Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fermax NEO MEET
Summary of Contents for Fermax NEO MEET
- Page 1 NEO MEET INSTALLER MANUAL...
- Page 2 Technical publication for information purposes edited by FERMAX ELECTRÓNICA S.A.U. FERMAX ELECTRÓNICA applies a continuous improvement policy, therefore it reserves the right to modify the contents of this document, as well as the product features hereof at any time and without prior notice. Any modification will be reflected in subsequent editions of this document.
-
Page 3: Table Of Contents
2.1. Stand placement 2.2. Attaching the monitor to the stand 2.3. Connection diagram 2.4. Wired alarm and doorbell sensors 2.5. Wiring of FERMAX MEET Relay Module Ref. 1616 3. TECHNICAL SPECIFICATIONS 4. LOCAL PROGRAMMING FROM THE MONITOR 4.1. Installer access 4.2. -
Page 4: Description
1 DESCRIPTION The following document is the Installation Manual for the NEO 7” MEET monitor, with firmware V03.00. Alarm mode LAN status Date and time Missed calls Eceived messages Do not disturb NEO MEET INSTALLER MANUAL... -
Page 5: Installation
To do this, snap the 4 connector anchors into the corresponding slots on the back of the monitor and push down on the monitor to attach it. Do not forget to pre-connect the ethernet network connectors, power supply and accessories, if applicable. NEO MEET INSTALLER MANUA... -
Page 6: Connection Diagram
12V +, -, 485+, 485-: Salida alimentación y conexión RS-485 para el Módulo de 10 Relés Ref. 1616. 2.4. WIRED ALARM AND DOORBELL SENSORS iring diagram, normally open sensor. Wiring diagram, normally closed sensor. Wiring diagram, normally open sensor, option 3C. NEO MEET INSTALLER MANUAL... -
Page 7: Wiring Of Fermax Meet Relay Module Ref. 1616
The Z8 sensor input is reserved for the internal tamper (monitor anti-sabotage). 2.5. WIRING OF FERMAX MEET RELAY MODULE REF. 1616 To use the actuator control function, a FERMAX MEET Relay Decoder Ref. 1616 must be installed. The connection to the monitor is through the RS-485 connector as shown in the following diagram. -
Page 8: Technical Specifications
Conversation time 120 secs. Time to answer the call 35 secs. Auto-on time 30 secs. Maximum recording log Maximum number of IP cameras Block 001-999 Apartment 0001-9899 Working temperature 10ºC 55º C Relative humidity 20-85% (without condensation) NEO MEET INSTALLER MANUAL... -
Page 9: Local Programming From The Monitor
It can be changed later for another of your choice. For security reasons, if the wrong PIN is entered three times in a row, the device will be blocked for 60 seconds. Once the correct PIN has been entered, the INSTALLATION SETTINGS options will appear: NEO MEET INSTALLER MANUA... -
Page 10: Basic Configuration Of The Monitor
• SYNC CODE: Synchronisation code with the rest of the devices in the apartment. Default value is 123456. • SOFTWARE IP: IP address of the PC where the MEET Management Software is installed (if any). • SW PIN: MEET Management Software ACCESS PIN code. The default option is 123456. NEO MEET INSTALLER MANUAL... -
Page 11: Configuring The Alarm Settings
Alarm will not be triggered during the arming countdown. • PANIC: The alarm will be triggered silently, i.e. by giving a warning to the control station, but without alarm sound on the monitor. NEO MEET INSTALLER MANUA... -
Page 12: Enable/Disable Functions
SLEEP or OUT mode is selected. 4.4. ENABLE/DISABLE FUNCTIONS Touch the icon to select which functions are to be available to the user and which functions are to be blocked. NEO MEET INSTALLER MANUAL... -
Page 13: Enable/Disable Function Icons On The Monitor
ICONS section. There are 2 pages, that can be selected by means of the “arrow” icons. Select wich function ICON do you want be visible in the MAIN MENU. The MAIN MENU will show the 8 selected function ICONS. NEO MEET INSTALLER MANUA... -
Page 14: Change Installer Pin
Make a note of the new PIN at your convenience. If you lose or forget your PIN, you should contact FERMAX’s Technical Department to receive instructions regarding its recovery. All the monitor programming will be lost. -
Page 15: Web Browser Programming
• Password: 6666 A form will appear with the different programming sections: SECCIONES DE PROGRAMACIÓN NOTES: Preferably use the Chrome browser The default identification data may have been changed from the local programming of the monitor. NEO MEET INSTALLER MANUA... -
Page 16: Device
• CONCIERGE X: Select the GU number to call. • TAG: Name that will be shown in the monitor when a call to concierge is being made. NEO MEET INSTALLER MANUAL... -
Page 17: Network Configuration
CONFLICT” prompt will appear, along with the MAC of the conflicting device. Both devices will not work properly until this issue is resolved. 5.4. IP CAMERA Designate the IP camera or cameras, accessible on the NETWORK, that will be available for viewing on this monitor. NEO MEET INSTALLER MANUA... -
Page 18: Sip
Internet server-based installations. It is usually port 5060. Check with your network administrator. • USER: Enter the SIP user name or extension to register on SIP server. • SIP PASS: Enter the SIP server extension password. NEO MEET INSTALLER MANUAL... -
Page 19: Advanced
Indicate the URL or URLs of the devices to which the calls will be forwarded. These URLs must have one of these formats: • sip: meetme_licensenumber@sip.fermax.com, in case of call divert to mobile using the MEET ME App, where meetme_licensenumber corresponds to the MEET ME username on the sticker of the monitor and used to configure the MEET ME App on the smartphone. -
Page 20: Actuators
Select the desired activation time with the RELAY TIME between 1 and 60 seconds. Select SAVE to confirm. NOTE: The control of devices by means of actuators requires the module Ref. 1616. Its installation is explained in section 2.5. Wiring of FERMAX MEET Relay Module Ref. 1616. NEO MEET INSTALLER MANUAL... -
Page 21: Pin Code
NOTES: Make a note of the new PIN at your convenience. If you lose or forget your PIN, you should contact FERMAX’s Technical Department to receive instructions regarding its recovery. All settings programmed into the monitor will be lost. 5.9. RESTORE Use this functionality to remotely reboot the monitor, or to restore it to factory settings. -
Page 22: Annex
Technical Bulletins, etc.) about the release of a new firmware update, as well as the improvements incorporated. Contact the FERMAX Technical Department if you wish to receive the corresponding update file. The firmware update is performed via the MEET System Upgraded Tool V 1.2.exe. -
Page 23: Regulations And Certification
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help. NEO MEET INSTALLER MANUA... - Page 24 Avd. Tres Cruces, 133 46017 Valencia Spain For more information, visit www.fermax.com Contact: tec@fermax.com www.fermax.com/contact...