Pace PAI Installation And Assembly Manual page 8

PACE │ Installation & Assembly Manual
LIST OF FIGURES
FIGURE 1 - Cutaway Showing Segmented Construction .......................................................................................15
FIGURE 2 - AHU and Coil Hand Identification ........................................................................................................16
FIGURE 3 - AHU ID Label .......................................................................................................................................17
FIGURE 4 - Skid ID Label .......................................................................................................................................17
FIGURE 5 - Example of Segment ID Box................................................................................................................17
FIGURE 6 - Metal Spacers on Doors ......................................................................................................................21
FIGURE 7 - Recommended Lifting with Multiple Points ..........................................................................................22
FIGURE 8 - Typical Come-A-Longs ........................................................................................................................22
FIGURE 9 - Proper Lifting with Shackle with Corner Connector Corners ............................................................... 22
FIGURE 10 - Proper Lifting with Shackle at Lifting Lug...........................................................................................23
FIGURE 11 - Proper Lifting with Base Rail ..............................................................................................................23
FIGURE 12 - Minimum Service Clearances ............................................................................................................24
FIGURE 13 - Typical Curb Assembly ......................................................................................................................25
FIGURE 14 - No Base Rail - Housekeeping Pad Required to Accommodate Trap Height ..................................... 26
FIGURE 15 - No Housekeeping Pad - Base Rail Required to Accommodate Trap Height ..................................... 26
FIGURE 16 - With Base or Base Rail and Housekeeping Pad ...............................................................................26
FIGURE 17 - Ceiling Suspended AHU on Structural Steel......................................................................................27
FIGURE 18 - Tools Needed to Assemble Shipping Splits .......................................................................................28
FIGURE 19 - Shipping Split Examples ....................................................................................................................29
FIGURE 20 - Shipping Split Examples Using Structural Steel Baserails ................................................................ 30
FIGURE 21 - Applying Gasket Square, Neoprene Gasket and Caulk to Raceway Split ......................................... 30
FIGURE 22 - Typical Come-A-Longs ......................................................................................................................31
FIGURE 23 - Electrical Connector (Not Connected) ...............................................................................................31
FIGURE 24 - Electrical Connectors (Connected) ....................................................................................................31
FIGURE 25 - Remove and Reposition Shipping Split Angle ...................................................................................31
FIGURE 26 - Come-A-Long Attached to a Section .................................................................................................32
FIGURE 27 - Bring Shipping Splits Together ...........................................................................................................32
FIGURE 28 - Applying Caulk to Seams ...................................................................................................................32
FIGURE 29 - Installing Gaskets ..............................................................................................................................33
FIGURE 30 - Corner Connector Hole Plug (P/N 021-19568-000) ...........................................................................33
FIGURE 32 - Use Gasket (P/N 028-11883-010) at Shipping Split ..........................................................................34
FIGURE 31 - Installing Hood with Optional Moisture Eliminators............................................................................34
FIGURE 34 - Assembly of End Channel Shipping Split with an Expanded Cabinet ............................................... 35
FIGURE 33 - Use Gasket (P/N 028-11873-010) to Door Frame at Shipping Split .................................................. 35
FIGURE 35 - Come-A-Long Attached to a Section .................................................................................................36
FIGURE 36 - Remove Lifting Lugs in Expanded Cabinet........................................................................................36
FIGURE 37 - Electrical Connector (Not Connected) ...............................................................................................36
FIGURE 38 - Electrical Connectors (Connected) ....................................................................................................36
FIGURE 39 - Remove and Reposition Shipping Split Angle ...................................................................................37
FIGURE 40 - Bring Shipping Splits Together ...........................................................................................................37
FIGURE 41 - Fasten Bottom Lifting Lugs ................................................................................................................37
FIGURE 42 - Corner Connector Hole Plug (P/N 021-19568-000) ...........................................................................38
FIGURE 43 - Tiered AHU ........................................................................................................................................38
FIGURE 44 - Second Tier Tie-Down Fastener Pack (P/N 386-03419-000) ............................................................ 38
FIGURE 45 - Apply Gaskets to Top Panel on Bottom Tier ......................................................................................38
FIGURE 46 - Guide Brackets Together ...................................................................................................................39
FIGURE 47 - Lights Tier Transition Drawing ...........................................................................................................39
8
Issue Date: 07/03/2018 Form PA102.20-N1