Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Prominence Home Bolivar 80099
Summary of Contents for Prominence Home Bolivar 80099
-
Page 2: Package Contents
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: PACKAGE CONTENTS 1. Canopy 11. Fitter Plate 2. Canopy Cover 12. Light Kit 3. Mounting Bracket Screw 13. Glass Bowl (x4) 14. Owner’s Manual 4. Mounting Bracket 15. -
Page 3: Mounting Options
DIMENSION REFERENCE A. 13.88 in. B. 9.63 in. C. 2.4 in. D. 11.33 in. E. 5.13 in. MOUNTING OPTIONS Two Mounting Options Downrod Mount Angled Ceiling Mount (Up to 16 degrees) Choose one of the following mounting options: Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SAVE INSTRUCTIONS. CAUTION: All set screws of the fan must be checked and retightened where necessary before installation. To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades or cleaning fan. - Page 5 ASSEMBLY INSTRUCTIONS 1. Turn OFF the electrical power at the main fuse or circuit breaker. 2. Remove the canopy from the mounting bracket by removing the two mounting bracket screws from the Mounting Bracket round holes in the canopy. Then loosen the other two Screw mounting bracket screws from the J-shaped slots.
- Page 6 ASSEMBLY INSTRUCTIONS 5. Loosen but do not remove the two set screws in the yoke of the motor assembly. Then remove the downrod Downrod Clip Downrod pin and downrod clip from the bottom of the downrod. Downrod Pin Set Screw Yoke 6.
- Page 7 ASSEMBLY INSTRUCTIONS 9. Install the ball end of the downrod into the opening of the mounting bracket. Rotate the fan in the mounting Mounting bracket until the slot in the ball end of the downrod Slot Bracket engages the tab in the mounting bracket. DANGER: The fan and/or downrod should not rotate Downrod Clip...
- Page 8 ASSEMBLY INSTRUCTIONS 13. Install the blade arm to the underside of the motor Motor Blade Arm assembly with motor screws previously removed (Step 4, page ). Tighten with Phillips screwdriver. Repeat for each blade arm. Note: The slot in the underside of the fitter plate allows screwdriver access to motor screws.
- Page 9 ASSEMBLY INSTRUCTIONS 16. Loosen two and completely remove the third thumbscrew by turning them counterclockwise. Lift the glass shade onto the light kit and reinstall the thumbscrew. Tighten all three thumbscrews. Glass Bowl Thumbscrew Light Kit 17. Attach the appropriate pull chain extensions to each of the pull chains.
- Page 10 OPERATING INSTRUCTIONS 1. The fan pull chain has four positions to control the fan speed. One pull is HIGH, two is MEDIUM, three is LOW, and four turns the fan OFF. The light pull chain turns the light ON and OFF. Note: When facing the reverse switch, the pull chain on the left controls the fan and the pull chain on the right Reverse Switch...
-
Page 11: Troubleshooting
TROUBLESHOOTING If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. -
Page 12: Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY To obtain Service, please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. Central time. Model Name: 52” Ceiling Fan 80099, 80100, 80101 Model No: The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser.