Hussmann Excel FWG Installation & Operation Manual page 6

vi vi
REVISION HISTORY
REVISION L
1. FWGH and FWGEH Load Limit Profile
2. FWGH and FWGEH Bolt Location Drawings Page
1-10, 1-12
3. Added Replacing Product Side Heater
4. Flue Glass for FWGH 1-21
REVISION K
1. Updated Prep Merchandiser #2, page 1-5.
2. Added Replacing Interior Panels and Louvers, page
1-14.
3. Added coil cleaning, page 5-3.
4. Revised Step 6, page 6-8.
REVISION J
1. Removed adjustable legs, page 1-3, throughout.
REVISION I — not used
REVISION H
1. Added 3-in. space requirement from walls, page 1-3
2. Added merchandiser lineup bumper instruction to
Offsetting Bumper Section, pages 1-15 to 1-18.
3. Added Drip Piping Support 24 in. requirement from
Drain Hubs, pages 3-2 and 3-3
4. Added Rail Heater wiring harness drawings, pages
6-3 to 6-6.
REVISION G
1. Revised drip piping pitch, page 3-1.
2. Added stainless steel rail maintenance, page 5-2.
REVISION F
1. Added Joining Merchandisers in Line
(3 photos). page 1-6.
2. Added Bumper Retainer Bracket drawing, page 1-7.
3. Added Joining End Merchandiser to Wide Island (3
photos), page 1-8.
4. Added Socket Adapter Photo, page 1-10, 1-12.
5. Removed "V" from drawing FW to FWE,
page 1-12.
6. Added Bumper Retainer photo, page 1-15.
7. Revised instruction information, page 1-15.
8. Added NOTES, page 1-6 to 1-9.
9. Changed bumper tool information, page 1-14.
10. Added Replacing Hand Rail Heater, page 6-3 to
6-4.
P/N 0467434_N P/N 0467434_P
REVISION E
1. Added ANSI definitions, page iv.
2. Added bumper removal instruction to Offsetting
3. Added offsetting plastic hand rail procedure, page
4. Added SS Top Rail Joint Trim, page 1-16.
5. Added Installing Flue Glass — FNG & FIG, page
6. Updated NSF Thermometer, pages 4-3 and 4-4.
7. Added center flue removal instruction, page 5-3.
8. Updated WARNING, CAUTION, and NOTICE
9. Added URL, contact phone numbers to bottom of
REVISION D
1. Changed to factory installed flange nut fastener
2. Changed
3. Changed joining order, page 1-8.
4. Changed 3 in. Hex Head screw to 3
5. Changed
6. Added fastener location for joining FWG to
REVISION C
1. Added URL, contact phone numbers, page iii.
2. Removed alignment pin from joining sequence,
3. Changed
4. Changed
5. Changed 4 in. screw to 4
6. Deleted one location from end joining, page 1-10.
7. Added refrigeration shroud, page 2-1.
8. Added Do not use coarse paper towels, page 5-1.
REVISION B
1. Added joining location, pages 1-8 and 1-9.
2. Changed fastening order for joining, page 1-10.
3. Added Louver Retainer, page 5-2.
4. Added Wireway Cover, page 6-4.
REVISION A
1. Added note, page 3-2.
ORIGINAL ISSUE — September 2005
U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM
Bumper, pages 1-12 — 1-14.
1-15.
1-17.
boxes throughout.
even-numbered pages.
for joining end merchandiser to wide island parent,
page 1-7.
on page 1-8; affects joining
key
illustrations on pages 1-8 and 1-9.
screw, pages 1-8 and 1-10.
on page 1-10.
end key
FWEG, page 1-10.
pages 1-5, 1-6, 1-8, 1-9, 1-10 and 1-13.
on page 1-8.
key
on page 1-10.
end key
1 / in. Hex Head
2
/ in. bolt, page 1-10.
1
TAP
2