Medium temperature. bulk produce and bakery merchandisers (34 pages)
Summary of Contents for Hussmann IMPACT ED1
Page 1
Joining Kit, making sure there is no breakage or damage. CAUTION DO NOT remove riders until case is in its final position. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) 5 /8 x 180 1 /2 x 120 3 /8...
Page 2
S S e e e e F F i i g g u u r r e e 1 1 . . Fig. 1. Removing items from case HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) ®...
Page 3
Fig. 2. Checking Alignment Pin and Light Rail Joining Bkt 5 /8 Apply 1 (321 mm) Fig. 3. Applying 1 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Light Rail Joining Bracket gasket to both cases 5 /8 in. Gasket to the Merchandiser...
Page 4
S S e e e e F F i i g g u u r r e e 4 4 , , D D e e t t a a i i l l C C . . HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)
Page 5
Alignment Pins Silicone DETAIL E. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) In addition, apply silicone around the perimeter of the front joining hole and over the top of the frame. S S e e e e F F i i g g u u r r e e 5 5 , , D D e e t t a a i i l l s s D D and E E .
Page 6
Front Gasket DETAIL G. Silicone DETAIL H-b. Fig. 6. Applying Top and Front Gasket Pads HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Silicone Gasket DETAIL H-a. 1 /2 (13 mm) X 5 /8 in. (41 mm) 1 /2 (13 mm) X 1 /2 (13 mm)
Page 7
S S e e e e F F i i g g u u r r e e 7 7 , , D D e e t t a a i i l l I I . . CASE 1 Alignment Pins DETAIL I. Fig. 7. Leveling Merchandisers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) The complete lineup must be leveled to the highest point of the floor. After the first merchandiser has been set, position the second so the end frames touch.
Page 8
S S e e e e F F i i g g u u r r e e 1 1 1 1 . . CAUTION Use only specified fasteners. Longer screws will penetrate rear sill. HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Fig. 8. Front Lighting Rail Joining Plate Top Extrusion Fig. 10. Joining Plate in place Rear Sill Fig.
Page 9
All Fasteners are drawn out of scale and larger for clarity Fig. 13. Fastening Front of Cases Together (Sequence A) HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) CASE P/N 0420058 Follow the sequence cor- rectly when bolting the cases together.
Page 10
Front Electrical Wires always here DETAIL J. Fig. 14. Fastening Rear of Cases Together (Sequence B) HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) WARNING Use caution when installing fasteners around wiring or refrigeration lines inside of struts.
Page 11
Impact Service Merchandisers Joining Instruction Fig. 15. Fastening Top Fronts of Cases Together (Sequence C) HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) CASE CASE P/N 0420058 Fasten the top rear of the cases together using Cap Screws (Item – 20), Flat Washers (Item –...
Page 12
S S e e e e F F i i g g u u r r e e s s 1 1 6 6 , , Joint Cover Silicone Joint Fig. 16. Installing and Sealing Joint Cover HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Bottom Joint Cover Case Bottom...
Page 13
Impact Service Merchandisers Joining Instruction Fig. 17. Sealing Case Joints HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) P/N 0420058 EALING THE OF THE Apply a smooth continuous bead of silicone over the Exterior Top Joint of the cases.
Page 14
P/N 0420058 Install the Splashguard Joint Support (Item – 25) to the splashguard retainer using Screws (Item – 26). Splashguard Retainer Fig. 18. Installing the Splashguard Joining Bracket and Splashguard HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) Splashguard ®...
Page 15
Fig. 19. Install Impact Bumper Retainer 2 Foot (610mm) Starter Bumper Full Length Bumper Fig. 20. Installing and offsetting Bumpers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.) P/N 0420058 NSTALL UMPERS Starting from left end of line- up, insert 2 foot (610 mm) starter bumper into the front Top Bumper Retainer.