lite Evaluation System Manual 1-13...
  • Page 34 (CCLK = 600 MHz) EBIU_SDGCTL 0x0091 998D 0x0091 998D EBIU_SDBCTL 0x0000 0025 0x0000 0025 EBIU_SDRRC 0x0000 0408 0x0000 03A0 An example program is included in the EZ-KIT Lite installation directory to demonstrate the SDRAM memory setup. 1-14 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 35: Flash Memory

    Using the ADSP-BF537 EZ-KIT Lite Flash Memory The flash memory interface of the ADSP-BF537 EZ-KIT Lite contains a 4 MB (2M x 16-bits) ST Micro M29W320EB device. The size of flash memory is controlled by the flash address range switch, .

  • Page 36: Ethernet Interface

    , is a RJ-45 type connector with built-in mag- netics and LEDs (see “Ethernet Connector (J4)” on page 2-22). Example programs are included in the EZ-KIT Lite installation directory to demonstrate Ethernet circuit operation. 1-16 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 37: Elvis Interface

    (DAC). The audio circuit provides one channel of stereo input and one channel of stereo output via 3.5 mm stereo jacks. The SPORT0 interface of the processor is linked with the stereo audio data input and output pins of the audio circuit. ADSP-BF537 EZ-KIT Lite Evaluation System Manual 1-17...

  • Page 38: Leds And Push Buttons

    PF input is established through the DIP switch. See “LEDs and Push Buttons” on page 2-18 for details. An example program is included in the EZ-KIT Lite installation directory to demonstrate functionality of the LEDs and push buttons. 1-18 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 39: Board Design Database

    Analog Devices board design database at: http://www.analog.com/board-design-database Example Programs Example programs are provided with the ADSP-BF537 EZ-KIT Lite to demonstrate various capabilities of the product. The programs are included in the product installation kit and can be found in the Examples folder of the installation.
  • Page 40 Example Programs 1-20 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 41: Adsp-Bf537 Ez-Kit Lite Hardware Reference

    This chapter describes the hardware design of the ADSP-BF537 EZ-KIT Lite board. The following topics are covered. • “System Architecture” on page 2-2 Describes the ADSP-BF537 EZ-KIT Lite configuration and explains how the board components interface with the processor. • “Jumper and Switch Settings” on page 2-9 Shows the locations and describes the configuration jumpers and switches.

  • Page 42: System Architecture

    This EZ-KIT Lite is designed to demonstrate the capabilities of the ADSP-BF537 Blackfin processor. The processor has an IO voltage of 3.3V. The core voltage of the processor is supplied by the internal voltage regulator. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 43: External Bus Interface Unit

    All of the address, data, and control signals are available externally via the expansion interface ( ). The pinout of these connectors can be found J1–3 “ADSP-BF537 EZ-KIT Lite Schematic” on page B-1. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 44: Sport0 Audio Interface

    The pinout of the and expansion interface connectors can be found SPORT “ADSP-BF537 EZ-KIT Lite Schematic” on page B-1. SPI Interface The serial peripheral interface (SPI) of the processor connects to the SPI connector ( ) and the expansion interface.
  • Page 45 LED6 on page 1-18 for information on how to dis- able the push button. Audio reset PF12 SPI_MISO PF13 SPI_SCK PF14 SPI_SS/TACLK0 PF15 PPI4_CLK/TMRCLK PPI_D0 ELVIS_TRIGGER PPI_D1 ELVIS_PF1 PPI_D2 ELVIS_PF2 PPI_D3 ELVIS_PF5 PPI_D4 ELVIS_PF6 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 46 Ethernet interface ERXD1 ERXD1 used for Ethernet interface PH10 ERXD2 ERXD2 used for Ethernet interface PH11 ERXD3 ERXD3 used for Ethernet interface PH12 ERXDV/TACLK5 ERXDV used for Ethernet interface PH13 ERXCLK/TACLK6 ERXCLK ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 47: Uart Port

    The mechanical dimensions of the connectors can be obtained from Tech- nical Support. Analog Devices offers many EZ-Extender products that plug on to the expansion interface. For more information on these products, visit the Analog Devices Web site at http://www.analog.com/processors/tools/blackfin Table 2-2.

  • Page 48: Jtag Emulation Port

     Analog Devices does not support and is not responsible for the effects of additional circuitry. JTAG Emulation Port The JTAG emulation port allows an emulator to access the processor’s internal and external memory through a 6-pin interface.

  • Page 49: Jumper And Switch Settings

    The Controller Area Network (CAN) enable switch ( ) disconnects the CAN signals from the GPIO pins of the processor. When the switch is in the position, its associated GPIO signal (see Table 2-3) can be used on the expansion interface. ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 50: Ethernet Mode Select Switch (Sw3)

    10Base-T half duplex; auto-negotiation disabled 10Base-T full duplex; auto-negotiation disabled 100Base-T half duplex; auto-negotiation disabled 100Base-T full duplex; auto-negotiation disabled 100Base-T half duplex; auto-negotiation enabled Repeater mode; auto-negotiation enabled Power down mode All capable; auto-negotiation enabled (default) 2-10 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 51: Uart Enable Switch (Sw4)

    GPIO signal (see Table 2-6) can be used on the expansion interface. Table 2-6. Push Button Enable Switch (SW5) Push Button SW5 Switch Position (Default) Processor Signal SW13 SW12 SW11 SW10 ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-11...

  • Page 52: Flash Enable Switch (Sw6)

    Positions 6 and 7 connect the transmit and receive clocks together (see Table 2-8). Table 2-8. Audio Enable Switch (SW7) EZ-KIT Lite Signal SW7 Switch Position (Default) Processor Signal DR0PRI RSCLK0 RFS0 TSCLK0 TFS0 PJ10 2-12 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 53: Boot Mode Select Switch (Sw16)

    The 3V power selection jumper ( ) selects the power source for the 3-volt parts. In a standard mode of operation, the parts are powered by the on-board switching regulator circuit via an external power supply. When a ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-13...

  • Page 54: Expansion Interface Voltage Selection Jumper (Jp5)

    2-11. Table 2-11. Expansion Interface Voltage Selection Jumper (JP5) JP5 Setting Mode 5V signal powered from the on-board switching regulator (default) 5V signal powered from an external power supply: USB-bus power or Power-over-Ethernet 2-14 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 55: Uart Loop Jumper (Jp9)

    1-17). Each channel must have only one signal selected at a time (see Table 2-12). Table 2-12. Oscilloscope Configuration Switch (SW1) Channel SW1 Switch Position (Default) Audio Circuit Signal OFF) AMP_LEFT_IN AMP_RIGHT_IN LEFT_OUT RIGHT_OUT AMP_LEFT_IN AMP_RIGHT_IN LEFT_OUT RIGHT_OUT ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-15...

  • Page 56: Elvis Function Generator Configuration Switch (Sw8)

    When is installed, the board is powered from an ELVIS station, and no external power sup- ply is required. The jumper setting is shown in Table 2-14. 2-16 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 57: Elvis Select Jumper (Jp8)

    ELVIS station, instead of the processor. The jumper setting is shown Table 2-15. Table 2-15. ELVIS Select Jumper (JP8) JP8 Setting Mode Not connected to an ELVIS station (default) Connected to an ELVIS station ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-17...

  • Page 58: Leds And Push Buttons

    USB cable has been plugged in and communication with the PC has been initialized correctly. After USB communication has been initialized, the only way to reset the USB chip is by powering down the board. 2-18 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 59: Programmable Flag Push Buttons (Sw10-13)

    (green), it indicates that power is being properly supplied LED7 to the board. Reset LED (LED8) When is lit, it indicates that a master reset of all the major ICs is LED8 active. ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-19...

  • Page 60: User Leds (Led1-6)

    15 seconds. If the LED does not light, try cycling power on the board and/or re-installing the USB driver.  When CCES or VisualDSP++ is actively communicating with the EZ-KIT Lite target board, the LED can flicker, indicating commu- nications handshake. 2-20 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 61: Connectors

    ADSP-BF537 EZ-KIT Lite Hardware Reference Connectors This section describes the connector functionality and provides informa- tion about mating connectors. The connector locations are shown in Figure 2-4. Figure 2-4. Connector Locations ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-21...

  • Page 62: Audio Connectors (J9 And J10)

    4-conductor modular jack cable L-COM TSP3044 Ethernet Connector (J4) Part Description Manufacturer Part Number Ethernet jack PULSE JK0-0025NL Mating Cable (shipped with EZ-KIT Lite) Cat 5E patch cable RANDOM PC10/100T-007 Cat 5E crossover cable RANDOM PC10/100TC-007 2-22 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 63: Power Connector (J7)

    The power connector provides all of the power necessary to operate the EZ-KIT Lite board. Part Description Manufacturer Part Number 2.5 mm power jack SWITCHCRAFT RAPC712X Mating Power Supply (shipped with EZ-KIT Lite) 7V power supply CUI INC. DMS070214-P6P-SZ ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-23...

  • Page 64: Expansion Interface Connectors (J1-3)

    Pin 3 is missing to provide keying. Pin 3 in the mating connector should have a plug.  When using an emulator with the EZ-KIT Lite board, follow the connection instructions provided with the emulator. 2-24 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 65: Sport0 Connector (P6)

    PPI Connector (P8) The pinout of the connector can be found in “ADSP-BF537 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-440HLF Mating Connector IDC socket DIGI-KEY S4220-ND ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-25...

  • Page 66: Spi Connector (P9)

    TIMERS Connector (P11) The pinout of the connector can be found in “ADSP-BF537 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-410HLF Mating Connector IDC socket DIGI-KEY S4205-ND 2-26 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 67: Uart1 Connector (P12)

    UART1 Connector (P12) The pinout of the connector can be found in “ADSP-BF537 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-410HLF Mating Connector IDC socket DIGI-KEY S4205-ND ADSP-BF537 EZ-KIT Lite Evaluation System Manual 2-27...
  • Page 68 Connectors 2-28 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 69 OSC005 25.0000M-C0:ROHS SN74AHC1G00 SN74AHC1G00DBVR SOT23-5 12.288MHZ DIGI-KEY SG-8002CA-PCC-ND OSC003 (12.288M) 32.768KHZ EPSON MC-156-32.7680KA-A0: OSC008 ROHS SN74LVC1G32 SN74LVC1G32DBVRE4 SOT23-5 25MHZ U51,U53 DIGI-KEY SG-8002CA-PCC-ND OSC003 (25.00M) SN74LVC1G08 U22,U47-50, SN74LVC1G08DBVR SOT23-5 MT48LC32M8A U15-16 MICRON MT48LC32M8A2P-75 2 TSOP54 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 70 ANALOG AD1854JRSZ SSOP28 DEVICES AD1871YRSZ ANALOG AD1871YRSZ SSOP28 DEVICES ADM3202ARN ANALOG ADM3202ARNZ Z SOIC16 DEVICES AD623ARMZ U2-3 ANALOG AD623ARMZ USOIC8 DEVICES AD820ARZ U11,U23 ANALOG AD820ARZ SOIC8 DEVICES ADG774ABRQ U54-57 ANALOG ADG774ABRQZ Z QSOP16 DEVICES ADSP-BF537 EZ-KIT Lite Evaluation System Manual...

  • Page 71: Adsp-Bf537 Ez-Kit Lite Bill Of Materials

    ADSP-BF537 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Manufacturer Part Number Designator ADSP-BF537 ANALOG ADSP-BF537KBCZ-6A MINI_BGA182 DEVICES RUBBER FOOT M1-5 MOUSER 517-SJ-5018BK SWITCH- RAPC712X 2.5MM_JACK CRAFT CON005 MOMENTARY SW9-13 PANASONIC EVQ-PAD04M SWT013 .05 45X2 J1-3 SAMTEC SFC-145-T2-F-D-A CON019...
  • Page 72 10UF 16V10% CT7-8 TAJC106K016R 100 1/10W 5% R82,R100-101, VISHAY CRCW0805100RJNEA 0805 R103 600 100MHZ FER1-5,FER9 DIGI-KEY 490-1014-2-ND 200MA 0603 2A S2A VISHAY S2A-E3 DO-214AA 68UF 6.3V20% TAJD686K016R 68UF 25V 20% CT1-2 PANASONIC EEE-FC1E680P CAP003 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 73 ADSP-BF537 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Manufacturer Part Number Designator 10UH 20% 445-2014-1-ND IND001 190 100MHZ FER7 MURATA DLW5BSN191SQ2 5A FER002 1A ZHCS1000 ZETEX ZHCS1000TA pb-free SOT23D 1UF 10V 10% C131,C134, 0805ZC105KAT2A 0805 C210,C220-222 10UF 6.3V 10%...
  • Page 74 5% 0805 0.1UF 16V 10% C64,C72-74, 0603YC104KAT2A 0603 C87-89,C125, C130,C133 33PF 50V 5% C118,C122 PANASONIC ECJ-1VC1H330J 0603 0.01UF 16V C50-51,C62-63, 0603YC103KAT2A 10% 0603 4.7UF 25V 20% C110 0805ZD475KAT2A 0805 330PF 50V 5% C79,C84 06035A331JAT2A 0603 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 75 ADSP-BF537 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Manufacturer Part Number Designator 10K 1/10W 5% R37,R53,R99 VISHAY CRCW060310K0JNEA 0603 10M 1/10W 5% R10-11 VISHAY CRCW060310M0FNEA 0603 100K 1/10W 5% R20,R26 VISHAY CRCW0603100KJNEA 0603 330 1/10W 5% R75-76,R83, VISHAY...
  • Page 76 C52-54,C61, 06035A101JAT2A 0603 C65,C68,C75, C77,C81,C85, C94,C106 1000PF 50V 5% C66-67,C69-70 PANASONIC ECJ-1VC1H102J 0603 12.4K 1/10W DIGI-KEY 311-12.4KHRTR-ND 1% 0603 62.0 1/10W 1% R65-66 DIGI-KEY 311-62.0HRTR-ND 0603 220PF 50V 5% C82,C86,C117, PANASONIC ECJ-1VC1H221J 0603 C124 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 77 ADSP-BF537 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Manufacturer Part Number Designator 680PF 50V 5% C80,C83 PANASONIC ECJ-1VC1H681J 0603 2200PF 50V 5% C76,C78 PANASONIC ECJ-1VB1H222K 0603 2.74K 1/10W R36,R52 DIGI-KEY 311-2.74KHRTR-ND 1% 0603 100 1/16W 5% R213-214 DIGI-KEY...
  • Page 78 Ref. Qty. Description Reference Manufacturer Part Number Designator 150UF 6.3V CT4,CT6 PANASONIC EEFUE0J151R 10% D 30 100MHZ R217 DIGI-KEY 240-2362-1-ND 500MA 0402 A-10 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 80 RESET RESET ADSP-BF537 MINI_BGA182 XTAL CLKIN 3V_BP 0603 25MHZ OSC005 0402 0402 18PF 18PF 0805 0805 25MHZ OSC003 3V_BP RTXI RTXO 0603 R170 R171 R172 0402 0402 0402 PJ8_DR0PRI TERM1 TERM2 32.768KHZ PJ3_SDA 18PF 18PF OSC008 0805 0805 PJ4_CAN_RX PJ2_SCL ARDY...
  • Page 81 ABE1 MT48LC32M8A2 TSOP54 64 MB SDRAM (8M x 8 x 4 banks) x 2 chips 3V_BP 3V_BP 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0402 0402 0402 0402 0402 0402 0402...
  • Page 82 AGND 100K 100PF 0603 0603 AGND VREF_AUDIO FER2 0603 0603 C212 0.1UF 0.1UF 0.1UF 10UF 0402 0402 0402 0805 AGND AGND AGND LMV722 LMV722 AD1871...
  • Page 83 DEEMP 0603 MUTE IDPM0 IDPM1 AD1854 SSOP2 0.1UF 0.1UF 0.1UF 0603 0603 0603 AGND AD1854 AD1854 LMV722...
  • Page 84 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0402 0402 0402 0402 0402 0402 0402 0402 XTAL1_PHY R211 R212 63.4 0603 0402 25MHZ OSC005 C228 C224 27PF 27PF 0402 0402 3V_BP R208 0402 R209 0402 25MHZ OSC003 R210 0402 CLKBUF...
  • Page 85 0402 LABEL "PB4" 0805 0603 RS_P3 SW10 74LVC14A MOMENTARY SOIC14 SWT013 C210 0805 3V_BP DA_SO R162 0402 0402 74LVC14A 74LVC14A SOIC14 SOIC14 3V_BP C109 C107 C108 C211 C225 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0402 0402 0402 0402 0402 IDT74FCT3244 QS3257 QS3257 74LVC14A ADM708...
  • Page 86 90.9K 0603 VDDEXT_SHUNT VDDEXT R159 10.0K 0603 AD820ARZ SOIC8 AD623ARMZ C204 USOIC8 0.01UF 10.0K R148 0402 0603 0603 R104 25.5K 0603 0.1UF 0603 AGND DSP IO CURRENT...
  • Page 87 PF3_PB2 ABE1 ABE0 PG0_ELVIS_TRIGGER PF15_CAN_STB~ PG2_ELVIS_PF2 PG1_ELVIS_PF1 POE_VCC+ PG3_ELVIS_PF5 POE_VCC- PF7_LED2 ABE0 PF4_PB3 PF6_LED1 SRAS PF2_PB1 PF5_PB4 SA10 PF3_PB2 R168 0603 CON019...
  • Page 88 PF15_CAN_STB~ PG0_ELVIS_TRIGGER PG2_ELVIS_PF2 PG1_ELVIS_PF1 PG4_ELVIS_PF6 PG3_ELVIS_PF5 PG6_UART0_CTS PG5_ELVIS_PF7 PG7_UART0_RTS PG10 PG0_EL PG12 PG11 PG14 PG13 PF9_LED4 PG15_USB_IRQ PF14_CAN_EN PF10_LED5 RESET PF15_CAN_STB~ PF11_LED6 PF7_LED2 PF12_AUDIO_RESET PF9_LED4 PF13_CAN_ERR PF8_LED3 PJ3_SDA PJ2_SCL IDC20X2 3.3V TIMERS PF2_PB1 PF3_PB2 PF9_LED4 PF4_PB3 PF8_LED3 PF7_LED2 IDC5X2...
  • Page 89 MH10 MH11 MH12 MH13 MH14 LABEL "VDDINT" VDDINT_SHUNT TP10 3V_BP VROUT R115 10UH IND001 0603 R207 0402 68UF ZHCS1000 SOT23D FDS9431A SOIC8 C125 0.1UF 0603...
  • Page 90 See AD1854, AD1871 out (CLK OUT) signals, connectors (J9-10), 2-22 codecs, See AD1854, AD1871 enable switch (SW7), 2-12 COL signals, input configuration switch (SW8), 2-16 configuration, of this EZ-KIT Lite, interface, xiii, 1-17, ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 91 EBIU_SDRRC register, 1-13, 1-14 address range switch (SW6), 1-15 EBUI control signals, boot mode, 2-13 Educational Laboratory Virtual connections, 1-15, Instrumentation Suite interface, See enable (SW6) switch, 2-12 ELVIS frame sync signals, 1-18 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 92 JP3 (power), 2-13 JP5 (expansion voltage), 2-14 package contents, JP6 (ELVIS voltage), 2-16 PB1-4 (SW13-10) push buttons, 2-11 JP8 (ELVIS select), 2-17 PF1 signals, 2-11 JP9 (UART), 2-15 PG7-6 signals, 2-11 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 93 RIGHT_OUT signals, 2-15 CCES, RJ-45 connectors, 1-16 STB (standby control input) signals, 1-16, RMII_MDINT signals, 2-5, 2-10 RMII_REF_CLK signals, stereo input/output channels, 1-17 RS-232 connectors (J6), xiii, 2-23 SW10-13 (PF2-5) push buttons, 2-5, 2-19 ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 94 TACLK0 signals, voltage regulators, TACLK7-5 signals, technical support, TFS0 signals, 2-12 timers connector (P11), 2-26 TMR6-0 signals, TMRCLK signals, TSCLK0 signals, 2-12 TWI connector (P10), 2-26 TXD (transmit data input) signals, 1-16 TX signals, ADSP-BF537 EZ-KIT Lite Evaluation System Manual...
  • Page 95 Development Boards & Kits - Other Processors Click to view products by manufacturer: Analog Devices Other Similar products are found below : EVB-MEC1418MECC 20-101-1252 C29XPCIE-RDB CC-ACC-18M433 MAX1464EVKIT RTE510Y470TGB00000R RTK0EN0001D01001BZ MAXQ622-KIT# YR0K505231S000BE YR0K50571MS000BE YQB-R5F1057A-TB QB-R5F104PJ-TB CC- ACC-ETHMX OV-7604-C7-EVALUATION-BOARD SK-AD02-D62Q1747TB SK-BS01-D62Q1577TB ST7MDT1-EMU2 GROVE BASE...

Table of Contents