Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Prominence Home 40278
Summary of Contents for Prominence Home 40278
-
Page 2: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1. Canopy 13. Fitter Plate 2. Canopy Cover 14. Fitter Plate Screw (x3) 3. Mounting Bracket 15. Switch Housing Cap 4. Mounting Bracket Screw 16. -
Page 3: Mounting Options
DIMENSION REFERENCE A. 13.58 in. B. 9.21 in. C. 6.74 in. D. 5.13 in. MOUNTING OPTIONS Three Mounting Options Downrod Mount Closemount Angle Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. - Page 5 ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 2. Remove the mounting bracket by removing the two mounting bracket screws from the round holes in the Mounting Bracket canopy. Then loosen the other two mounting bracket Screws screws from the J-shaped slots.
- Page 6 ASSEMBLY INSTRUCTIONS DOWNROD INSTALLATION: Downrod Clip 5. Remove the downrod clip and downrod pin from the Downrod downrod. Then partially loosen the two set screws in the yoke at the top of the motor assembly. Downrod Pin Yoke Set Screw Motor Assembly 6.
- Page 7 ASSEMBLY INSTRUCTIONS 9. Use wire connectors to connect the fan wires to the power supply wires according to the wiring diagram and Black (hot) the following instructions: White (neutral) Wire • Connect the green wire from the downrod and mounting Bare/Green Connector (ground)
- Page 8 ASSEMBLY INSTRUCTIONS 13. Note: If you wish to install the fan without the light kit, proceed to Step16. To install the light kit, remove the three fitter plate Fitter Plate Fitter Plate screws from the fitter plate. Then connect the single-pin Screw connector from the fitter plate to the single-pin connector in the light kit--blue to black and white to white.
- Page 9 ASSEMBLY INSTRUCTIONS 17. Attach the pull chain extensions to each of the pull chains. The fan pull chain extends from the Fitter Plate side of the light kit and the light pull chain extends Fitter Plate Screw from the center of the light kit. Light Pull Chain Fan Pull Chain Extension...
- Page 10 OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain has two positions to control the light, ON and OFF. 2.
-
Page 11: Troubleshooting
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. -
Page 12: Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. Central time. Model Name: 52” Glenmont Ceiling Fan Model No: 50388 - Antique Pewter 50389 - Distressed White The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser.