Oneida Air Systems V-1500 Owner's Manual
  1. Manuals
  2. Brands
  3. Oneida Air Systems Manuals
  4. Dust Collector
  5. V1500
  6. Owner's manual

Oneida Air Systems V-1500 Owner's Manual

Hide thumbs Also See for V-1500:
Table of Contents

Advertisement

Quick Links

Download this manual
ZBM000101
V-SYSTEMS
8_10
Powerful Economical Made in the USA
Appearance may vary slightly.
1.800.732.4065
www.oneida-air.com
1001 W. Fayette St., Syracuse, NY 13204
Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art
dust collection systems and material handling ductwork to woodworking shops. OAS
designs and manufactures industrial grade dust collection systems that create a prac-
tical, safe and healthy work place environment.

Advertisement

Table of Contents
loading

Related Manuals for Oneida Air Systems V-1500

Summary of Contents for Oneida Air Systems V-1500

  • Page 1 1001 W. Fayette St., Syracuse, NY 13204 Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art dust collection systems and material handling ductwork to woodworking shops. OAS designs and manufactures industrial grade dust collection systems that create a prac-...

  • Page 2: Table Of Contents

    Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualifi ed technicians and sales staff are available 7:30am - 6:00pm EST Mon. - Thurs. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection.

  • Page 3: System Start-Up Information

    I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual Warning Do not operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place.

  • Page 4: System Specifi Cations

    *Oneida reserves the right to change or modify specs and system appearance without notice. Actual system appearance may vary. Oneida V- 1500 / V - 2000 2hp / V - 3000 3hp Part # Description 36” XXV010139H V-1500 Collector XXV020139H V-2000 Collector XXV030139H V-3000 Collector XXV050139H V-5000 Collector...

  • Page 5: Stand Assembly

    III. Stand Assembly Cone Stand Kit Contents Mounting Ring Gusset Hardware Kit (1) - AHX002107 Mid- Gusset Rubber Leg Cap (3) - RCR012500 Stand Leg Stand Brace Top Gusset (3) - RFG010000 Rubber Leg Cap Mid-Gusset (3) - RFG010003 Stand Braces 1.

  • Page 6: Cyclone Assembly

    IV. Cyclone Assembly Instructions for Attaching Motor Plate to Fan Housing. 1. Push clips onto inside circle on Fan Housing, making sure clip is pushed all of the way on, that the bolt holes are in alignment with the clip holes and that the small barrel on the clip is on the INSIDE of the Fan Housing as shown in diagram.
  • Page 7 4. Put included self-sticking gasket on top rim of cone. Make sure there is NO gap where both ends of gasket 5. Put cone on stand and meet. This is VERY important for an attach with provided hardware air tight seal. as shown on page 4.

  • Page 8: Plenum Elbow Assembly

    V. V-Systems Plenum Elbow Assembly 10. Attach plenum with provided sheet metal screws and seal well with sili- cone to prevent dust blow out. This is accomplished easier with two people. Drill 4 to 6 holes in the plenum and outlet for the sheet metal screws while one person holds the plenum in position.

  • Page 9: Drum Assembly

    Filter Grounding Wire Take the alligator clip that is at the end of the green grounding wire attached to the motor and clip it to the fi lter mesh as shown below. Tape the ring terminal end to the wire. 13.

  • Page 10: Directions For Cleaning Filter

    VIII. Directions for Cleaning External Filter All steps should be done with a dust mask and eye protection. Proper fi lter clean- ing should not be neglected. A dirty fi lter can affect dust collector operation and fi lter life. 1.

  • Page 11: Electrical Data

    Motor 6’ long type SJT 14 AWG power cord What size circuit breaker for the V-1500? The circuit breaker OAS recommends is a 1 pole ‘HACR’ style (or equivalent) 20 amp rated for 120 volts AC. What size circuit breaker for the V-2000? The circuit breaker OAS recommends is a 2 pole ‘HACR’...

  • Page 12: Troubleshooting

    X. Troubleshooting Unplug unit before servicing or cleaning. V - Systems Owner’s Manual O.A.S. 2010...

  • Page 13: Fire Hazards

    XI. Fire Hazards - Read Before Installing and Operating Oneida Collectors are designed for WOOD DUST only!! Wood shaping and cutting processes generate wood chips, shavings, and dust. These materials are considered combustible. Air borne wood dust below 420 microns in size (.017 of an inch) in certain concentration ranges when ignited can deflagrate (burn quickly).

  • Page 14: Terms And Conditions

    Limited Warranty Oneida Air Systems warrants products it manufactures for a period of 1 year to the original purchaser from the date of purchase. Items not manufactured by O.A.S. are limited to their own manufacturer’s warranties. All electrical items such as magnetic starters, re- motes, sensors, pumps and sccessories are limited to 90 days.

  • Page 15: Fan Motor Maintenance

    XIII. Fan Motor Maintenance Per Baldor specifications, their 2 pole motors (3600 RPM) motors are to be relubricated every 5500 hours. Table 1 - Service Conditions Table 2 - Lubrication Interval Multiplier Per Baldor specifications, add .30 ounces (8.4 grams) of Mobil Polyrex grease by weight or .6 cubic inches (2 teaspoons) of Mobil Polyrex grease by volume.

  • Page 16: Wall Mount Assembly (Optional)

    XIV. Wall Bracket Assembly 1. The collector will seem quieter if the outlet is aimed away from the area people tend to work. Slots in the brackets are .406” x 1.00”. Note: Bolts included to mount bracket to collector. Hardware NOT included to mount to wall.

This manual is also suitable for:

V-2000V-3000

Table of Contents