The followings table shows the preset key assignment and which combinations are possible:
Function/push-
Up short
button
Menu
White balance
Light source on/off
■
Photo
■
Video
■
Brightness +
■
Brightness -
■
Saturation +
■
Saturation -
■
Digital zoom +
■
Digital zoom -
■
Sharpness +
■
Sharpness -
■
Contrast +
■
Contrast -
■ (default)
Empty
Return to factory settings
In order to return to factory settings:
►
Start menu (button A 20 (up), press and hold).
►
Mark "System setting".
►
Actuate button B 21 (right). A submenu appears.
►
Select "Return to default settings".
End application
►
Press the "Power off" switch 1 on the camera control unit.
►
Disconnect light guide cable.
►
Disconnect endoscope.
►
To completely disconnect the device from the power supply, remove the
plug from the mains connector 6 on the rear of the device.
6.
Validated reprocessing procedure
6.1
General safety instructions
Note
Adhere to national statutory regulations, national and international stan-
dards and directives, and local, clinical hygiene instructions for sterile pro-
cessing.
Note
For patients with Creutzfeldt-Jakob-disease (CJD), suspected CJD or possi-
ble variants of CJD, observe the relevant national regulations concerning
the reprocessing of products.
Note
Successful processing of this medical device can only be ensured if the pro-
cessing method is first validated. The operator/sterile processing technician
is responsible for this.
The recommended chemistry was used for validation.
Top long
Down short
■ (default
and fixed)
■
■
■
■
■
■
■
■
■
■
■
■
■ (default)
Down long
Left short
■
■ (default)
■
■ (default)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Note
If there is no final sterilization, then a virucidal disinfectant must be used.
6.2
Single-use products
WARNING
Risk of infection for patients and/or users and impairment of product
functionality due to reuse. Risk of injury, illness or death due to con-
tamination and/or impaired functionality of the product!
►
Do not reprocess the product!
Designation
Disposable sterile cover
6.3
General information
Dried or affixed surgical residues can make cleaning more difficult or inef-
fective and lead to corrosion. Therefore the time interval between applica-
tion and processing should not exceed 6 h; also, neither fixating pre-
cleaning temperatures >45 °C nor fixating disinfecting agents (active
ingredient: aldehydes/alcohols) should be used.
Excessive measures of neutralizing agents or basic cleaners may result in
a chemical attack and/or to fading and the laser marking becoming
unreadable visually or by machine for stainless steel.
Residues containing chlorine or chlorides e.g. in surgical residues, medi-
cines, saline solutions and in the service water used for cleaning, disinfec-
tion and sterilization will cause corrosion damage (pitting, stress corro-
sion) and result in the destruction of stainless steel products. These must
be removed by rinsing thoroughly with demineralized water and then dry-
ing.
Additional drying, if necessary.
Left long
Right short
■
■
■
■
■ (default)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■ (default)
Art. no.
JG904
en
Right long
■ (default)
■
■
■
■
■
■
■
■
■
■
■
■
■
■
11