Related Manuals for Oneida Air Systems 8491685
Summary of Contents for Oneida Air Systems 8491685
- Page 1 OWNER’S MANUAL High Vacuum Dust Collector with SMART Boost and Air Lock 5 HP # XXS050334 U.S. Patent: #8491685, #8496719, #7247180 Appearance may vary slightly Rev: 05/17/2021 Doc. #ZBM000104...
-
Page 3: Table Of Contents
Table of Contents System Start-Up Information System Speci cations System Dimensions System Contents Assembly Instructions Maintenance Troubleshooting F.A.Q. Recommended Accessories Warranty Information Notes oneida-air.com... -
Page 4: System Start-Up Information
5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or failure to follow these directions). - Page 5 System Start-Up Information (Continued) d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).
-
Page 6: System Speci Cations
C ARTRIDGE FILTER Filter Media Type Izumi Axtar Spunbond Media Filter E ciency 99.9% @ 0.2-2.0 microns Filter Surface Area 220 Sq. Ft. SYSTEM DIMENSIONS AND CONSTRUC TION Barrel/Cyclone Body Heavy-gauge cold-rolled steel Inlet 7" Diameter Overall Height 143-1/2" Oneida Air Systems... -
Page 7: System Dimensions
System Dimensions Nominal dimensions shown using Height Position 3; Telescoping Stand can be adjusted to accommodate smaller waste containers. Dimensions subject to slight variations in manufacturing. Top View 82-3/4" 2,101 mm 39" 30-1/2" 991 mm 775 mm 143-1/2" 3,646 mm X"... -
Page 8: System Contents
You will need the following tools: GENER AL FAN HOUSING FILTER 8" Ladder Razor Knife Flathead Screwdriver 7/16" Wrench Level Diagonal Cutters Hammer 7/16" Socket Wrench Scissors Tape Measure / Ruler 1/2" Wrench 1/4" Socket 1/2" Socket Wrench Impact Driver Oneida Air Systems... - Page 9 System Contents (Continued) Note: Comes attached to × 4 the Motor Assembly (A) × 4 × 4 × 7 × 7 × 8 × 8 × 12 × 24 × 12 × 8 × 8 × 8 × 8 × 8 oneida-air.com...
-
Page 10: Assembly Instructions
Tip: Aim the dust collector's outlet away from the area where people tend to work to reduce noise. CORRECT CORRECT INCORRECT INLET INLET INLET Filter will obstruct inlet pipe Assemble the Stand (P) [FIG 1]. Refer to the instruction sheet included: • Stand Instruction Sheet # ZBI282321 FIG. 1 Oneida Air Systems... - Page 11 Assembly Instructions (Continued) Apply Gasket (O1) making sure that there is no gap where the ends meet: a. Apply to the top ange of the Cone (D) inside the bolt holes [FIG. 2a]. Top View Top View b. Apply to the top rim of the Barrel (C) outside of the bolt holes [FIG.
- Page 12 [FIG 5]. Secure the Fan Housing onto the Barrel using eight Flange Bolts (O2) and eight Flat Washers (O3). FIG. 5 10 Oneida Air Systems...
- Page 13 Assembly Instructions (Continued) THE MOTOR ASSEMBLY IS VERY HEAVY AND CUMBERSOME; BE SURE TO HAVE ADEQUATE HELP WHEN LIFTING! Carefully li Motor Assembly (A) to top of Fan Housing (B) and align the Fan Housing holes with the motor plate holes following the orientation shown in [FIG.
- Page 14 Plenum Extension to the Elbow (H) then the FIG. 8a 8x7x7 Pants Wye (I) and close the Clamps over the rolled ends. Lock the Clamps in place using the provided cotter pins [FIG. 8c]. FIG. 8b FIG. 8c 12 Oneida Air Systems...
- Page 15 Assembly Instructions (Continued) Attach the Dual Filter Plate (L) to the stand using the stand's pre-installed hardware as shown in [FIG. 9]. Note: Hardware should be nger tightened rst for ease of assembly when securing Filter Plate Assembly. Bolts Washers Whiz-Lock Nuts FIG.
- Page 16 Filter (N) [FIG. 11]. FIG. 11 Attach each Filter (N) to the Dual Filter Plate (L) with four J-Bolts (M4), four Flat Washers (M3) and four umb Nuts (M2) as shown in [FIG. 12]. FIG. 12 14 Oneida Air Systems...
- Page 17 Assembly Instructions (Continued) Attach a Fine Dust Bin (M6) to each Filter (N) with four J-Bolts (M4) and four umb Nuts (M2) as shown in [FIG. 13]. FIG. 13 To ground the lter, attach the ring terminal on the braided ground wire from the Motor Assembly (A) to a J-bolt (M4) on the Dual Filter Plate (L) under the umb Nut (M2),...
- Page 18 ENSURE THAT ALL ELECTRICAL POWER TO THE SYSTEM IS DISCONNECTED BEFORE PROCEEDING WITH FURTHER STEPS. Use the adhesive of your choice to temporarily secure the starter to the wall [FIG. 16]. To permanently secure the starter to the wall proceed to Step 17. FIG. 16 16 Oneida Air Systems...
- Page 19 Assembly Instructions (Continued) To permanently secure the starter to the wall, Mounting Screws Holes take off the starter cover by removing the top and bottom screws and exposing the overload and contact connections [FIG 17a]. Set aside the screws. START a.
-
Page 20: Maintenance
Corrosion Severe Dirt; > 122° F (50° C) Extreme Abrasive Dust; or Class H Insulation* Corrosion < -22° F (-30° C)** Temperature * Special HIGH temperature grease is recommended ** Special LOW temperature grease is recommended 18 Oneida Air Systems... -
Page 21: Troubleshooting
1. Remove the cowling and press the reset button. 2. If there is no room to remove the cowling, unplug your system for 1 minute. If you continue to experience difficulty with your dust collector, call Oneida Air Systems’ Customer Service Department at 1-866-387-8822 or email support@oneida-air.com. -
Page 22: F.a.q
F.A.Q. What dust can be collected? Oneida Air Systems’ dust collectors are designed and tested for wood and wood dust. ey can and have been used e ectively for various other dusts and chips, such as drywall dust, paper dust, agricultural dust, metal chips and other forms of debris. - Page 23 F.A.Q. (Continued) Should the inlet reducer for my dust collector be crimped or straight? e inlets on all of our dust collectors are sized to t standard ductwork. If you need a reducer to connect to ductwork that’s smaller than your collector’s inlet, the end of the reducer that connects to the inlet will need to be crimped, so that it will t inside the inlet.
-
Page 24: Recommended Accessories
• Single-piece, machine formed elbow constructed from heavy 22-gauge galvanized steel. • Large radius design for optimum airflow performance. • Uncrimped on both ends. 10" Collared Flange #DLX100000 • Made from heavy-duty, spot-welded, galvanized steel. • Easy to install onto your existing tool. • Pre-crimped for easy flex hose connections. 22 Oneida Air Systems... - Page 25 Universal Drum Dolly #SDD990000 • Fits nearly any cylindrical waste bin sold by Oneida Air Systems. • Includes ve 2" non-marking caster wheels (3 non-locking, 2 locking). • Requires Leg Extension Kit (Item #STZ212301) if used with a stand mounted system.
-
Page 26: Warranty Information
Oneida Air Systems makes every e ort to accurately represent our products and prices, however Oneida Air Systems reserves the right to make changes to products and prices at any time. As a manufacturer, Oneida Air Systems reserves the right to change product speci cations at any time in an e ort to achieve better quality products. -
Page 27: Notes
Notes oneida-air.com... - Page 28 Regardless of where you purchased your system, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems rst to let us help resolve your problem. We fully stand behind the quality of our products and place the utmost value on customer satisfaction.