Setup Requirements - Angelcare AC327 User Manual

• Replacement of a battery with an incorrect typcan
result in an explosion or the leakage of flammable
liquid or gas.
• Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, can
result in an explosion.
• Leaving a battery in an extremely high temperature
surrounding environment can result in an explosion or
the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may
result in an explosion or the leakage of flammable
liquid or gas.
• The mounting height of the Nursery Unit should be
less than 2 meter.
• The applied nameplate is located at the product rear
enclosure.
IMPORTANT SAFETY INSTRUCTIONS
38. Sensor Pad –
• If your cot does not have a solid, stationary, completely
flat, firm surface including a spring or slat base, place
a hard board between the cot base and the Sensor
Pad, to ensure correct operation (see specification on
STEP 2).
• The Sensor Pad functions with standard cot sprung
and foam mattresses and not memory foam (partial or
full), hollow frame construction mattresses and water
beds. Please consult Angelcare if unsure of mattress
compatibility.
39. This monitor uses public airwaves to transmit
signals. The Parent Unit may pick up signals or
interference from other nursery monitors in your
area. Your monitor may even be picked up by other
households. To protect your privacy, make sure both
units are turned OFF when not in use.
40. Power cord protection - Protect the
Adaptor's power cord from being walked on
or pinched by furniture or other items – Power
supply cords should be routed so that they are not likely
to be walked on or pinched by items upon or against
them, paying particular attention to cords and plugs,
convenience receptacle, and the point where they exit
SET UP REQUIREMENTS
WHAT'S IN THE BOX
Nursery Unit
1
Tabletop stand/Wall Mount (for Nursery Unit)
2
2 x AC Adaptors
3
Parent Unit
4
Lithium Ion Battery Pack (for Parent Unit)
5
Sensor Pad
6
CR2450 3V Battery (for Sensor Pad)
7
Hardware (for wall mounting)
8
WHAT YOU NEED
Hardboard, if the cot does not have a firm surface
(see specification on STEP 2).
Drill or screwdriver (for wall mounting).
4
from the product. The socket outlet should be installed
near the equipment and should be easily accessible.
Make sure to plug the adaptor to the socket outlet
nearest to the equipment and that is easily accessible.
To disconnect from mains, unplug the adaptor. STOP
using the Power Adaptor if it gets damaged or broken
in any way.
41. Only use attachments/accessories
and replacement parts specified by the
manufacturer. Any mounting of the product
should follow the manufacturer's instructions.
• DO NOT position this product on an unstable cart,
stand, tripod, bracket or table. The product may fall,
causing serious injury to a child or adult and serious
damage to the product.
• Use ONLY the stand sold with the product.
• Be sure replacement parts are supplied by Angelcare
and have the same characteristics as original part.
Unauthourised substitution may result in fire, electric
shock or fire.
42. Unplug this appliance during lightning
storms or when not used for long periods of
time.
43. Servicing - DO NOT attempt to service
this product yourself as opening or removing
covers (except battery door) may expose you to
dangerous voltage or other hazards.
• Power Supply – see Technical Specification within
this guide.
44. Overloading - DO NOT overload wall outlets,
extension cords or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
45. Nursery Unit Antenna - The antenna used
for this transmitter must be installed to provide a
separation distance of at least 8'' (20 cm) from all
persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
46. Cleaning - Disconnect all units before cleaning.
DO NOT immerse any part of the monitor in water. Clean
only with a dry cloth.
2
1
4
6
3
2X
5
7
8 2X