Page 2
Assemblers and other persons who are not employed by or otherwise directly affiliated with or authorized by Siemens or one of its affiliates are directed to contact one of the local offices of Siemens or one of its affiliates before attempting installation or service pro- cedures.
• detector and • syngo Acquisition Workstation. Depending on the installation configuration, some points may be omitted. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 4 Medical Solutions Rev. 02 09.04 CS SD 24...
A non-invasive digital kV meter If not available in the district, a scope can be used instead Tab. 1 Meters, appliances and tools MAMMOMAT Novation SPB7-250.815.02 Page 2 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Standard installation and service tools Torque wrench for bolting the stand/ console to the floor Electrical screwdriver with adjustable torque is recommended Tab. 3 Tools MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 4 Medical Solutions Rev. 02 09.04 CS SD 24 System...
Page 10
1 - 4 Prerequisites This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Maintenance measurements must be made according to the DHHS Maintenance Instructions (SPB7-250.662.01...) and the DHHS Supplements to the instructions for use (SPB7-250.661.01...). Results must be recorded in DHHS Measurement certificates (SPB7-250.663.01...). MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 4 Medical Solutions Rev. 02 09.04...
They may cause severe injury. These strips must always be applied onto the edges of the metal curtain during service and maintenance work. MAMMOMAT Novation SPB7-250.815.02 Page 2 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
The Acquisition Workstation service software is web-based and can be started from the Options application menu. • BRICK The BRICK service software can be accessed via the Acquisition Workstation. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 4 Medical Solutions Rev. 02 09.04...
200 min. 30 max. 300 min. 45 max. 400 min. 60 max. 500 min. 75 Tab. 1 Delay times between two exposures MAMMOMAT Novation SPB7-250.815.02 Page 4 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Connect the cable to the lamp holder in series with the power supply. CAUTION When connecting the exposure lamp to the Master board, make sure that the electrical load does not exceed 24VAC / 25W MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 6 Medical Solutions Rev. 02 09.04...
Mains Frequency: 50 or 60 Hz Maximum load: 10kVA (momentary) and 0.8 kVA (long time load). Fuse: 25 A (external) 208 -> 400 V. MAMMOMAT Novation SPB7-250.815.02 Page 2 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Fig. 3Incoming mains cable Connect the incoming mains cable to the mains terminal (Fig. 3) at the bottom of the back of the stand. Strain-relieve the incoming mains cable. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 6 Medical Solutions Rev. 02 09.04...
(generator) are on: LED check 28 VP 5 VF - 15 V + 15 V 28 VS Tab. 2 LED check MAMMOMAT Novation SPB7-250.815.02 Page 4 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
V3—Power status. A green LED that lights to indicate that the PXCM is provid- ing power to the Detector. Check that the operating mode dr is displayed on the control console. Check if the noted exposure parameters are restored correctly. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 6 Medical Solutions Rev. 02 09.04...
Rotate the swivel arm system to 0 degrees by pressing one of the switches for clockwise rotation on the supporting arm. System and mains OFF. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Fig. 2 Opening the box Remove all of the other packing material covering the inner box in which the detector is located. NOTE Do not cut the lifting band. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 6 Medical Solutions Rev. 02 09.04...
Page 22
Fig. 4 Remove packing material Slide the lifting band from the inner box. Lift out the detector and carefully remove from wrapper. MAMMOMAT Novation SPB7-250.815.02 Page 2 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 23
You’ll find all documents required for sending it enclosed in the detector package (black box). Enter the detector serial number, your district address and instal- lation date before you sen it. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 6 Medical Solutions Rev. 02 09.04...
Connect the detector cable (3/Fig. 6) to the cable coming out of the wing (2/Fig. 6). Mount the cover over the detector cable with 2 screws. Make sure that no cables are squeezed. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Connect the cables (5/Fig. 7) for the magnification table, according to the labels, on both sides. WARNING Make sure that the cables are connected according to the labels, otherwise the D805 will burn up. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 6 Medical Solutions Rev. 02 09.04...
Mount the top wing cover with 4 screws. Slide the detector fibre cover carefully over the detector and fasten it with 6 screws at the bottom of the cover. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Connect ground wires (3/Fig. 1) to patient handles (4/Fig. 1). Side covers Screws in different sizes are included in the delivery. Fig. 2 Covers and sign MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 12 Medical Solutions Rev. 02 09.04...
Risk of damage. Be careful while attaching the front cover. Fasten the front cover to the side covers with two short screws (5/Fig. 2). MAMMOMAT Novation SPB7-250.815.02 Page 2 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Fit the rear cover (4/Fig. 3) to the stand and fasten it with screws (5/Fig. 3) and contact washers (6/Fig. 3). NOTE Be careful not to damage the cables at the cable outlet! MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 12 Medical Solutions Rev. 02 09.04...
Place the Stand cap on the top of the MAMMOMAT stand (2/Fig. 4). Face shield Fig. 5 Face shield Slide the face shield (1) onto the holder for external diaphragms.Checking the swivel arm system MAMMOMAT Novation SPB7-250.815.02 Page 4 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
(+135 degrees clockwise and -180 degrees counterclockwise). The projection angle is shown on the display at the lower part of the stand. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 12 Medical Solutions Rev. 02 09.04...
"Metal Curtain" on Page 2 - 2. Press the buttons for upward and downward movement (3/Fig. 6) of the swivel arm system. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
The button will latch and all motorized movements of the equipment will be blocked ("Er 813" shall appear). To reset the emergency stop button, turn it clockwise. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 7 of 12 Medical Solutions Rev. 02 09.04...
(1/Fig. 9). The field light shall go out automatically after a preset period of time (normally 20 s.). Fig. 9 Foot switch MAMMOMAT Novation SPB7-250.815.02 Page 8 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Check the function of the knobs for manual compression/decompression (3/Fig. 10). Place a piece of soft material on the object table, for example a rolled up towel or a piece of foam rubber (4/Fig. 10). MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 9 of 12 Medical Solutions Rev. 02 09.04...
Page 36
Press the foot switch for motorized compression to move the compression plate downwards while simultaneously pressing the compression plate in the opposite direction by hand. MAMMOMAT Novation SPB7-250.815.02 Page 10 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Increase/decrease the tautness factor by e.g. 10 the first time. Let the customer use this setting for at least two weeks before further changes are made. OPCOMP has been thoroughly tested by Siemens. If any factors NOTE are changed, OPCOMP will no longer be an optimization of com- pression force and image quality according to Siemens’...
Check that the exposure release is blocked during the following conditions: • No patient is registered. • No compression plate is mounted. • The wing is not in position. MAMMOMAT Novation SPB7-250.815.02 Page 12 of 12 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Be aware, that with the AEC mode on, a pre-exposure of 50 ms is done. Select the correct trigger on the scope, so you get the pre-expo- sure and the all the exposure times. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 6 Medical Solutions Rev. 02 09.04...
Page 40
1 V/T (1 T <=> 40 mA) 132 mA 1 V/T (1 T <=> 40 mA) 0.9 s 0.2 s/T 0.72 s 0.2 s/T MAMMOMAT Novation SPB7-250.815.02 Page 2 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Record the measured kV and mAs value in the "Startup Protocol" on Page 11 - 1 Change the setting and continue with the next measurement until you have completed all measurements from the table above. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 6 Medical Solutions Rev.
Record the measured kV and mAs value in the Startup Protocol, page 11 - 1. Change the setting and continue with the next measurement until you have completed all measurements from the table above. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Record the measured kV and mAs value in the Startup Protocol, page 11 - 1. Change the setting and continue with the next measurement until you have completed all measurements from the table above. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 6 Medical Solutions Rev.
Page 44
6 - 6 X-ray tube checks This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
The x-axis is located at the object table chest wall side edge. Fig. 1 Collimator calibrations • Moving the collimator OUT is done by INCREASING the YC value and DECREASING the YS, XL and XR values. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 6 Medical Solutions Rev. 02 09.04...
Collimator calibration is carried out for each focus including the field light focus. Connect the compression plate simulator and the collimator mounted plexi phan- tom. MAMMOMAT Novation SPB7-250.815.02 Page 2 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 47
Measure the white line thickness at each image edge with the application GUI and adjust the corresponding XL, XR, YC and YS values with the service software Start an exposure. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 6 Medical Solutions Rev.
Compare the image with the reading of the X-ray cross on the detector when the light field is turned on. Adjust the difference with the Service Software. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Fig. 4 Collimator wing difference calibration Start the service software on the Service PC and select: Configuration -> Collimator -> Calibration of wing differance Save the calibration and Exit the Service Software. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 6 Medical Solutions Rev. 02 09.04...
Page 50
7 - 6 Collimator Adjustment This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 6 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
If reinstalling factory default parameters, all previously entered measured data (HVL val- ues and Dose exchange factors) will be lost. However, the measured data should already be noted in the document Radiographic Handbook. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 10 Medical Solutions Rev.
The label is found in register 3 of the Technical Manual binder. affix the new label here mAs / mGy Program Auto Lim. Mo Rh WARNING Fig. 2 MAMMOMAT Novation SPB7-250.815.02 Page 2 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Repeat the procedure described in steps 2-5 for the other programs used. Record the measured values in the Startup Protocol, page 11 - 1. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 10 Medical Solutions Rev.
Mount the Collimator Mounted Plexi phantom and the compression plate simulator. Register or create a patient and submit with Exam. Fig. 3 Calibration - Patient register MAMMOMAT Novation SPB7-250.815.02 Page 4 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 55
The AEC sensors are drawn on the compression plate. Start an exposure. Measure the following values and add them to the table at step 4: MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 10 Medical Solutions Rev. 02 09.04...
Page 56
H and D Settings" and repeat the H & D dose check for Mo/Mo again. Record the measured values in the "Startup Protocol" on Page 11 - 1 . MAMMOMAT Novation SPB7-250.815.02 Page 6 of 10 Siemens AG System Rev. 02 09.04 CS SD 24...
H and D Settings" and repeat the H & D dose checks for Mo/Rh and W/Rh again. Record the measured values in the "Startup Protocol" on Page 11 - 1 . MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 7 of 10 Medical Solutions Rev.
The BRICK software switches to a higher user level, thus a Username and Password have to be entered. Username: root Password: ****** MAMMOMAT Novation SPB7-250.815.02 Page 8 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 59
100,80,60 in the High Dose Scal- ing Value field and click Change High Dose Scaling to save it. Proceed from where you have been referenced from. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 9 of 10 Medical Solutions Rev.
Page 60
8 - 10 Checking dose settings This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 10 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
The compression plate simulator is mounted on the MAMMOMAT. Checking visibility of grid lines Register or create a patient Grid lines test and submit with Exam. Fig. 1 Calibration - Patient register MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 20 Medical Solutions Rev. 02 09.04...
Page 62
Exposure Exp Mode mAs Tube Angle (yes/no) AEC "H" AEC "H" + 60 AEC "H" - 60 Tab. 1 Checking visibility of grid lines MAMMOMAT Novation SPB7-250.815.02 Page 2 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Note the result in the Tab. 2. Choose the next image that had visible grid lines in the list and start over with step 3 until all images are evaluated. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 20 Medical Solutions Rev.
To minimize the risk that the high voltage is active when the grid is standing still, the time that the high voltage is disabled should be as long as possible. Move the grid to the left end position. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 65
9 - 5 Loosen the three screws. Now it's possible to adjust the grid switch (S1) alongside the grid (see Fig. 4). Fig. 4 Adjust grid switch S1 MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 20 Medical Solutions Rev. 02 09.04...
Page 66
A wheel is mounted on the left side of the grid motor (M1), on the wheel there is a slits which activates the grid switch (S1). Move the grid to the left end position. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 67
Open the carbon detector cover. Make sure the grid in mounted in parallel to the detector and lined up to the front of the table. The front switch has to be engaged. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 7 of 20 Medical Solutions Rev.
Log into local service Options -> Service -> Local Service. NOTE The Service Level 1 or higher is necessary to do the Gain Calibra- tion. MAMMOMAT Novation SPB7-250.815.02 Page 8 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 69
9 - 9 Select Acquisition System. Fig. 8 Service Home Page As a result you will get the following screen. Fig. 9 Acquisition System Menu MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 9 of 20 Medical Solutions Rev. 02 09.04 CS SD 24...
Page 70
The "temperature" field in this picture shows a value of "3045", due to a bug in the software. The actual temperature value is "30.45". MAMMOMAT Novation SPB7-250.815.02 Page 10 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 71
Press the Start button, to start the calibration. Fig. 11 Calibration - Start Create or register the patient Calibration and submit with Exam. Fig. 12 Calibration - Patient register MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 11 of 20 Medical Solutions Rev. 02 09.04...
Page 72
Check the image quality of the image. No objects or artifacts shall be visible in the image. If you Accept the image, the image will be used for Gain Calibration. MAMMOMAT Novation SPB7-250.815.02 Page 12 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 73
Procedure: Calibration Procedure and proceed with step 12 until you have a total of 8 images. Click Done to exit the Calibration. Close the examination. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 13 of 20 Medical Solutions Rev. 02 09.04...
The Service Level 5 or higher is necessary to do the Bad Pixel Mapping. Select Acquisition System. Fig. 14 Service Home Page MAMMOMAT Novation SPB7-250.815.02 Page 14 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 75
As a result you will get the following screen. Fig. 15 Acquisition System Menu Click the Bad pixel mapping link. Fig. 16 Bad Pixel Mapping - Enter MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 15 of 20 Medical Solutions Rev. 02 09.04...
Page 76
Fig. 17 Bad Pixel Mapping - start If you want to end the Bad Pixel Mapping operation at this point, NOTE click the "Cancel" button. MAMMOMAT Novation SPB7-250.815.02 Page 16 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 77
Image Quality 9 - 17 Register the pre defined patient Calibration and submit with Exam. Fig. 18 Bad Pixel Mapping - Patient register MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 17 of 20 Medical Solutions Rev. 02 09.04 CS SD 24...
Page 78
Image acquisition is in progress ..Saving processed Image ..Loading Image ..Click the Accept or Reject button. MAMMOMAT Novation SPB7-250.815.02 Page 18 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 79
NOTE collimation or misalignment or if there are any artifacts from debris or obstructions. Click Done to exit the Bad Pixel Mapping. Close the examination. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 19 of 20 Medical Solutions Rev. 02 09.04 CS SD 24...
Make a note in the Startup Protocol page 11 - 1, that the Quality Control Manual tests have been performed MAMMOMAT Novation SPB7-250.815.02 Page 20 of 20 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Go into the service software and select Utilities -> Escape to OS and enter the following command in the command field. start telnet brick A username and password have to be entered. Username: root Password: ****** MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 4 Medical Solutions Rev. 02 09.04 CS SD 24...
Page 82
MM - minutes yy - year The following example sets the system to 3:10 p.m. on November 21, 2004: brick# date 1121031004 MAMMOMAT Novation SPB7-250.815.02 Page 2 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
(Mains input terminal) and all metallic parts of the equipment which the patient/operator may come in contact with, incl. all object tables. The protective ground resistance must not exceed 0.1 Ω. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 4 Medical Solutions Rev.
Installation or Start up problems occurred. Place a copy of the SP Q Quality Certificate in the technical documentation binder. • The Startup Protocol and the Installation Protocol remain with the system. MAMMOMAT Novation SPB7-250.815.02 Page 4 of 4 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Luminance meter (measures the light intensity from the X-ray field) Dose meter Ion chamber Densitometer A non-invasive digital kV meter Tab. 1 Auxiliary materials MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 10 Medical Solutions Rev. 02 09.04 CS SD 24 System...
All Covers are mounted......... . . ❏ ❏ The temperature logger was sent to DirectRay Cooperation (DRC) ..MAMMOMAT Novation SPB7-250.815.02 Page 2 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 87
........MAMMOMAT Novation Siemens AG SPB7-250.815.02...
_____V x ( _____s + _____s + _____s) x 40 mA = ______ mAs 10 mAs Mo/Mo Tab. 2 Tube high voltage, current and mAs values MAMMOMAT Novation SPB7-250.815.02 Page 4 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 89
_____V x ( _____s + _____s + _____s) x 40 mA = ______ mAs Display ______ mAs W/Rh Tab. 2 Tube high voltage, current and mAs values MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 10 Medical Solutions Rev. 02 09.04 CS SD 24...
Results from the chapter "Checking the AEC dose settings" on Page 8 - 4. Anode / Dose value Pixel value Filter Mo/Mo 28 kV Mo/Rh W/Rh Tab. 5 AEC Dose Settings MAMMOMAT Novation SPB7-250.815.02 Page 6 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Number of employees who were employed in the period Total (Mh) Man hours, number of accumulated hours multiplied by number of employees MAMMOMAT Novation SPB7-250.815.02 Page 8 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
__________________________________________________________________________ __________________________________________________________________________ A copy of this remains at the system and is filed in the Assembly/Installation folder. Place, date Installation team employee Siemens project manager/ person responsible for the project Name in block letters Name in block letters MAMMOMAT Novation Siemens AG SPB7-250.815.02...
Page 94
11 - 10 Startup Protocol This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 10 of 10 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Isolation is the first step and should be done by using internally-generated image patterns in the image chain to determine where exactly the artifact is being produced (“what is/ what is not” the artifact analysis). MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 8 Medical Solutions Rev.
Page 96
Perform the bad pixel correction. ( Pixels and Lines ing. refer to "Creation of new pixel map" on Page 9 - 14) MAMMOMAT Novation SPB7-250.815.02 Page 2 of 8 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 97
Distorted image with Detector defective. Detector might have to be replaced 256 blocks contact the Service Center. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 3 of 8 Medical Solutions Rev. 02 09.04 CS SD 24 System...
Programmable Logic Device on the AEC board (D701). Flash Memory device on the AEC board (D701). ® ® Operating System, e.g. Microsoft Windows MAMMOMAT Novation SPB7-250.815.02 Page 4 of 8 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
If the IrDA-port was disabled in the computer BIOS, it should not be present in the list of available hardware. If the IrDA is present anyway and its icon is not marked with a red cross: Double-click on the device row. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 5 of 8 Medical Solutions Rev. 02 09.04...
Choose Control Panel. Choose System. Choose the tab Hardware. Press the button Device Manager. Expand the row Ports. Double-click on the COM1 row. MAMMOMAT Novation SPB7-250.815.02 Page 6 of 8 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 101
12 - 7 Choose the tab Port Settings. Press the button Advanced. Uncheck the check box Use FIFO Buffers. Exit the dialog by pressing the OK button. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 7 of 8 Medical Solutions Rev. 02 09.04...
Page 102
12 - 8 Appendix This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 8 of 8 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...
Page 103
Added time adjustment for the BRICK. Corrected the startup protocol regarding the opdima changes. Added a table for the auxiliary materials used with the installa- tion. MAMMOMAT Novation Siemens AG SPB7-250.815.02 Page 1 of 2 Medical Solutions Rev. 02 09.04...
Page 104
13 - 2 Changes to previous version This page intentionally left blank. MAMMOMAT Novation SPB7-250.815.02 Page 2 of 2 Siemens AG System Rev. 02 09.04 CS SD 24 Medical Solutions...