Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Prominence Home 51028
Summary of Contents for Prominence Home 51028
-
Page 2: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1. Canopy 14. Fitter Plate Screw (x3) 2. Canopy Cover 15. Switch Housing 3. Mounting Bracket 16. Light Kit 4. Mounting Bracket Screw 17. -
Page 3: Mounting Options
DIMENSION REFERENCE A. 20.6 in. B. 13 in. C. 13.2 in. D. 5.8 in. MOUNTING OPTIONS Downrod Mount Closemount Mount Angle Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Closemount method is best suited for ceilings lower than 8 feet. It does not utilize the downrod. Downrod Mount is best suited for ceilings 8 ft. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. - Page 5 ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 2. Remove the mounting bracket by removing the two Mounting Bracket mounting bracket screws from the round holes in the Screws canopy. Then loosen the other two mounting bracket screws from the J-shaped slots.
- Page 6 ASSEMBLY INSTRUCTIONS DOWNROD INSTALLATION 5. Remove the downrod clip and downrod pin from the Downrod Clip Downrod downrod. Then partially loosen the two set screws in the yoke at the top of the motor assembly. Downrod Pin Yoke Set Screw Motor 6.
- Page 7 ASSEMBLY INSTRUCTIONS 9. Use wire connectors to connect the fan wires to the Black (hot) power supply wires according to the wiring diagram and the following instructions: White (neutral) Bare/Green • Connect the green wire from the downrod and mounting (ground) bracket to the bare/green (ground) supply wire.
- Page 8 ASSEMBLY INSTRUCTIONS 13. Note: If you wish to install the fan without the light kit, proceed to Step17. To install the light kit, remove the three fitter plate Fitter Plate Screw Fitter Plate screws from the fitter plate. Then connect the 9-pin connector from the fitter plate to the 9-pin connector in Switch Housing the light kit.
- Page 9 ASSEMBLY INSTRUCTIONS 17. To install without the light kit, remove the Lock Washer Hex Nut preassembled hex nut and lock washer from the Switch Housing threaded rod inside of the switch housing. Remove light kit from the switch housing, then install the plug button into the center hole of the switch housing.
- Page 10 OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control fan speed. One pull is HIGH, two is MEDIUM, three is LOW and four turns the fan OFF. The light pull chain has two positions to control the light, ON and OFF. 2.
-
Page 11: Troubleshooting
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. -
Page 12: Limited Lifetime Warranty
Model Name: 60” Denon Ceiling Fan Model No: 51029 - Brushed Nickel 51028 - Espresso The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer...
Need help?
Do you have a question about the 51028 and is the answer not in the manual?
Questions and answers