Summary of Contents for Oneida Air Systems Dust Deputy AXD001004
Page 1
Oneida Air Systems, Inc. 2010 U.S. Patent #7,282,074 C1 U.S. Design Pat. Oneida Air Systems, Inc. 1001 W. Fayette St., Syracuse, NY 13204 App. # 29/358,526 Ph. 1.800.732.4065 or 315.476.5151 / Fax: 315.476.5044 29/358,497 29/342,738...
Page 2
XIV. Other Products By Oneida Air Systems Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualifi ed technicians and sales staff are available 8:30am - 5:00pm EST Mon. - Fri. to answer any questions concerning OAS products and dust collection.
Page 3
State of New York, County of Onondaga. Oneida Air Systems shall in no event be liable for death, injuries to persons or property or for inciden- tal, contingent, special, or consequential damages arising from the use of our product.
Page 4
II. D.I.Y. Kit Contents XII. Accessories Plastic D.I.Y. Dust Deputy® - AXD001004 U.S. Patent #7,282,074 C1 Drum Dolly Drum Dolly increases With the D.I.Y. Dust Deputy, you only receive the plastic cyclone. Deputy’s mobility. Part # Description Velcro straps hold drum You must supply all hardware and buckets yourself.
Page 5
XII. Accessories III. Ultimate Kit Contents Order Online at www.oneida-air.com Ultimate Dust Deputy® - AXD000009 - Adaptor, Cuff 2.5” - 2.25” (1) AXD250225 U.S. Patent #7,282,074 C1 Dust Sentry™ - Elbow 2.5” w/ valve (1) AXD600101 U.S. Design Pat. App. # 29/358,526 * Optional Elbow 2.5”...
Page 6
IV. Assembly Instructions for D.I.Y. Dust Deputy® XI. Troubleshooting The Dust Deputy is made of static dissipating plastic*. Dust Deputy® not separating well. (Only a tiny amount of dust should reach the vacuum.) Hose to These are the minimum parts you will need to acquire to use the Dust Deputy: Vacuum Air leak.
Page 7
X. Super Dust Deputy® Additional Ideas for the D.I.Y. Dust Deputy® Super Dust Deputy® - AXD002030 Gasket can be glued to bottom of Turn Any Single Stage Collector Into A Super Cyclonic Dust Collector! bucket lid. 1. Add A Super Dust Deputy® Cyclone. A.) An example of a plywood top that had Use Your...
Page 8
V. Assembly Instructions for Deluxe Dust Deputy® Kit IX. Adding Cyclones to Improve Performance Top View This is just one example of attaching the Deluxe Dust Example 1 Deputy® to a shop vacuum. Most shop vacuums will use similar steps but you may have to modify slightly for your particular vacuum.
Page 9
V. Assembly Instructions for Deluxe Dust Deputy® Kit VIII. Other Options for Securing Dust Deputy® Deluxe to Vacuum 4.) Position foam block on marks and drill two holes (upper Fig. 6 and lower) through foam block and bucket (Fig.6). Put the two supplied carriage bolts through the large washers and then through the bucket from the inside.
Page 10
V. Assembly Instructions for Deluxe Dust Deputy® Kit VIII. Possible Ways to Attach Dust Deputy® Deluxe to Shop Vacuums You may want to attach your Dust Deputy The Dust Deputy® is made of static dissipating plastic. to your shop vacuum for mobility, conve- nience or stability.
Page 11
VII. Installing the Dust Bagger V. Assembly Instructions for Deluxe Dust Deputy® Kit If hoses are not tight on the inlet, or keep Make sure larger Attach vacuum hose elbow diameter hoses are Fig.5 pulling off, use the included Hose Reten- with valve to vacuum as pushed up so they fi...
Page 12
VI. Assembly Instructions for Ultimate Dust Deputy® VI. Assembly Instructions for Ultimate Dust Deputy® 1. With a Phillips head screwdriver, attach 5. Pull up latch so hole in latch goes over the pin / the two rubber latches, one on either side of boss on Dust Box top.